Cognex In-Sight 2800 Series User manual

In-Sight®2800 Series
Quick Reference Guide
2023 March 31
Revision: 23.1.0.120

Precautions
To reduce the risk of injury or equipment damage, observe the following
precautions when you install the Cognex product:
lConnectivity is possible through the following options:
l24 VDC (+/- 10%) output connection using a UL or NTRL listed
power supply
Any other voltage creates a risk of fire or shock and can damage the
components. Applicable national and local wiring standards and rules must
be followed.
lThis product is intended for industrial use in automated manufacturing or
similar applications.
lThe safety of any system incorporating this product is the responsibility of
the assembler of the system.
lDo not install Cognex products where they are exposed to environmental
hazards such as excessive heat, dust, moisture, humidity, impact,
vibration, corrosive substances, flammable substances, or static electricity.
lDo not expose the image sensor to laser light. Image sensors can be
damaged by direct, or reflected, laser light. If your application requires
laser light that might strike the image sensor, use a lens filter at the
corresponding laser wavelength. For suggestions, contact your local
integrator or application engineer.
lRoute cables and wires away from high-current wiring or high-voltage
power sources to reduce the risk of damage or malfunction from the
following causes: over-voltage, line noise, electrostatic discharge (ESD),
power surges, or other irregularities in the power supply.
2

lDo not expose the image sensor to laser light. Image sensors can be
damaged by direct, or reflected, laser light. If your application requires
laser light that might strike the image sensor, use a lens filter at the
corresponding laser wavelength. For suggestions, contact your local
integrator or application engineer.
lThis product does not contain user-serviceable parts. Do not make
electrical or mechanical modifications to product components.
Unauthorized modifications can void your warranty.
lChanges or modifications not expressly approved by the party responsible
for regulatory compliance could void the user’s authority to operate the
equipment.
lInclude service loops with cable connections.
lEnsure that the cable bend radius begins at least six inches from the
connector. Cable shielding can be degraded or cables can be damaged or
wear out faster if a service loop or bend radius is tighter than 10X the cable
diameter.
lThis device should be used in accordance with the instructions in this
manual.
lAll specifications are for reference purposes only and can change without
notice.
3

Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or
electrical shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
4

Accessories
You can purchase the following components separately. For a list of options and
accessories, contact your local Cognex sales representative.
Lenses
Accessory Product Number Illustration
12mm Manual Focus Lens Module to be used with Multi Torch light 280-TORCH-
MAN12
16mm Manual Focus Lens Module to be used with Multi Torch light 280-TORCH-
MAN16
Blue bandpass filter supported with IS2800 Mini with 6.2mm lens
illumination only
DM150-BP470
Blue bandpass filter, 450 nm 280-TORCH-
BP450
Red bandpass filter DM150-BP635
Red bandpass filter, 635 nm 280-TORCH-
BP635
5

Accessory Product Number Illustration
16 mm High Speed Liquid Lens - Visible and Near-IR Light CLN-C16F8FS-
HSLL
24 mm High Speed Liquid Lens - Visible and Near-IR Light CLN-C24F6FS-
HSLL
16 mm Manual Focus lens for Multi Torch - Visible and Near IR Light CLN-C16F8FS
24 mm Manual Focus lens for Multi Torch - Visible and Near-IR Light CLN-C24F6FS
Blue bandpass filter for Multi Torch 380-TORCH-
BP470
Red bandpass filter for Multi Torch 380-TORCH-
BP635
6

Lens Covers
Accessory Product Number Illustration
Standard front cover. Use with a 6.2 mm lens only. DM280-CVR-62
Standard front cover, fully-polarized. Use with a 6.2 mm lens only. DM260-LENS-62CVR-F
Extended front cover. Use with a 16 mm lens only. DM260-LENS-16CVR
Extended front cover, half-polarized. Use with a 16 mm lens only. DM260-LENS-16CVR-P
Extended front cover, fully-polarized. Use with a 16 mm lens only. DM260-LENS-16CVR-F
Cross-polarized cover for Multi Torch 280-TORCH-COVPOL
Clear cover for Multi Torch 280-TORCH-COVCLR
Diffuse cover for Multi Torch 280-TORCH-COVDIF
45mm Plastic Lens Cover COV-380-CMNT-45
60mm Plastic Lens Cover COV-380-CMNT-60
7

Accessory Product Number Illustration
75mm Plastic Lens Cover COV-380-CMNT-75
30mm Lens Cover Extender COV-7000-CMNT-LGX
Multi Torch front cover - Diffused 380-TORCH-COVDIF
Multi Torch front cover - Cross-Polarized 380-TORCH-COVPOL
Multi Torch front cover - Clear 380-TORCH-COVCLR
Dome Attachment for 380 platform Multi Torch and DataMan HPIT 380-TORCH-DOME
CAUTION:For 280-TORCH-COVPOL, 280-TORCH-COVCLR, and 280-
TORCH-COVDIF equipped with a Time-of-Flight sensor, the device has been
tested to be under the limits of a Class 1 Laser device.
8

9

Mounting Brackets
Accessory Product Number Illustration
Pivot mounting bracket DM100-PIVOTM-
01
Tilted angle pivot bracket DMBK-
DMPIVOT-00
Flat surface mounting plate adapter for Multi-Torch configuration 280-BKT-ADAPT
Mounting bracket with M3, M4 and 1/4 - 20 mounting holes BKT-INS-01
10

Accessory Product Number Illustration
Converter mounting bracket with M3 socket head screws/wrench ISB-7000-7K
Converter mounting bracket with Phillips flat head M3 screws and
M4 screws
ISB-7000-5K
11

Cables
Note: Cables are sold separately.
Accessory Product Number Illustration
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2001-xx (straight, xx specifies
length: 2m, 5m, 10m, 15m, 30m)
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2002-xx (right-angled, xx
specifies length: 2m, 5m, 10m)
Ethernet Cable, Robotic X-Coded M12-8 to
RJ-45
CCB-84901-2RBT-xx (straight, xx specifies
length: 2m, 5m, 10m)
X-Coded to A-Coded Ethernet cable adapter,
0.5 m
CCB-M12X8MS-XCAC
Power and I/O Breakout Cable, M12-12 to
Flying Lead
CCB-PWRIO- xx (straight, xx specifies
length: 5m, 10m, 15m)
Power and I/O Breakout Cable, M12-12 to
Flying Lead
CCB-PWRIO-xxR (right-angled, xx specifies
length: 5m, 10m, 15m)
I/O Module Cable M12-12 to DB15 CCB-PWRIO-MOD-xx (xx specifies length:
2m, 5m)
RS-232 Connection Cable CCB-M12xDB9Y-05
12

Accessory Product Number Illustration
I/O Extension Cable CKR-200-CBL-EXT
External Light Cable, Yellow
Note: This cable supports intensity
control.
IVSL-5PM12-J300
IVSL-5PM12-J500
IVSL-5PM12-J1000
IVSL-5PM12-J2000
External Light Cable, Black
Note: This cable supports intensity
control and is used with standard SVL
lights.
IVSL-M12-NSB-300
IVSL-M12-NSB-1000
IVSL-M12-NSB-2000
External Light Cable, Grey
Note: This cable does not support
intensity control.
CCB-M12LTF-xx (xx specifies length: 0.5m,
1m, 2m, 5m)
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2001-xx (straight, xx specifies
length: 2m, 5m, 10m, 15m, 30m)
Ethernet Cable, X-coded M12-8 to RJ-45 CCB-84901-2RBT-xx (straight, xx specifies
length: 2m, 5m, 10m)
Breakout Cable, M12-12 to Flying Lead CCB-PWRIO- xx (straight, xx specifies
length: 5m, 10m, 15m)
13

Setting Up Your In-Sight Vision System
Read this section to learn how the vision system connects to its standard
components and accessories.
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact
your Cognex Authorized Service Provider (ASP) or Cognex
Technical Support.
CAUTION:All cable connectors are keyed to fit the connectors on the vision
system. Do not force the connections or damage may occur.
Vision System Layout
The image and table below shows the elements of the vision system.
Number Description
1 Power I/O Breakout cable connector
14

Number Description
2Ethernet connector
3Illumination LEDs
4 Trigger button
Note: The Trigger Button is not supported.
5 Tune button
Note: The Tune Button is not supported.
6Indicator LEDs
7Power LED indicator
8 Train status/Trigger status LED indicator
9 Good/bad inspection LED indicator
10 Communication LED indicator
11 Error LED indicator
15

Dimensions
The following sections list dimensions of the vision system.
Note:
lDimensions are in millimeters and are for reference purposes only.
lAll specifications are for reference purposes only and can change
without notice.
In-Sight 2800 Mini with 6.2 mm lens
The following image shows the dimensions of In-Sight 2800, equipped with 6.2 mm
lens.
16

In-Sight 2800 Mini with 16 mm Lens
The following image shows the dimensions of In-Sight 2800 equipped with 16 mm
lens.
17

In-Sight 2800 Mini with 6.2 mm Lens - Right Angle
Configuration
The following image shows the dimensions of In-Sight 2800 equipped with L-
shaped extension and 6.2 mm lens.
18

In-Sight 2800 Mini with 16 mm Lens - Right Angle
Configuration
The following image shows the dimensions of In-Sight 2800 equipped with L-
shaped extension and 16 mm lens.
19

In-Sight 2800 with Multi Torch
The following image shows the dimensions of In-Sight 2800 equipped with Multi
Torch.
20