Cleveland SD-1050-K 66 User manual

Cleveland
™
Project ________________________________
Item __________________________________
Quantity_______________________________
FCSI Section ____________________________
Approval _______________________________
Date __________________________________
1333 East 179 St.,
Cleveland, Ohio,U.S.A. 44110
Tel: [phone]
Fax: [phone]
Web Site:www.ClevelandRange.com
Email: [e-mail]
DIRECT STEAM KETTLES
Cleveland Standard Features
nType 304 Stainlesss Steel construction, with #4 finish on
Kettle
nFactory Assembled Kettle/Stand combinations with available
kettle capacities to suit most needs
nSteam Control Kit: includes: Needle Type Steam Control
Valve, Steam Trap, Condensate Strainer, Check Valve,
Nipples and Fittings, factory assembled and mounted on
kettles(s)
nKettles are Mounted on Stainless Steel Stand of Modular
Cabinetized Design
nHot and Cold Water Faucet with Swing Spout
nTable Top has Full Width Drain Trough equipped with
standing 1.50" diameter male Drain Connection
nSliding drain Catch Pan with Splash Shield, easy to
position for use
nKettles are 2/3 Steam Jacketed and include Lift-Off Covers
n50 psi Steam Jacket Rating
n50 psi Chrome Plated Saftey Valve
nManual Tilting, Balanced Design
nTypical approvals include NSF and ASME
Options & Accessories
pType 316 Stainless Steel Kettle Interior for high acid food
products (316)
pCooking Basket (BS)
pFood Strainer (FS)
pSteam Pressure Reducing Valve, where supply exceeds 45
psi (PRV)
pSteam Supply Moisture Separator/Trap (MS)
pSingle Pantry Faucet (SPK)
pWall Meter, wall mount (GM For MLMF)
pWater Cooling, wall mount
pBack Wall or Back Splash (BW-32 or BS-4)
pSelf Locking Hand Tilt Mechanism (HTK - 12 gallons only)
Shall be CLEVELAND, Kettle(s) with Stand, Model SD - _____ - K _____ , full
width Drain Trough with1 1/2" male Drain Connection, Sliding Catch Pan
and 2/3 Steam Jacketed Kettle(s) _____ ea. _____ Gallon (and _____ ea. _____
Gallon) Steam Jacket Ratings to be 50 psi; Kettle and Legs to be Type 304
Stainless Steel. To operate, connect directly to a steam source supplying
from 5 to 45 psi steam. Steam Condensate Trap and Strainer, Factory
Assembled and Installed; includes: Hot and Cold Water Faucet with Swing
Spout and Lift-Off Kettle Covers.
Short Form Specifications
MODELS:cSD-450-K6 cSD-1200-K612
cSD-650-K12 cSD-1600-K1212
cSD-1050-K20 cSD-1800-K2020
cSD-1050-K66
STAND MOUNTED, DIRECT STEAM
6, 12 or 20 GAL. TILTING, 2/3 STEAM JACKETED (1 or 2 EACH)
18" HIGH STAND with DRAIN
450, 650, 1050,1200 or 1600mm WIDTHS
SECT. XPAGE 7
0707

(NOTTOSCALE)
SECT
.XP AGE 8
0707
Litho in U.S.A.
NOTES:
Cleveland Range reserves right of design improvement or modification, as warranted.
Many regional, state and local codes exist and it is the responsibility of the owner and installer to comply with the codes.
Installation of backflow preventers, vacuum breakers and other specific coder requirements is the responsibility of the owner and installer.
Cleveland Range equipment is built to comply with applicable standards for manufacturers. Included among those approval agencies are U.L., A.G.A., NSF, ASME/N.Bd., CSA, CGA, ETL and others.
CAPACITIES: (in 4 oz. servings,
other sizes may be calculated.)
6Gallon / 23 liters . . . 160 per kettle
12 Gallon / 45 liters . . . 352 per kettle
20 Gallon / 80 liters . . . 704 per kettle