Cognex In-Sight 5100 User manual

In-Sight®5000 Series
Vision System
Reference Guide
2018 March 23
Revision: 5.6.0.15

Legal Notices
The software described in this document is furnished under license, and may be used or copied only in accordance with
the terms of such license and with the inclusion of the copyright notice shown on this page. Neither the software, this
document, nor any copies thereof may be provided to, or otherwise made available to, anyone other than the licensee.
Title to, and ownership of, this software remains with Cognex Corporation or its licensor. Cognex Corporation assumes
no responsibility for the use or reliability of its software on equipment that is not supplied by Cognex Corporation.
Cognex Corporation makes no warranties, either express or implied, regarding the described software, its
merchantability, non-infringement or its fitness for any particular purpose.
The information in this document is subject to change without notice and should not be construed as a commitment by
Cognex Corporation. Cognex Corporation is not responsible for any errors that may be present in either this document or
the associated software.
Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document
may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, nor
transferred to any other media or language without the written permission of Cognex Corporation.
Copyright © 2003 - 2016. Cognex Corporation. All Rights Reserved.
Portions of the hardware and software provided by Cognex may be covered by one or more U.S. and foreign patents, as
well as pending U.S. and foreign patents listed on the Cognex web site at: http://www.cognex.com/patents.
The following are registered trademarks of Cognex Corporation:
Cognex, 2DMAX, Advantage, AlignPlus, Assemblyplus, CheckitwithChecker, Checker, CognexVisionforIndustry,
CognexVSOC, CVL, DataMan, DisplayInspect, DVT, EasyBuilder, Hotbars, IDMax, In-Sight, LaserKiller, MVS-8000,
OmniView, PatFind, PatFlex, PatInspect, PatMax, PatQuick, SensorView, SmartView, SmartAdvisor, SmartLearn,
UltraLight, VisionSolutions, VisionPro, VisionView
The following are trademarks of Cognex Corporation:
The Cognex logo, 1DMax, 3D-Locate, 3DMax, BGAII, CheckPoint, CognexVSoC, CVC-1000, FFD, iLearn, In-Sight
(design insignia with cross-hairs), In-Sight2000, InspectEdge, Inspection Designer, MVS, NotchMax, OCRMax,
PatMaxRedLine, ProofRead, SmartSync, ProfilePlus, SmartDisplay, SmartSystem, SMD4, VisiFlex, Xpand
Portions copyright © Microsoft Corporation. All rights reserved.
Portions copyright © MadCap Software, Inc. All rights reserved.
Other product and company trademarks identified herein are the trademarks of their respective owners.
2
Legal Notices

Regulations/Conformity
Note: For the most up-to-date CE declaration and regulatory conformity information, please refer to the Cognex
online support site: http://www.cognex.com/Support.
Safety and Regulatory
Manufacturer Cognex Corporation
One Vision Drive
Natick, MA 01760 USA
In-Sight 5100/5110/5400/5410: Type 821-0034-1R
In-Sight 5100C/5400C: Type 821-0036-1R
In-Sight 5403/5413: Type 821-0037-1R
FCC FCC Part 15, Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference; and (2) this device must accept any
interference received, including interference that may cause undesired operation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
KCC In-Sight 5100/5110/5400/5410: CGX-IS5400-01(A)
In-Sight 5100C/5400C: CGX-IS5400-C01(A)
In-Sight 5403/5413: CGX-IS5403-01(A)
NRTL TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 60950-1.
CB TÜV SÜD AM, IEC/EN 60950-1. CB report available upon request.
RoHS Compliant to the latest applicable Directive.
3
Regulations/Conformity

Safety and Regulatory
Manufacturer Cognex Corporation
One Vision Drive
Natick, MA 01760 USA
In-Sight 5600/5610: Type 821-0041-1R
In-Sight 5603/5613: Type 821-0042-1R
In-Sight 5604/5614: Type 821-0051-1R
In-Sight 5605/5615: Type 821-0032-1R; Type 821-0032-2R
In-Sight 5705/5715/5705C: Regulatory Model 1AAF
FCC FCC Part 15, Class A
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) this device may not cause harmful interference; and (2) this device must accept any
interference received, including interference that may cause undesired operation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance
with the instruction manual, may cause harmful interference to radio communications. Operation of this
equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at their own expense.
KCC In-Sight 5600/5610: KCC-REM-CGX-IS5600-01
In-Sight 5603/5613: KCC-REM-CGX-IS5603-01
In-Sight 5604/5614: KCC-REM-CGX-IS5604-01
In-Sight 5605/5615: CGX-IS5605-01(A)
In-Sight 5705/5715/5705C: Regulatory Model 1AAF: MSIP-REM-CGX-1AAF
NRTL TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 61010-1.
CB TÜV SÜD AM, IEC/EN 61010-1. CB report available upon request.
RoHS Compliant to the latest applicable Directive.
4
Regulations/Conformity

For European Community Users
Cognex complies with Directive 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012
on waste electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its production. It may contain hazardous
substances that could impact health and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural
resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or
recycle most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal
waste and invites you to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste
administration.
You may also contact your supplier for more information on the environmental performance of this product.
5
Regulations/Conformity

Precautions
Observe these precautions when installing the Cognex product, to reduce the risk of injury or equipment damage:
lIn-Sight 5000 series vision systems are intended to be supplied by a UL or NRTL listed power supply with a
24VDC output rated for at least 600 mA continuous and a maximum short circuit current rating of less than 8A and
a maximum power rating of less than 100VA and marked Class 2 or Limited Power Source (LPS). Any other
voltage creates a risk of fire or shock and can damage the components. Applicable national and local wiring
standards and rules must be followed.
lDo not install Cognex products where they are directly exposed to environmental hazards such as excessive
heat, dust, moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static electricity.
lTo reduce the risk of damage or malfunction due to over-voltage, line noise, electrostatic discharge (ESD), power
surges, or other irregularities in the power supply, route all cables and wires away from high current wiring or
high-voltage power sources.
lThe housing of the vision system is internally connected to the system ground wire (pin 8 of the Breakout cable).
Therefore, if the mounting surface of the vision system is at a non-zero ground potential, it is strongly
recommended that the vision system be mounted on an isolated or non-conductive mount.
lDo not expose the image sensor to laser light; image sensors can be damaged by direct, or reflected, laser light.
If your application requires the use of laser light that may strike the image sensor, a lens filter at the
corresponding laser's wavelength is recommended. Contact your local integrator or application engineer for
suggestions.
lThe In-Sight vision system does not contain user-serviceable parts. Do not make electrical or mechanical
modifications to In-Sight vision system components. Unauthorized modifications may void your warranty.
lChanges or modifications not expressly approved by the party responsible for regulatory compliance could void
the user’s authority to operate the equipment.
lService loops should be included with all cable connections.
lCable shielding can be degraded or cables can be damaged or wear out more quickly if a service loop or bend
radius is tighter than 10X the cable diameter. The bend radius must begin at least six inches from the connector.
lThis device is certified for office use only and if used at home, there can be frequency interference problems.
lThis device should be used in accordance with the instructions in this manual.
6
Precautions

Table of Contents
Legal Notices 2
Regulations/Conformity 3
For European Community Users 5
Precautions 6
Table of Contents 7
Introduction 8
Support 8
Standard Components 8
Accessories 9
Cables 9
I/O Modules 11
Installation 13
Connectors and Indicators 13
Install the Lens 14
Connect the Ethernet Cable 14
Connect the Breakout Cable 15
Specifications 16
5100, 5100C, 5400C, 5403 and 5400 Vision System Specifications 16
5603, 5600 and 5605 Vision System Specifications 18
5604 Line Scan Vision System Specifications 20
5705 and 5705C Vision System Specifications 22
I/O Specifications 24
Acquisition Trigger Input 24
Encoder Inputs (In-Sight 5604 Only) 25
High-Speed Outputs 26
5100 and 5400 Series Vision System Ethernet Cable Specifications 28
5600 and 5700 Series Vision System Ethernet Cable Specifications 29
Breakout Cable Specifications 30
I/O Module Cable Specifications 31
Dimensional Drawings 32
5100, 5100C, 5400, 5400C and 5403 Vision System (With Lens Cover) 32
5100, 5100C, 5400, 5400C and 5403 Vision System (Without Lens Cover) 33
5600 and 5603 Vision System (With Lens Cover) 34
5600 and 5603 Vision System (Without Lens Cover) 35
5604, 5605, 5705, and 5705C Vision System (With Lens Cover) 36
5604, 5605, 5705, and 5705C Vision System (Without Lens Cover) 37
Cleaning/Maintenance 38
Clean the Vision System Housing 38
Clean the Vision System Image Sensor Window 38
Clean the Vision System Lens Cover 38
7
Table of Contents

Introduction
The In-Sight®vision system is a compact, network-ready, stand-alone machine vision system used for automated
inspection, measurement, identification and robot guidance applications on the factory floor. All models can be easily
configured remotely over a network using an intuitive user interface.
Support
Many information resources are available to assist you in using the vision system:
lThe In-Sight®Explorer Help and EasyBuilder Help files, provided with In-Sight Explorer software.
lOn-demand training: http://www.cognex.com/on-demand-training.aspx.
lThe In-Sight online support site: http://www.cognex.com/Support/InSight.
Standard Components
The vision system is shipped with the standard components listed below.
Note: Cables are sold separately.
Component In-Sight 5100/5110
In-Sight 5100C
In-Sight 5400C
In-Sight 5400/5410
In-Sight 5403/5413
In-Sight 5600/5610
In-Sight 5603/ 5613
In-Sight 5604/5614
In-Sight 5605/5615
In-Sight 5705/5715
In-Sight 5705C
50mm Lens Cover Kit
(P/N 800-5842-xR)
X X
80mm Lens Cover Kit
(P/N 823-0133-xR)
X
Thread Guard
(P/N 370-0361)
X X X
Mounting Screw Kit
(P/N 800-5843-xR)
X X X
Component Description
Vision System Provides image acquisition, vision processing, job storage, serial and Ethernet
connectivity and discrete I/O.
Lens Cover Kit (includes
lens cover and O-Ring)
Provides environmental protection for the lens.
Thread Guard Protects the In-Sightvision system lens cover threads when the lens cover is not used.
Remove the thread guard prior to installing the lens cover.
Mounting Screw Kit Includes M4 screws for mounting the vision system (quantity 4).
8
Introduction

Accessories
The following components can be purchased separately. For a complete list of options and accessories, contact your
local Cognex sales representative.
Cables
Note: Cables are sold separately.
CAUTION:All cable connectors are “keyed” to fit the connectors on the vision system; do not force the connections
or damage may occur.
Ethernet Cable
The Ethernet cable is used to connect the vision system to other network devices. The pin-outs for the cable are listed in
the 5100 and 5400 Series Vision System Ethernet Cable Specifications on page28 and 5600 and 5700 Series Vision
System Ethernet Cable Specifications on page29. This cable is available in the lengths and styles listed below.
Length Standard Part # 45-Degree Key Right-Angle Part # 135-Degree Key Right Angle Part #
0.6 m CCB-84901-1001-00 N/A N/A
2 m CCB-84901-1002-02 CCB-84901-6005-02 CCB-84901-7005-02
5 m CCB-84901-1003-05 CCB-84901-6001-05 CCB-84901-7001-05
10 m CCB-84901-1004-10 CCB-84901-6002-10 CCB-84901-7002-10
15 m CCB-84901-1005-15 CCB-84901-6003-15 CCB-84901-7003-15
30 m CCB-84901-1006-30 CCB-84901-6004-30 CCB-84901-7004-30
9
Introduction

Breakout Cable
The Breakout cable provides connection to an external power supply, RS-232 serial communications, acquisition trigger
input, high-speed outputs and encoder inputs (In-Sight 5604 only). The pin-outs for the cable are listed in the Breakout
Cable Specifications on page30. This cable is available in the lengths listed below.
Length Standard Part # 45-Degree Key Right-Angle Part # 135-Degree Key Right Angle Part #
2 m CCB-84901-0101-02 CCB-84901-0401-02 CCB-84901-0501-02
5 m CCB-84901-0102-05 CCB-84901-0402-05 CCB-84901-0502-05
10 m CCB-84901-0103-10 CCB-84901-0403-10 CCB-84901-0503-10
15 m CCB-84901-0104-15 CCB-84901-0404-15 CCB-84901-0504-15
10
Introduction

I/O Module Cable
The I/O Module cable connects the vision system directly to a compatible In-Sight I/O module via the DB15 connector.
The pin-outs for the cable are listed in the I/O Module Cable Specifications on page31. This cable is available in the
lengths listed below.
Length Standard Part # 45-Degree Key Right-Angle Part # 35-Degree Key Right-Angle Part #
2 m CCB-84901-0901-02 CCB-84901-4001-02 CCB-84901-5001-02
5 m CCB-84901-0902-05 CCB-84901-4002-05 CCB-84901-5002-05
10 m CCB-84901-0903-10 CCB-84901-4003-10 CCB-84901-5003-10
15 m CCB-84901-0904-15 CCB-84901-4004-15 CCB-84901-5004-15
I/O Modules
The following I/O modules are compatible with your vision system, and provide access to additional discrete inputs and
outputs.
I/O Module Vision System Discrete
Inputs
Discrete
Outputs
CIO-1400 All In-Sight 5000 series vision systems (except In-Sight 5604) 7 general 2high-speed,
6 general
CIO-MICRO All In-Sight 5000 series vision systems 8 general 2high-speed,
8 general
CIO-MICRO-CC All In-Sight 5000 series vision systems (except In-Sight 5705, 5705C
and 5715)
8 general 2high-speed,
8 general
11
Introduction

Note:
lThe CIO-MICRO I/O module only supports In-Sight 5700 series vision systems with firmware version 5.3.0
and higher.
lThe CIO-MICRO and CIO-MICRO-CC I/O modules do not support 1000 BaseT pass-through operation. If
1000 BaseT operation is required when using the In-Sight 5600 series or In-Sight 5700 series vision
system, you must connect a LAN cable from a Gigabit Ethernet switch to the I/O module’s LAN port and
connect the vision system’s Ethernet cable to the Gigabit Ethernet switch.
lThe CIO-MICRO & CIO-MICRO-CC I/O modules support In-Sight 5100 series and 5400 series vision
systems with 128MB non-volatile flash memory or higher and support all In-Sight 5600 series vision
systems.
lThe CIO-MICRO-CC I/O module also adds CC-link networking capability. Refer to the In-Sight®CIO-MICRO
and CIO-MICRO-CC I/O Module Installation Manual for detailed connection information.
12
Introduction

Installation
This section describes the connection of the vision system to its standard components and accessories.For a complete
list of options and accessories, contact your Cognex sales representative.
Note:
lCables are sold separately.
lIf any of the standard components appear to be missing or damaged, immediately contact your Cognex
Authorized Service Provider (ASP) or Cognex Technical Support.
CAUTION:All cable connectors are “keyed” to fit the connectors on the vision system; do not force the connections
or damage may occur.
Connectors and Indicators
Connector/Indicator Function
24VDC Connector Connects the Breakout cable, which provides connections to an external power
supply, the acquisition trigger input, high-speed outputs and RS-232 serial
communications. For more information, refer to Breakout Cable Specifications on
page30. Alternately, this connector is used to attach the I/O Module cable to an
optional In-Sight I/O module, which adds general-purpose discrete I/O and light
control functionality. For more information, refer to the I/O Module Cable
Specifications on page31.
User 1 LED Green when active. User-configurable within the In-Sight Explorer Discrete Output
Settings dialog, using Discrete Output Line 4 (Line 10 for all I/O modules, except
the CIO-1400, which uses Line 9).
User 0 LED Red when active. User-configurable within the In-Sight Explorer Discrete Output
Settings dialog, using Discrete Output Line 5 (Line 11 for all I/O modules, except
the CIO-1400, which uses Line 10).
Power LED Green when power is applied.
Network Traffic LED Flashes green while transmitting and receiving data.
Network Status LED Green when a network connection is detected.
ENET Connector Connects the vision system to a network. The ENET connector provides the
Ethernet connection to external network devices. For more information, refer to the
5100 and 5400 Series Vision System Ethernet Cable Specifications on page28
and 5600 and 5700 Series Vision System Ethernet Cable Specifications on
page29.
13
Installation

Note:
lFor the In-Sight 5100 and 5400 series, when the vision system is powered up, User 0 LED and User 1 LED
both momentarily turn on. Then, User 0 LED turns off and User 1 LED stays on. Next, User 0 LED turns on
and User 1 LED turns off. Finally, both LEDs momentarily turn on and then turn off.
lFor the In-Sight 5600 series and In-Sight 5700 series, when the vision system is powered up, User 0 LED
and User 1 LED both momentarily turn on. Then, User 1 LED turns off and User 0 LED stays on. Next, User
1 LED turns on and User 0 LED turns off. Finally, both LEDs momentarily turn on and then turn off.
Install the Lens
1. Remove the protective film covering the threaded lens opening, if present.
2. Attach a C-Mount lens to the vision system. The exact lens focal length needed depends on the working distance
and the field of view required for your machine vision application.
3. If using a lens cover, remove the thread guard and attach the lens to the vision system.
Connect the Ethernet Cable
1. Connect the Ethernet cable’s M12 connector to the vision system’s ENET connector.
2. Connect the Ethernet cable’s RJ-45 connector to a switch/router or PC, as applicable.
14
Installation

Connect the Breakout Cable
Note: Unused wires can be clipped short or tied back using a tie made of non-conductive material. Keep all bare
wires separated from the +24VDC wire.
1. Verify that the 24VDC power supply being used is unplugged and not receiving power.
2. Optionally, connect the I/O or serial wires to an appropriate device (for example, a PLC, an encoder, or a serial
device). For more information, refer to Breakout Cable Specifications on page30.
Note: When using an In-Sight 5604 line scan vision system, the RS-232RX wire is used as Encoder A and
the RS-232TX wire is used as Encoder B. For more information, refer to Encoder Inputs (In-Sight 5604 Only)
on page25.
3. Attach the I/O Breakout cable's +24VDC (White/Green wire) and 24V COMMON (Brown wire) to the
corresponding terminals on the power supply. Refer to Breakout Cable Specifications on page30 for wiring
details.
CAUTION:Never connect voltages other than 24VDC. Always observe the polarity shown.
4. Attach the Breakout cable's M12 connector to the vision system's 24VDC connector.
5. Restore power to the 24VDC power supply and turn it on if necessary.
15
Installation

Specifications
The following sections list general specifications for the In-Sight 5000 series vision systems.
5100, 5100C, 5400C, 5403 and 5400 Vision System
Specifications
Specification 5100/5110 5100C 5400C 5403/5413 5400/5410
Minimum
Firmware
Requirement1
In-Sight version 4.4.3
Job/Program
Memory
128MB non-volatile flash memory; unlimited storage via remote network device.
Image
Processing
Memory
256MB SDRAM
Sensor Type 1/3-inch CCD 1/1.8-inch CCD 1/3-inch CCD
Sensor
Properties
5.92mm diagonal,
7.4 x 7.4µm sq. pixels
5.92mm diagonal,
7.4 x 7.4µm sq.
pixels
8.8mm diagonal,
4.4 x 4.4µm sq.
pixels
5.92mm diagonal,
7.4 x 7.4µm sq.
pixels
Maximum
Resolution
(pixels)2
640 x 480 640 x 480 1600 x 1200 640 x 480
Electronic
Shutter Speed
16µs to 1000ms 16µs to 1000ms 27µs to 1000ms 16µs to 1000ms
Acquisition Rapid reset, progressive scan, full-frame integration.
Bit Depth 256 grey levels (8
bits/pixel)
24-bit color 24-bit color 256 grey levels (8 bits/pixel)
Frames Per
Second360 full frames per second. 60 full frames per second.
14 full frames per
second.
60 full frames per
second.
Lens Type C-mount
Lens Cover
View Port
Material
Clear plastic with an abrasion-resistant coating on the exterior side.
Trigger 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet and RS-232C.
Discrete Inputs None built-in. Additional inputs available using a compatible I/O module. (For more information, refer
to I/O Modules on page11.) Unlimited inputs when using an Ethernet I/O system.
Discrete Outputs 2 built-in, high-speed outputs. Additional outputs available using a compatible I/O module. (For more
information, refer to I/O Modules on page11.) Unlimited outputs when using an Ethernet I/O system.
Status LEDs Power, Network Status, Network Traffic, 2 user configurable.
Network
Communication
1 Ethernet port, 10/100 BaseT, TCP/IP protocol. Supports DHCP (factory default), static and link-local
IP address configuration.
1The In-Sight firmware version 5.1.0 and higher is not supported on In-Sight 5100/5110, 5100C, 5400C, 5403/5413 and 5400/5410 vision
systems.
2The number of image sensor rows are configurable and can be set within the In-Sight Explorer software. Decreasing the number of rows will
increase the number of frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight®Explorer Help file for
more information.
3For In-Sight 5100/5110, 5100C, 5400C, 5403/5413 and 5400/5410 vision systems, the maximum frames per second is job-dependent, based
on the minimum exposure for a full image frame capture using the dedicated acquisition trigger, and assumes there is no user interface
connection to the vision system.
16
Specifications

Specification 5100/5110 5100C 5400C 5403/5413 5400/5410
1588 Support1Timestamp Resolution: 8ns
Synchronization Accuracy Through Transparent Clock: 5µs
Serial
Communication
RS-232C when connected to the Breakout Cable or a compatible I/O module. (For more information,
refer to I/O Modules on page11.)
Power
Consumption
24VDC ±10%, 500mA maximum.
Material Die-cast aluminum housing.
Finish Painted.
Mounting Eight M4 threaded mounting holes (four front and four back).
Dimensions 83.4mm (3.28in) x 124.2mm (4.89in) x 61.4mm (2.42in) with lens cover installed.
43.5mm (1.71in) x 124.2mm (4.89in) x 61.4mm (2.42in) without lens cover installed (includes Thread
Guard).
Weight 350 g (12.3 oz.) Lens cover installed, without lens.
Operating
Temperature
0°C to 45°C (32°F to 113°F)
Storage
Temperature
-30°C to 80°C (-22°F to 176°F)
Humidity 95%, non-condensing (Operating and Storage)
Protection IP67 (with appropriate lens cover properly installed).
Shock (Shipping
and Storage)
80 G Shock with 150 gram lens attached per IEC 68-2-27.
Vibration
(Shipping and
Storage)
10 G from 10-500 Hz with 150 gram lens per IEC 68-2-6.
Regulatory
Compliance
CE, FCC, KCC, TÜV SÜD NRTL, RoHS
11588 is only supported on vision systems running firmware version 4.5.0 and higher.
17
Specifications

5603, 5600 and 5605 Vision System Specifications
Specification 5603/5613 5600/5610 5605/5615
Minimum
Firmware
Requirement1
In-Sight version 4.4.3 In-Sight version 4.4.1
Job/Program
Memory
128MB non-volatile flash memory; unlimited storage via remote network device.
Image
Processing
Memory
256MB SDRAM
Sensor Type 1/1.8-inch CCD 1/3-inch CCD 2/3-inch CCD
Sensor
Properties
8.8mm diagonal, 4.4 x
4.4µm sq. pixels
5.92mm diagonal, 7.4 x
7.4µm sq. pixels
11.01mm diagonal, 3.45 x 3.45µm sq. pixels
Maximum
Resolution
(pixels)2
1600 x 1200 640 x 480 2448 x 2048
Electronic
Shutter Speed
27µs to 1000ms 32µs to 1000ms 28.8µs to 1000ms
Acquisition Rapid reset, progressive scan, full-frame integration.
Bit Depth 256 grey levels (8 bits/pixel)
Frames Per
Second314 full frames per second. 60 full frames per second. 16 full frames per second.
Lens Type C-mount
Lens Cover View
Port Material
Clear plastic with an abrasion-resistant coating on the exterior side.
Trigger 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet and RS-232C.
Discrete Inputs None built-in. Additional inputs available using a compatible I/O module. (For more information, refer
to I/O Modules on page11.) Unlimited inputs when using an Ethernet I/O system.
Discrete Outputs 2 built-in, high-speed outputs. Additional outputs available using a compatible I/O module. (For more
information, refer to I/O Modules on page11.) Unlimited outputs when using an Ethernet I/O system.
Status LEDs Power, Network Status, Network Traffic, 2 user configurable.
Network
Communication
1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3 TCP/IP protocol. Supports DHCP
(factory default), static and link-local IP address configuration.
1588 Support4Timestamp Resolution: 8ns
Synchronization Accuracy Through Transparent Clock: 5µs
Serial
Communication
RS-232C when connected to the Breakout Cable or a compatible I/O module. (For more information,
refer to I/O Modules on page11.)
Power
Consumption
24VDC ±10%, 600mA maximum.
Material Die-cast aluminum housing.
Finish Painted/Powder coat (back plate).
1The In-Sight firmware version 5.1.0 and higher is not supported on In-Sight 5603/5613, 5600/5610 and 5605/5615 vision systems.
2The number of image sensor rows are configurable and can be set within the In-Sight Explorer software. Decreasing the number of rows will
increase the number of frames per second acquired by the vision system. Refer to the AcquireImage topic in the In-Sight®Explorer Help file for
more information.
3Maximum frames per second is job-dependent, based on the minimum exposure for a full image frame capture using the dedicated acquisition
trigger, and assumes there is no user interface connection to the vision system.
41588 is only supported on vision systems running firmware version 4.5.0 and higher.
18
Specifications

Specification 5603/5613 5600/5610 5605/5615
Mounting Eight M4 threaded mounting holes (four front and four back).
Dimensions 99.9mm (3.93in) x 124.2mm (4.89in) x 61.4mm
(2.42in) with lens cover installed.
60.1mm (2.37in) x 124.2m (4.89in) x 61.4mm (2.42in)
without lens cover installed.
134.4mm (5.29in) x 124.1mm (4.88in) x
61.4mm (2.42in) with lens cover installed.
53.2mm (2.09in) x 124.1mm (4.88in) x
61.4mm (2.42in) without lens cover installed
(includes Thread Guard).
Weight 463 g (16.3 oz.) Lens
cover installed, without
lens.
409 g (14.4 oz.) Lens
cover installed, without
lens.
538 g (19.0 oz.) Lens cover installed,
without lens.
Operating
Temperature
(non-circulating
air)
0°C to 45°C (32°F to 113°F)1
Operating
Temperature
(circulating air)
0°C to 50°C (32°F to
122°F)20°C to 50°C (32°F to
122°F)30°C to 50°C (32°F to 122°F)4
Storage
Temperature
-30°C to 80°C (-22°F to 176°F)
Humidity 95%, non-condensing (Operating and Storage)
Protection IP67 (with appropriate lens cover properly installed).
Shock (Shipping
and Storage)
80 G Shock with 150 gram lens attached per IEC 68-2-27.
Vibration
(Shipping and
Storage)
10 G from 10-500 Hz with 150 gram lens per IEC 68-2-6.
Regulatory
Compliance
CE, FCC, KCC, TÜV SÜD NRTL, RoHS
1The vision system should be mounted with sufficient clearance on all sides to allow air circulation around and through the cooling posts on the
black heat sink.
2Additional cooling from a fan is recommended for operation above 40°C. For operation up to 50°C, there must be ≥16 CFM of air moving
through the cooling posts on the black heat sink.
3Additional cooling from a fan is recommended for operation above 40°C. For operation up to 50°C, there must be ≥4 CFM of air moving
through the cooling posts on the black heat sink.
4Additional cooling from a fan is recommended for operation above 40°C. For operation up to 50°C, there must be ≥16 CFM of air moving
through the cooling posts on the black heat sink.
19
Specifications

5604 Line Scan Vision System Specifications
Specification 5604/5614
Minimum Firmware
Requirement1In-Sight version 4.4.3
Job/Program
Memory
128MB non-volatile flash memory; unlimited storage via remote network device.
Image Processing
Memory
256MB SDRAM
Sensor Type 1-inch CCD
Sensor Properties 14.3 mm x 14µm active area, 14µm x 14µm sq. pixels.
Maximum
Resolution (pixels)
1024 x 1 (CCD); 1024 x 8192 (up to 8192 lines for full resolution image).
Acquisition Line Scan integration.
Bit Depth 256 grey levels (8 bits/pixel)
Lines Per Second 44K lines per second.
Lens Type C-mount
Lens Cover View
Port Material
Clear plastic with an abrasion-resistant coating on the exterior side.
Trigger 1 opto-isolated, acquisition trigger input. Remote software commands via Ethernet and RS-232C.
Discrete Inputs None built-in. Additional inputs available using a compatible I/O module. (For more information,
refer to I/O Modules on page11.) Unlimited inputs when using an Ethernet I/O system.
Discrete Outputs 2 built-in, high-speed outputs. Additional outputs available using a compatible I/O module. (For
more information, refer to I/O Modules on page11.) Unlimited outputs when using an Ethernet I/O
system.
Encoder Inputs 2 built-in, encoder inputs for use with a 24VDC signal.
Status LEDs Power, Network Status, Network Traffic, 2 user configurable.
Network
Communication
1 Ethernet port, 10/100/1000 BaseT with auto MDIX. IEEE 802.3 TCP/IP protocol. Supports
DHCP (factory default), static and link-local IP address configuration.
1588 Support Timestamp Resolution: 8ns
Synchronization Accuracy Through Transparent Clock: 5µs
Serial
Communication
RS-232C when connected to compatible I/O module. (For more information, refer to I/O Modules
on page11.)
Power Consumption 24VDC ±10%, 600mA maximum.
Material Die-cast aluminum housing.
Finish Painted/Powder coat (back plate).
Mounting Eight M4 threaded mounting holes (four front and four back).
Dimensions 134.4mm (5.29in) x 124.1mm (4.88in) x 61.4mm (2.42in) with lens cover installed.
53.2mm (2.09in) x 124.1mm (4.88in) x 61.4mm (2.42in) without lens cover installed (includes
Thread Guard).
Weight 585 g (20.6 oz.) Lens cover installed, without lens.
Operating
Temperature (non-
circulating air)
0°C to 45°C (32°F to 113°F)2
1The In-Sight firmware version 5.1.0 and higher is not supported on In-Sight 5604/5614 vision systems.
2The vision system should be mounted with sufficient clearance on all sides to allow air circulation around and through the cooling posts on the
black heat sink. If the vision system is not mounted with sufficient clearance, a fan is recommended.
20
Specifications