Cognex In-Sight 7000 Gen2 Series User manual

In-Sight®7000 Gen2 Series
Vision System
Reference Guide
2020 February 06
Revision: 5.8.1.2

Legal Notices
The software described in this document is furnished under license, and may be used or copied only in accordance with
the terms of such license and with the inclusion of the copyright notice shown on this page. Neither the software, this
document, nor any copies thereof may be provided to, or otherwise made available to, anyone other than the licensee.
Title to, and ownership of, this software remains with Cognex Corporation or its licensor. Cognex Corporation assumes
no responsibility for the use or reliability of its software on equipment that is not supplied by Cognex Corporation.
Cognex Corporation makes no warranties, either express or implied, regarding the described software, its
merchantability, non-infringement or its fitness for any particular purpose.
The information in this document is subject to change without notice and should not be construed as a commitment by
Cognex Corporation. Cognex Corporation is not responsible for any errors that may be present in either this document or
the associated software.
Companies, names, and data used in examples herein are fictitious unless otherwise noted. No part of this document
may be reproduced or transmitted in any form or by any means, electronic or mechanical, for any purpose, nor
transferred to any other media or language without the written permission of Cognex Corporation.
Copyright © 2017 - 2020. Cognex Corporation. All Rights Reserved.
Portions of the hardware and software provided by Cognex may be covered by one or more U.S. and foreign patents, as
well as pending U.S. and foreign patents listed on the Cognex web site at: cognex.com/patents.
The following are registered trademarks of Cognex Corporation:
Cognex, 2DMAX, Advantage, AlignPlus, Assemblyplus, CheckitwithChecker, Checker, CognexVisionforIndustry,
CognexVSOC, CVL, DataMan, DisplayInspect, DVT, EasyBuilder, Hotbars, IDMax, In-Sight, LaserKiller, MVS-8000,
OmniView, PatFind, PatFlex, PatInspect, PatMax, PatQuick, SensorView, SmartView, SmartAdvisor, SmartLearn,
UltraLight, VisionSolutions, VisionPro, VisionView
The following are trademarks of Cognex Corporation:
The Cognex logo, 1DMax, 3D-Locate, 3DMax, BGAII, CheckPoint, CognexVSoC, CVC-1000, FFD, iLearn, In-Sight
(design insignia with cross-hairs), In-Sight2000, InspectEdge, Inspection Designer, MVS, NotchMax, OCRMax,
PatMaxRedLine, ProofRead, SmartSync, ProfilePlus, SmartDisplay, SmartSystem, SMD4, VisiFlex, Xpand
Portions copyright © Microsoft Corporation. All rights reserved.
Portions copyright © MadCap Software, Inc. All rights reserved.
Other product and company trademarks identified herein are the trademarks of their respective owners.
2
Legal Notices

Regulations and Conformity
Note: For the most current CE declaration and regulatory conformity information, see the Cognex support site:
cognex.com/support.
Safety and Regulatory
Manufacturer Cognex Corporation
One Vision Drive
Natick, MA 01760 USA
In-Sight 7500/7500C: Regulatory Model 1AAB
In-Sight 7501/7501C: Regulatory Model 1AAB
In-Sight 7600/7600C: Regulatory Model 1AAB
In-Sight 7800/7800C: Regulatory Model 1AAB
In-Sight 7801/7801C: Regulatory Model 1AAB
In-Sight 7802/7802C: Regulatory Model 1AAB
In-Sight 7802P: Regulatory Model R00063
In-Sight 7900/7900C: Regulatory Model 1AAB
In-Sight 7901/7901C: Regulatory Model 1AAB
In-Sight 7902/7902C: Regulatory Model 1AAB
In-Sight 7902P: Regulatory Model R00063
In-Sight 7905/7905C: Regulatory Model R00063
This is a class A product. In a domestic environment this product may cause radio interference in
which case the user may be required to take immediate measures. This equipment complies with the
essential requirements of the EU Directive 2014/30/EU. Declarations are available from your local
representative.
EU RoHS Compliant to the most recent applicable directive.
FCC FCC Part 15, Class A
This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case
the user will be required to correct the interference at his own expense.
Korea In-Sight 7500/7500C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7501/7501C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7600/7600C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7800/7800C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7801/7801C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7802/7802C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7802P: Regulatory Model R00063: R-REM-CGX-R00063
In-Sight 7900/7900C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7901/7901C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7902/7902C: Regulatory Model 1AAB: MSIP-REM-CGX-1AAB
In-Sight 7902P: Regulatory Model R00063: R-REM-CGX-R00063
In-Sight 7905/7905C: Regulatory Model R00063: R-REM-CGX-R00063
This device is certified for office use only and if used at home, there can be frequency interference
problems.
3
Regulations and Conformity

Safety and Regulatory
TÜV In-Sight 7500/7500C: Regulatory Model 1AAB
In-Sight 7501/7501C: Regulatory Model 1AAB
In-Sight 7600/7600C: Regulatory Model 1AAB
In-Sight 7800/7800C: Regulatory Model 1AAB
In-Sight 7801/7801C: Regulatory Model 1AAB
In-Sight 7802/7802C: Regulatory Model 1AAB
In-Sight 7802P: Regulatory Model R00063
In-Sight 7900/7900C: Regulatory Model 1AAB
In-Sight 7901/7901C: Regulatory Model 1AAB
In-Sight 7902/7902C: Regulatory Model 1AAB
In-Sight 7902P: Regulatory Model R00063
In-Sight 7905/7905C: Regulatory Model R00063
NRTL: TÜV SÜD AM SCC/NRTL OSHA Scheme for UL/CAN 61010-1.
CB report available upon request. TÜV SÜD AM, IEC/EN 61010-1.
4
Regulations and Conformity

China RoHS
Hazardous Substances 有害物质
Part Name
部件名称
Lead (Pb)
铅
Mercury (Hg)
汞
Cadmium
(Cd)
镉
Hexavalent
Chromium
(Cr (VI))
六价铬
Polybrominated
biphenyls (PBB)
多溴联苯
Polybrominated
diphenyl ethers (PBDE)
多溴二苯醚
Regulatory
Model 1AAB
Regulatory
Model R00063
X O O O O O
This table is prepared in accordance with the provisions of SJ/T 11364.
这个标签是根据SJ / T 11364 的规定准备的。
O: Indicates that said hazardous substance contained in all of the homogeneous materials for this part is below the limit
requirement of GB / T26572 - 2011.
表示本部件所有均质材料中含有的有害物质低于GB / T26572 - 2011 的限量要求。
X: Indicates that said hazardous substance contained in at least one of the homogeneous materials used for this part is
above the limit requirement of GB / T26572 - 2011.
表示用于本部件的至少一种均质材料中所含的危害物质超过GB / T26572 - 2011 的限制要求。
For European Community Users
Cognex complies with Directive 2012/19/EU OF THE EUROPEAN PARLIAMENT AND OF THE COUNCIL of 4 July 2012
on waste electrical and electronic equipment (WEEE).
This product has required the extraction and use of natural resources for its production. It may contain hazardous
substances that could impact health and the environment, if not properly disposed.
In order to avoid the dissemination of those substances in our environment and to diminish the pressure on the natural
resources, we encourage you to use the appropriate take-back systems for product disposal. Those systems will reuse or
recycle most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product should not be disposed of along with municipal
waste and invites you to use the appropriate separate take-back systems for product disposal.
If you need more information on the collection, reuse, and recycling systems, please contact your local or regional waste
administration.
You may also contact your supplier for more information on the environmental performance of this product.
5
Regulations and Conformity

Precautions
To reduce the risk of injury or equipment damage when you install the Cognex product, observe the following
precautions:
lThe vision system requires a UL or NRTL listed power supply with a 24VDC output that meets the following rating
requirements:
lAt least 2A continuous current.
lA maximum short circuit current of less than 8A.
lA maximum power of less than 100VA and marked as a Limited Power Source (LPS) or National
Electrical Code (NEC) Class 2.
Any other voltage creates a risk of fire or shock and can damage the components. Applicable national and local
wiring standards and rules must be followed.
lThis product is intended for industrial use in automated manufacturing or similar applications.
lThe safety of any system incorporating this product is the responsibility of the assembler of the system.
lDo not install Cognex products where they are exposed to environmental hazards such as excessive heat, dust,
moisture, humidity, impact, vibration, corrosive substances, flammable substances, or static electricity.
lRoute cables and wires away from high-current wiring or high-voltage power sources to reduce the risk of
damage or malfunction from the following causes: over-voltage, line noise, electrostatic discharge (ESD), power
surges, or other irregularities in the power supply.
lDo not expose the image sensor to laser light. Image sensors can be damaged by direct, or reflected, laser light.
If your application requires laser light that might strike the image sensor, use a lens filter at the corresponding
laser wavelength. For suggestions, contact your local integrator or application engineer.
lThis product does not contain user-serviceable parts. Do not make electrical or mechanical modifications to
product components. Unauthorized modifications can void your warranty.
lChanges or modifications not expressly approved by the party responsible for regulatory compliance could void
the user’s authority to operate the equipment.
lInclude service loops with cable connections.
lEnsure that the cable bend radius begins at least six inches from the connector. Cable shielding can be
degraded or cables can be damaged or wear out faster if a service loop or bend radius is tighter than 10X the
cable diameter.
lThis device should be used in accordance with the instructions in this manual.
lAll specifications are for reference purposes only and can change without notice.
6
Precautions

Table of Contents
Legal Notices 2
Regulations and Conformity 3
China RoHS 5
For European Community Users 5
Precautions 6
Table of Contents 7
Symbols 9
Introduction 10
Support 10
Standard Components 10
Accessories 11
In-Sight Lenses, Lights and Covers 11
DataMan Lenses, Lights and Covers 18
External Lights 20
Cables 22
Mounting Brackets 23
I/O Modules 23
Connectors and Indicators 24
Installation 25
Install the Lens, Lighting and Cover 25
Install the C-Mount Lens and Cover (COV-7000-CMNT or COV-7000-CMNT-EX) 25
Install the C-Mount Lens and Cover (COV-7000-CMNT-LG) 27
Install the C-Mount Lens and In-Sight Illumination 28
Install the Autofocus Lens and In-Sight Illumination 33
Install the S-Mount/M12 Manual Focus Lens 39
Working Distance and Field of View (S-Mount/M12 Lenses) 41
Mount the Vision System 44
Install the Mounting Bracket (BKT-INS-01) 45
Install the Converter Mounting Bracket (ISB-7000-7K) 46
Install the Converter Mounting Bracket (ISB-7000-5K) 47
Connect the External Light Cable (Optional) 48
Connect the Ethernet Cable 48
Connect the Breakout Cable 49
Connect the CIO-MICRO I/O Module (Optional) 50
Connect the CIO-1400 I/O Expansion Module (Optional) 53
Replace the SD Card (Optional) 55
Replace the LED Ring Light (Optional) 56
Replace the M12 Autofocus Lens (Optional) 61
Specifications 69
7500 Series Vision System Specifications 69
7600 Series Vision System Specifications 72
7800/7801/7802 Vision System Specifications 75
7802P Vision System Specifications 78
7900/7901/7902 Vision System Specifications 81
7
Table of Contents

7902P/7905 Vision System Specifications 84
Acquisition Trigger Input 87
General-Purpose Inputs 88
High-Speed Outputs 89
High-Speed Output Wiring 90
External Light Connector 91
Ethernet Cable 92
Breakout Cable 93
I/O Module Cable 94
Dimensions 95
7500/7600 Series & 7800/7801/7802/7900/7901/7902 Vision System 95
7500/7600 Series & 7800/7801/7802/7900/7901/7902 Vision System with Cover (COV-7000-CMNT) 96
7500/7600 Series & 7800/7801/7802/7900/7901/7902 Vision System with Cover
(COV-7000-CMNT-EX) 97
7500/7600 Series & 7800/7801/7802/7900/7901/7902 Vision System with Illumination (ISLM-7000-xxx) 98
7802P/7902P/7905 Vision System 99
7802P/7902P/7905 Vision System with Cover (COV-7000-CMNT) 100
7802P/7902P/7905 Vision System with Cover (COV-7000-CMNT-EX) 101
7802P/7902P/7905 Vision System with Cover (COV-7000-CMNT-LG) 102
7802P/7902P/7905 Vision System with Cover (COV-7000-CMNT-LG) and Extender (COV-7000-
CMNT-LGX) 103
7802P/7902P/7905 Vision System with Illumination (ISLM-7000-xxx) 104
Mounting Bracket (BKT-INS-01) 105
Converter Mounting Bracket (ISB-7000-7K) 106
Converter Mounting Bracket (ISB-7000-5K) 107
C-Mount Lens Clearance Dimensions 108
Cleaning/Maintenance 109
Clean the Housing 109
Clean the Image Sensor Window 109
Clean the Cover 109
Appendix 110
Mechanical Vignetting 110
Remove the Illumination Accessory PCB 111
8
Table of Contents

Symbols
The following symbols indicate safety precautions and supplemental information:
WARNING:This symbol indicates a hazard that could cause death, serious personal injury or electrical shock.
CAUTION:This symbol indicates a hazard that could result in property damage.
Note: This symbol indicates additional information about a subject.
Tip: This symbol indicates suggestions and shortcuts that might not otherwise be apparent.
9
Symbols

Introduction
The In-Sight®vision system is a compact, network-ready, stand-alone machine vision system used for automated
inspection, measurement, identification and robot guidance applications on the factory floor. All models can be easily
configured remotely over a network using an intuitive user interface.
Support
Many information resources are available to help you use the vision system:
lThe In-Sight®Explorer Help and EasyBuilder Help files, provided with In-Sight Explorer software.
lOn-demand training: cognex.com/on-demand-training.aspx.
lThe In-Sight online support site: cognex.com/support/insight.
Standard Components
Note:
lCables are sold separately.
lIf a standard component is missing or damaged, immediately contact your Cognex Authorized Service
Provider (ASP) or Cognex Technical Support.
Component Description
Vision System Provides image acquisition, vision processing, job storage, Ethernet connectivity and discrete I/O. The
vision system has an 8GB SD card pre-installed.
10
Introduction

Accessories
You can purchase the following components separately. For a list of options and accessories, contact your local Cognex
sales representative.
In-Sight Lenses, Lights and Covers
The following In-Sight lenses, lights and covers are supported with the vision system.
C-Mount Standard and Extended Covers
Note:
lWhen using a C-Mount lens, the following restrictions apply:
lMaximum thread length is 5.25mm.
lThe C-Mount lens threads and body cannot protrude more than 6.5mm in length into the vision
system when screwed in unless the diameter of the back lens is smaller than 14.75mm. If the C-
Mount lens threads and body protrude more than 6.5mm, you can add a spacer between the lens
and vision system. However, the spacer decreases the working distance.
lRefer to C-Mount Lens Clearance Dimensions on page108 for more information.
CAUTION:If installing a C-Mount cover, the illumination accessory (ISLM-7000-xxx) PCB should not be installed to
the vision system. Refer to Remove the Illumination Accessory PCB on page111 for steps to safely remove the
PCB and avoid damage to the vision system.
Accessory Part Number Accessory Image
Standard plastic C-Mount cover and lens cover adapter.
Note: If using the COV-7000-CMNT cover, the maximum lens
length is 41mm, the maximum lens body diameter is 36.5mm
and the maximum diameter including locking screws is 47mm.
COV-7000-CMNT
Standard extended plastic C-Mount cover and lens cover adapter.
Note: If using the COV-7000-CMNT-EX cover, the maximum
lens length is 62mm, the maximum lens body diameter is
36.5mm and the maximum diameter including locking screws
is 46.5mm.
COV-7000-CMNT-EX
Wide plastic C-Mount cover and lens cover adapter. This accessory
is only supported with the In-Sight 7802P, 7902P and 7905 vision
system.
Note: If using the COV-7000-CMNT-LG cover, the maximum
lens length is 77mm, the maximum lens body diameter is
55mm and the maximum diameter including locking screws is
55mm.
COV-7000-CMNT-LG
Wide plastic 30mm C-Mount extender, compatible with the
COV-7000-CMNT-LG cover. This accessory is only supported with
the In-Sight 7802P, 7902P and 7905 vision system.
COV-7000-CMNT-LGX
11
Introduction

Accessory Part Number Accessory Image
Metal C-Mount lens cover adapter. Compatible with the following
In-Sight 5000 series metal C-Mount lens covers:
lLNS-CVR-EXT01
lLNS-CVR-R-00
lLNS-CVR-UV-00
lLNS-CVR50-AL-2
Note: If using the ADPT-MTL-M55 lens cover adapter, the
maximum lens diameter is 36.5mm. Locking screws cannot
protrude more than 7.0mm at the 36.5mm diameter. If they do,
the lens diameter must be reduced, so the maximum diameter
including locking screws is less than 50.5mm.
ADPT-MTL-M55
12
Introduction

C-Mount Illumination Accessories
Note:
lThe vision system supports connecting an integrated illumination accessory to the vision system's faceplate
and connecting an external light to the vision system's LIGHT connector, but does not support using both
lighting devices simultaneously.
lWhen using a C-Mount lens, the following restrictions apply:
lMaximum thread length is 5.25mm.
lThe C-Mount lens threads and body cannot protrude more than 6.5mm in length into the vision
system when screwed in unless the diameter of the back lens is smaller than 14.75mm. If the C-
Mount lens threads and body protrude more than 6.5mm, you can add a spacer between the lens
and vision system. However, the spacer decreases the working distance.
CAUTION:The following C-Mount lenses are supported with vision systems with 2.3 mega-pixel resolution and
below, when using the illumination accessory (ISLM-7000-xxx). If using a different C-Mount lens with the
illumination accessory, it must be 29.5mm in diameter or smaller. Maximum lens length is 38.5mm without a
bandpass filter and 36mm with a bandpass filter. Larger lenses will irreparably damage the vision system.
Accessory Part Number Accessory Image
9mm F1.4 aperture lens LFC-9F1B
12.5mm F1.4 aperture lens LFC-12.5F
16mm F1.4 aperture lens LFC-16F1
25mm F1.4 aperture lens LFC-25F1
35mm F1.6 aperture lens LFC-35F1
50mm F1.4 aperture lens LFC-50F1
Illumination accessory with white LED ring light, cover and hex wrench ISLM-7000-WHI
Illumination accessory with cover and hex wrench. Does not include an
LED ring light.
ISLM-7000-00
Diffuse cover COV-7000-DF
Clear cover COV-7000-CLR
Polarized cover
Note: When installing the cover, pull the red tab to remove the
protective film.
COV-7000-PL-FULL
13
Introduction

Accessory Part Number Accessory Image
Red LEDring light ISL-7000-RD
IR LED ring light ISL-7000-IR
Blue LED ring light ISL-7000-BL
White LED ring light
Note: For color vision systems, the white LEDring light should be
used.
ISL-7000-WHI
Red bandpass filter used with the ISL-7000-RD LEDring light ISF-7000-RDBP605
IR bandpass filter used with the ISL-7000-IR LED ring light ISF-7000-IRBP815
Blue bandpass filter used with the ISL-7000-BL LED ring light ISF-7000-BLBP435
14
Introduction

S-Mount/M12 Autofocus Accessories
Note:
lThe vision system supports connecting an integrated illumination accessory to the vision system's faceplate
and connecting an external light to the vision system's LIGHT connector, but does not support using both
lighting devices simultaneously.
lFor the In-Sight 7905, the vision system image circle is larger than the S-Mount/M12 lenses used in the
autofocus module (ISAF-7000-8mm)and the S-Mount/M12 adapter kit (ISLN-7000-SMNT), resulting in
mechanical vignetting in the image when using any S-Mount/M12 lens. Therefore, S-Mount/M12 lenses are
not recommended. For more information, see Mechanical Vignetting on page110.
Accessory Part Number Accessory Image
Autofocus module with 8mm S-Mount/M12 lens ISAF-7000-8mm
Lens removal tool with replacement lens nuts ISAF-7000-TOOL
6mm M12 lens LM12-06-01
8mm M12 lens LM12-08-01-F2.2
12mm M12 lens LM12-12-01-F2.3
16mm M12 lens LM12-16-01
25mm M12 lens LM12-25-01
Illumination accessory with white LED ring light, cover and hex wrench ISLM-7000-WHI
Illumination accessory with cover and hex wrench. Does not include an
LED ring light.
ISLM-7000-00
Diffuse cover COV-7000-DF
Clear cover COV-7000-CLR
Polarized cover
Note: When installing the cover, pull the red tab to remove the
protective film.
COV-7000-PL-FULL
15
Introduction

Accessory Part Number Accessory Image
Red LEDring light ISL-7000-RD
IR LED ring light ISL-7000-IR
Blue LED ring light ISL-7000-BL
White LED ring light
Note: For color vision systems, the white LEDring light should be
used.
ISL-7000-WHI
Red bandpass filter used with the ISL-7000-RD LEDring light ISF-7000-RDBP605
IR bandpass filter used with the ISL-7000-IR LED ring light ISF-7000-IRBP815
Blue bandpass filter used with the ISL-7000-BL LED ring light ISF-7000-BLBP435
16
Introduction

S-Mount/M12 Manual Focus Accessories
Note:
lThe following S-Mount/M12 lenses are supported. If a different lens is used, the following restrictions apply:
lAt infinity focus, the back focal length must be greater than 5.5mm.
lClose up, the back focal length of the lens cannot be greater than 13mm.
lThe DataMan clear cover accessory (DM300-CLCOV) is supported with In-Sight S-Mount/M12 manual focus
lenses and provides an IP65 rating.
lFor the In-Sight 7905, the vision system image circle is larger than the S-Mount/M12 lenses used in the
autofocus module (ISAF-7000-8mm)and the S-Mount/M12 adapter kit (ISLN-7000-SMNT), resulting in
mechanical vignetting in the image when using any S-Mount/M12 lens. Therefore, S-Mount/M12 lenses are
not recommended. For more information, see Mechanical Vignetting on page110.
Accessory Part Number Accessory Image
6mm M12 lens LM12-06-01
8mm M12 lens LM12-08-01-F2.2
12mm M12 lens LM12-12-01-F2.3
16mm M12 lens LM12-16-01
25mm M12 lens LM12-25-01
S-Mount/M12 adapter kit:
lS-Mount/M12 adapter
l13mm lens locking cone (P/N 1000000178)
l14mm lens locking cone (P/N 372-1270R)
lInstallation tool
Note: The S-Mount/M12 adapter kit (ISLN-7000-SMNT) is
required when installing In-Sight S-Mount/M12 manual focus
lenses.
ISLN-7000-SMNT
Clear cover DM300-CLCOV
17
Introduction

DataMan Lenses, Lights and Covers
The following DataMan accessories are also supported with the In-Sight vision system for S-Mount/M12 manual focus
lens configurations. DataMan lenses are only supported with DataMan lights and covers.
Note:
lThe following S-Mount/M12 lenses are supported. If a different lens is used, the following restrictions apply:
lAt infinity focus, the back focal length must be greater than 5.5 mm.
lClose up, the back focal length of the lens cannot be greater than 10 mm.
lFor the In-Sight 7905, the vision system image circle is larger than the S-Mount/M12 lenses used in the
autofocus module (ISAF-7000-8mm)and the S-Mount/M12 adapter kit (ISLN-7000-SMNT), resulting in
mechanical vignetting in the image when using any S-Mount/M12 lens. Therefore, S-Mount/M12 lenses are
not recommended. For more information, see Mechanical Vignetting on page110.
Accessory Part Number Accessory
Image
10.3mm M12 lens with locking (DM300-LENS-10) and 10.3 mm IR M12
lens with locking
DM300-LENS-10-IR
16mm M12 lens with locking DM300-LENS-16
25mm M12 lens with lens spacer and hex wrench (also requires
Extension kit)
DM300-LENS-25
Extension kit DM300-EXT
Clear cover DM300-CLCOV
Clear cover with white LED illumination DM300-CLCOV-WHI
Diffuse cover with red LED illumination DM300-DLCOV-RE
Diffuse cover with blue LED illumination DM300-DLCOV-BL
Diffuse cover with IR LED illumination DM300-DLCOV-IR
Polarized cover with red LED illumination DM300-PLCOV-RE
18
Introduction

Accessory Part Number Accessory
Image
Diffuse cover, red illumination (assembled), ESD safe DM300-DLCOV-RE-ESD
Polarized red LED high-powered integrated light, ESD safe DM360-HPIL-RE-P
Non-polarized red LED high-powered integrated light DM360-HPIL-RE
High-Power Illumination
Note: The following External Light Cables are supported with the Cognex high-power lights: IVSL-5PM12-J300,
IVSL-5PM12-J500, IVSL-5PM12-J1000 and IVSL-5PM12-J2000.
Accessory Part Number Accessory Image
Red narrow DM30X-HPIA3-625
Red wide DM30X-HPIA3-625-W
White narrow DM30X-HPIA3-WHI
White wide DM30X-HPIA3-WHI-W
Blue narrow DM30X-HPIA3-470
Blue wide DM30X-HPIA3-470-W
Infrared narrow DM30X-HPIA3-IR
Infrared wide DM30X-HPIA3-IR-W
19
Introduction

External Lights
External lights can be connected to the vision system's LIGHTconnector using the External Light cable.
Note:
lThe vision system supports connecting an integrated illumination accessory to the vision system's faceplate
and connecting an external light to the vision system's LIGHT connector, but does not support using both
lighting devices simultaneously.
lIf daisy-chaining multiple Cognex IVSL-YLW2X-xxx or IVSL-YLW300-xxx external lights:
lThe lights must be powered externally by a separate power supply.
lA Cognex control cable (CCB-FOV25-MAL-012) can be used to connect the vision system’s LIGHT
connector to the external light and a Cognex power cable (IVSL-5PM12-5) can be used to connect
the light to the separate power supply. Only the power and ground wires from the Cognex power
cable (IVSL-5PM12-5) should be connected to the remote power supply.
lIf using a Cognex IVSL-LX520-xxx external light:
lThe lights must be powered externally by a separate power supply.
lA Cognex control cable (CCB-FOV25-MAL-012) can be used to connect the vision system’s LIGHT
connector to the external light and a Cognex power cable (IVSL-5PM12-5) can be used to connect
the light to the separate power supply. Only the power and ground wires from the Cognex power
cable (IVSL-5PM12-5) should be connected to the remote power supply.
lThe following cables must not be used with IVSL-LX520-xxx external lights: IVSL-5PM12-J300,
IVSL-5PM12-J500 and IVS-5PM12-J1000, IVSL-5PM12-J2000.
lThe vision system supports Cognex IVSL-YL300-xx external lights with the following External Light cables:
IVSL-M12-NSB-300, IVSL-M12-NSB-1000 and IVSL-M12-NSB-2000.
Accessory Part Number Supported External Light Cables Accessory Image
Brick light, narrow blue IVSL-ODDM-S75-470 IVSL-5PM12-J300
IVSL-5PM12-J500
IVSL-5PM12-J1000
IVSL-5PM12-J2000
Brick light, narrow red IVSL-ODDM-S75-625 IVSL-5PM12-J300
IVSL-5PM12-J500
IVSL-5PM12-J1000
IVSL-5PM12-J2000
20
Introduction