Coway CHP-260L User manual

Water Filtration Device
CHP-260L/N
• This product can not be used if the voltage is dierent from that mentioned in the rating plate.
• For your safety and proper use of the product, please read this User’s Manual before use.
• Warranty card is included in this User’s Manual.

FEATURES
Optimal size and elegant design
This slim, elegant design ts into even narrow kitchen spaces,
making it convenient to use.
Energy-saving function using the light sensor
When Power Saving mode is set, the motor and heater
automatically run less often, reducing the amount of power
consumed.
Detachable water taps
The water taps can be separated for easy cleaning (turn them
clockwise to detach).
Convenient hot and cold/room water
continuous release functions
Push the Cup-Touch Lever for hot or cold/room water upward
to continuously dispense hot, cold or room water while the
lever is locked in place.
Dust-free ltering system
Comes equipped with a Plus Inno-Sense lter to minimize the
number of dust particles entering the storage tank.
Antibacterial system inside the water tank
An antibacterial lter is installed inside the product to prevent
the proliferation of microorganisms.
2
3
1
4
5
6

2
1
Thank you for using Coway Water Filtration Device.
Please read this Users’ Manual to use and maintain the product correctly.
If you encounter a problem while using the product, you may solve the problem referring
to the User’s Manual. As this manual contains the product warranty card, please keep it in a
safe place.
DEAR CUSTOMERS
- Please keep the User’s Manual where it can be readily reached or found -
CONTENTS
FEATURES / CONTENTS
Coway
2
1
| 03 |
SAFETY INFORMATION
Danger
Warning
Caution
| 07 |
PARTS NAME
| 08 |
WATER FILTRATION PROCESS
| 10 |
INSTALLATION PRECAUTIONS
| 12 |
INDICATION / OPERATION PART
| 15 |
HOW TO USE
To drink the cold water
To continuously dispense cold water
To drink the room water
To continuously dispense room water
To drink the hot water
To continuously dispense hot water
| 17 |
INSTALLATION
| 21 |
CLEANING METHOD
Storage tank
Gutter
Main body
Faucets
Cup-Touch Lever
| 25 |
FILTER REPLACEMENT
| 26 |
FILTER REPLACEMENT METHOD
| 27 |
TROUBLESHOOTING
| 28 |
SPECIFICATION
| 29 |
WATER FLOW DIAGRAM
| 33 |
WARRANTY CARD
FOR INFORMATION HOW TO USE
MAINTENANCE OTHERS

Danger : If not observed, serious injury or even death could
occur.
• Do not use a damaged power cord or plug, and loose outlet.
• Do not pull the power cord.
• Do not carry the unit by its power cord.
• Do not touch the power plug with a wet hand.
• Do not forcefully bend the power cord or put it under a heavy
object to prevent it from being damaged or deformed.
• Do not connect and pull out the power plug repeatedly.
• Remove any dust or water o in the pin and contacts of the
power plug.
• Do not plug into an outlet that is being used by several other
appliances.
Use an electrical outlet dedicated.
• When you don’t use for a long time, close the main water supply
valve and unplug.
• Do not attempt to repair or modify the power cord at your
discretion.
• In the case the power cord is damaged, do not replace the cord
yourself. Call Coway Service Center to have it replaced.
• Do not install near a heating device.
• When the water is coming inside of the product or there is a
puddle on the product, call Service Center after closing the
supplying valve and unplugging.
Be careful to keep this safety information.
Please read this information to prevent property loss
and ensure your safety. for 220 V - 240 V use only for 120 V use only
SAFETY INFORMATION

4
3
SAFETY INFORMATION |Danger
For Information
• If our product produces a strange noise or odd smell,
immediately unplug from the electrical outlet and call our
Service Center.
• Do not put the candle, a light for cigarette on the products.
• Do not place any containers with water, medicine, food, small
metallic objects, or any ammable material on the top of the
product.
• Clean after unplugging.

SAFETY INFORMATION
Warning : If not observed, serious injury or property damage
could occur.
• If the electric outlet is wet, carefully unplug the unit and let the
electric outlet completely dry before subsequent use.
• Unplug the product before repair, inspection, or parts
replacement.
• The water cooler is intended to be plugged into a receptacle of
the ground fault circuit interrupting type.
• Do not install the product on a sloped oor.
• Do not press the product by constraint or impact.
• Do not clean by spraying the water directly or don’t wipe the
product using the benzene and thinner.
• Do not repair, disassemble, or modify.
• This appliance is not intended for use by persons (including
children) with reduced physical, sensory or mental capabilities,
or lack of experience and knowledge, unless they have been
given supervision or instruction concerning use of the appliance
by a person responsible for their safety.
• Children should be supervised to ensure that they do not play
with the appliance.
• This appliance can be used by children aged from 8 years and
above.
• The new hose-sets supplied with the appliance are to be used
and that old hose-sets should not be reused.

6
5
SAFETY INFORMATION |Warning |Caution
For Information
Caution : If not observed, minor physical injury or property
damage may occur as a result.
• The ltration device installation shall comply with applicable
state and local regulations.
• Use after closing the water tank cover completely inside of the
product.
• To drink the ltered water, change the lter according to the
lter replacement cycle.
• When you don’t use for a long time, use after draining the saved
water completely and emptying the newly room water once
again.
• Do not allow hot water to come in contact with the human body.
• Do not use ltered water for the water exchange of an aquarium
or a shbowl.
• After moving the product or replacing the Plus Inno-sense lter,
the black powder can be remained in the inner bottom of the
water tank.
• Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or after
the system.
• Cleaning and user maintenance shall not be made by children
without supervision.

PARTS NAME
Inlet(Orange)
Outlet (Blue)
Front
Rear
Cold / Room water faucet
Cold / Room water
Changeover dial
Cold / Room water lever
Heatproof plate
Hot water faucet
Hot Water Safety button
Hot water lever
Cold water and hot water
temperature display
Light sensor
Water level indicator
Function selection button
and display
Power cord

8
7
WATER FILTRATION PROCESS
STEP 1, 2 : NEOSENSE FILTER
This neo-sense lter has the functions to remove particulates, dissolved organic and inorganic
impurities. It also has the function to remove chlorine, volatile organic compounds(VOC’s).
STEP 3 : RO MEMBRANE FILTER
RO membrane lter has the function to remove water contaminants such as heavy metals,
waterborne microorganisms and harmful organic chemicals etc.
The water concentrated the harmful material is owed out through the daily life water hose as the
daily life water.
STEP 4 : PLUS INNOSENSE FILTER
This Plus Inno-sense lter has the functions to remove smell induction material and to improve taste
of water.
STEP 5 : ANTIBACTERIAL FILTER*
This Antibacterial FIlter has the function to control microorganism propagation in water.
The 5-step water ltering system (CHP-260L)
The lter is the core technology of the ltration system.
If you don’t use qualifying lter or if you use an old lter that has expired, the system
performance may degrade.
Uses of reject water
- The reject water should be used for cleaning the restroom, the house,
clothes, or purposes other than drinking.
- Never use the reject water for a drinking or cooking.
Tips
PARTS NAME / WATER FILTRATION PROCESS
For Information
Reject
Water
Outlet
ANTIBACTERIAL
FILTER
NEOSENSE FILTER MEMBRANE FILTER RO PLUS INNOSENSE FILTER ANTIBACTERIAL FILTER

WATER FILTRATION PROCESS
STEP 1, 2 : NEOSENSE FILTER
This neo-sense lter has the functions to remove particulates, dissolved organic and inorganic
impurities. It also has the function to remove chlorine, volatile organic compounds(VOC’s).
SETP 3 : NANO-TRAP FILTER
The Nano-Trap Filter removes particulates, waterborne microorganisms, bacteria and virus in water.
SETP 4 : PLUS INNO-SENSE FILTER(D)
PLUS Inno-Sense Filter(D) reduces volatile organic compounds, odors and improves water taste.
STEP 5 : ANTIBACTERIAL FILTER*
This Antibacterial FIlter has the function to control microorganism propagation in water.
The 5-step water ltering system (CHP-260N)
The lter is the core technology of the ltration system.
If you don’t use qualifying lter or if you use an old lter that has expired, the system
performance may degrade.
ANTIBACTERIAL
FILTER
NEOSENSE FILTER NANOTRAP FILTER PLUS INNOSENSE
FILTERD
ANTIBACTERIAL FILTER

10
9
WATER FILTRATION PROCESS / INSTALLATION PRECAUTIONS
INSTALLATION PRECAUTIONS
1. Close main water supply valve to separate the faucet.
2. Apply the teon tape on the adaptor and t it to the
pipe.
3. Connect the faucet with the adaptor.
4. Connect 1/4 inch orange tubing with the connector
on the adaptor.
5. Open the feed valve to supply water to the ltration
system.
The summary for the proper installation of the water ltration device
Do not turn the water pipe.
Install the adaptor with connector to the cold water pipe.
Flush water through each lter at least 5 minutes before
Connection.
How to Use

• After installing the product
Get rid of the saved water above the full water in the inner water tank 2 times or more to use.
• When the indicator in the indication part is turned o
When the indicator in the indication part is turned o, check if the power supply was stopped
due to the power failure or other cause.
• Regular lter replacement
It is important to replace the lter regularly to maintain water quality as it is designed. If the lter
is overused beyond its service life, the performance of the water ltration device deteriorate. Do
not miss the lter replacement cycle.
• When you didn’t use for a long time
If you saved the water for a long time or you didn’t use, drain the water inside of the water
ltration device completely and remove the newly ltered water one time to use.
• When you don’t want to use the product for a long time.
Close the main water supply valve and unplug the power cord.
When you don’t use for a long time, close the main water supply valve and
unplug the power cord.
Tips
Please check before use!
Only connect the power cord to the voltage rating that matches it on
the rating plate.
INSTALLATION PRECAUTIONS

12
11
INSTALLATION PRECAUTIONS / INDICATION / OPERATION PART
How to Use
Indication part
INDICATION / OPERATION PART
5
Power Saving Mode
indicator
This indicator is illuminated when
Power Saving Mode is selected.
3
Water level indicator
The indicator is illuminated when
the water level in the interior tank
gets low.
4 Light sensor
This sensor detects light around the
purier to decide whether it is day
or night.
1
Hot Water function on and
hot water temperature
indicator
The indicator lights are illuminated
according to the temperature of
the hot water. The more lights are
illuminated, the hotter the water
(three stages).
∗When power is connected to the
purier, the indicator is illuminated
to show whether or not the Hot Water
function is on.
2
Cold Water function on and
cold water temperature
indicator
The indicator lights are illuminated
according to the temperature of
the cold water. The more lights
are illuminated, the cold the water
(three stages).
∗When power is connected to the
purier, the indicator is illuminated to
show whether or not the Cold Water
function is on.
1
Hot Water function
on and Hot Water
Temperature Indicator
4
Light sensor
3
Water level indicator
5
Power Saving Mode
Indicator
2
Cold Water function
on and Cold Water
Temperature Indicator

Operation part
2
Hot Water function
selection button
Use this to select/cancel selection of
the hot water function.
Hold the button for 2 seconds or
more and the indicator lights up.
∗The Hot Water function is not on
initially, and when power is turned o,
the product's most recent settings are
kept.
5
Cold- Room Water Selection
dial
Use this to select cold water or room
water.
1
Power Saving function
selection button
Use this to select/cancel selection of
Power Saving Mode.
Hold the button for 2 seconds or
more and the indicator lights up.
∗The Power Saving function is not on
initially (When power is connected to
the purier, the Power Saving function
is not set).
3
Cold Water function
selection button
Use this to select/cancel selection of
the cold water function.
Hold the button for 2 seconds or
more and the indicator lights up.
∗The Cold Water function is not on
initially, and when power is turned o,
the product's most recent settings are
kept.
4
Hot Water Safety button
Press once before dispensing water.
If the Hot Water Safety button is
not pressed, hot water cannot be
dispensed even if the Cup-Touch
Lever is pushed.
4
Hot Water
Safety button
1
Power Saving
function
selection button
2
Hot Water Mode
selection button
3
Cold Water Mode
selection button
5
Cold - Room Water
Selection dial
INDICATION / OPERATION PART

14
13
How to Use INDICATION / OPERATION PART
■To use the Cold Water function
Press the Cold Water button for 2 or more seconds and check
that the Cold Water function is illuminated on the display
and the Cold Water Temperature Indicator is illuminated.
To turn o the Cold Water function, press the Cold Water
function button for 2 or more seconds again.

You can get cold water about 30 minutes after you turn on
the cold water function.
■ To use the Hot Water function
Press the Hot Water button for 2 or more seconds and check
that the Hot Water function is illuminated on the display and
the Hot Water Temperature Indicator is illuminated.
To turn o the Hot Water function, press the Hot Water
function button for 2 or more seconds again.

You can get hot water starting about 30 minutes after you
turn on the hot water function.
■To use the Power Saving function
Hold the Power Saving button for 2 seconds or more to turn
on the Power Saving function.
The Power Saving indicator blinks when it detects that it is
night.

If the Power Saving indicator is lit, the cold water
temperature will be kept warmer when the area around
the purier is dark.
- If cold water is not released from the water purier, check that the Cold Water
Mode indicator is lit up on the display (see p. 11).
- When the level of room water inside the water tank is low, you may not be
able to get as much water as usual.
- When there is a power failure or the power cord is reconnected, the machine
is reset to its most recent settings.
- This product has a Power Saving function when not in use. If it is not used for
a long time (about 9 hours), the hot water temperature is automatically kept
lower and the cold water temperature higher to help reduce electricity costs.
When in Power Saving mode when not in use, hot water may be cooler and
cold water warmer than usual.
Tips
2 seconds2 seconds2 seconds
2 seconds2 seconds2 seconds
2 seconds2 seconds2 seconds

To dispense continuous cold water
HOW TO USE
▶ ▶
▶ ▶
Press the Cold Water button and check that the Cold Water indicator is lit on the display.
Turn the Cold Water - Room Water Selection dial to the
right and push the touch lever.
Press the Cold Water button and check that the Cold Water indicator is lit on the display.
Turn the Cold Water - Room Water Selection dial to the
right and move the Cup-Touch Lever upward to lock the
lever in place.
- If cold water is not dispensed from the water purier, check that the Cold
Water indicator is lit up on the display (see p. 11).
Tips
To drink the cold water

16
15
HOW TO USE
How to Use
▶ ▶
▶ ▶
Turn the Cold Water - Room Water Selection dial to the
left and push the Cup-Touch Lever.
Turn the Cold Water - Room Water Selection dial to the
left and move the Cup-Touch Lever upward to lock the
lever in place.
To dispense continuous room water
- If cold water is not dispensed from the water purier, check that the Cold
Water indicator is lit up on the display (see p. 11).
Tips
To drink the room water

▶
▶
Press the Hot Water Safety button and push the Cup-
Touch Lever. Press the Hot Water function selection
button and check that the Hot Water indicator is lit.
Push the Hot Water Safety button once more.
- If hot water is not dispensed from the water purier, check that the Hot
Water indicator is lit up on the display (see p. 11).
- Beware of burns when using the Hot Water function.
Tips
Press the Hot Water Safety button and move the Cup-
Touch Lever upward to lock the lever in place.
Press the Hot button and check that the Hot Water
indicator is lit on the display.
To drink the hot water
To dispense continuous hot water
HOW TO USE

18
17
HOW TO USE / INSTALLATION
Connect the orange color inlet tubing 1to the tap
water supplying pipe. Connect the outlet tubing 2.
1
2
INSTALLATION
Follow the instruction for installation (CHP-260L)
Main water
supply valve
voltage rating that
matches it on the
rating plate.
Inlet tubing (Orange)
Inlet tubing (Orange)
Outlet tubing(Blue)
Outlet tubing(Blue)
Maintenance

Connect the orange color inlet tubing 1to the tap
water supplying pipe.
1
INSTALLATION
Main water
supply valve
voltage rating that
matches it on the
rating plate.
Inlet tubing (Orange)
Inlet tubing (Orange)
Follow the instruction for installation (CHP-260N)