Cree OSQ Series User manual

OSQ Series
LED Area Light
Transportation Mount
1 of 3 LPN00598X0001A0_A
INSTALLATION INSTRUCTIONS
INSTRUCTIONS D’INSTALLATION
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should
always be followed including the following:
READ AND FOLLOW ALL SAFETY
INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant
l’installation.
2. This luminaire must be installed in accordance with the NEC or
your local electrical code. If you are not familiar with these codes
and requirements, consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n’êtes pas familier avec ces codes et ces
exigences, veuillez contacter un électricien qualié.
SAVE THESE INSTRUCTIONS FOR
FUTURE REFERENCE
DIRECT MOUNT
STEP 1:
Install grommet into rear mounting bracket. Orient
grommet as shown in Figure 1.
STEP 2:
Route power cord from luminaire through grommet in
rear mounting bracket. See Figure 1.
STEP 3:
Slide the rear mounting bracket into the luminaire
housing. See Figure 1.
STEP 4:
Tighten (4) 3/8-16 socket head set screws located
on the luminaire housing to 85 in-lbs (9.6 N-m). See
Figure 1.
STEP 5:
Align front plate with luminaire housing and insert
U-bolt. U-bolt position is dependent on luminaire size.
See Figure 2 and 3.
STEP 6:
Install (2) 1/4-20 nuts with integral lock washer
onto U-bolt. The lockwasher should be against the
mounting plate. Torque to 60 in-lbs (7 N-m). See
Figure 2.
STEP 7:
Install (2) 1/4-20 lock nuts and torque to 120 in-lbs
(14 N-m) while holding the nuts installed previously in
Step 7 to prevent rotation. See Figure 2.
TO INSTALL:
1
2
Rear Mounting
Bracket
Socket Head Set Screws
Front Plate
U-Bolt
Rear Mounting
Bracket
Grommet
Grommet
Nuts
Lock Nuts
• First 2 holes for OSQ Large
Luminaires
• Second 2 holes for OSQ Medium
luminaires
NOTES:
• Before installing, ensure the mounting surface and
securement points are structurally sound and capable of
supporting the weight of the luminaire.
• DO NOT lift the luminaire by the cord.

2 of 3 LPN00598X0001A0_A
STEP 8:
Place (4) 3/8-16 carriage bolts into top plate slots. Bolt locations are
dependent on luminaire size, see Figure 4. Align the top plate on an
appropriate mounting surface. Using customer supplied 3/8” stainless
steel or coated bolts and washers, secure the bracket to the mounting
surface. See Figure 4 and 5.
STEP 9:
Secure luminaire to top plate using (4) 3/8” washers and (4) 3/8-16
nuts. Torque nuts to 240 in-lbs (27 N-m). See Figure 6.
STEP 10:
Insert luminaire cord into customer supplied junction box with suitable
Listed cord strain relief.
STEP 11:
Connect the cord to the supply wiring per the Electrical Connections
section on the last page.
3
5
U-Bolt Position
OSQ MEDIUM OSQ MEDIUM
OSQ LARGE
OSQ LARGE
Bolt Locations
4
10.00 in
7.00 in
11.10 in
Mounting Holes for 3/8" Fasteners 6
(4) Washers and Nuts
Top Plate

3 of 3 LPN00598X0001A0_A
www.lighting.cree.com
© 2018 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change.
See http://lighting.cree.com/warranty for warranty and specifications. Cree®is a registered trademark, and the Cree logo is a
trademark of Cree, Inc. NEMA® is a registered trademark of the National Electrical Manufacturers Association.
ELECTRICAL CONNECTIONS
STEP 1:
Using Listed 90°C minimum rated wire connectors make the following
electrical connections within the pole:
a. For 120/277/347V connect the black fixture lead to the voltage
supply or Hot 1 (for 208/240/480V wiring).
b. For 120/277/347V connect the white fixture lead to the neutral
supply or Hot 2 (for 208/240/480V wiring).
c. Connect the green or green/yellow ground lead to ground.
d. If Dimming is an option; connect the violet dimming positive lead
to the supply dimming positive lead.
e. If Dimming is an option; connect the grey dimming negative lead
to the supply dimming negative lead.
LINE
OR HOT 1
GREEN
LINE-BLACK
GROUND-GREEN
NEUTRAL-WHITE
DIM (-) GREY
DIM (+) VIOLET
NEUTRAL
OR HOT 2
VIOLET
GREY
SUPPLY WIRING
(DIMMING OPTIONAL)
LUMINAIRE
DRV DRV CRTL
1 2 3 4 5
9123
4
5
6
7
8
8
Luminaire Cover Door
7
FIELD ADJUSTABLE DIMMING - (OPTIONAL)
NOTE: This luminaire may be provided with field
adjustable dimming. If so, luminaires leave the
factory adjusted to the maximum setting specified
when ordered. Visit the product specification sheet
for lumen and power multipliers for each field
adjustable output dim setting..
STEP 1:
The Dimming module is located inside the luminaire.
Open the luminaire door cover by loosening the (5)
screws. See Figure 7.
STEP 2:
Establish the desired input power multiplier by
referring to the product dimming spec sheet and turn
the switch to the correlating position
STEP 3:
Adjust the Dimming Module, see Figure 8, to the
selected position and reinstall the cover ensuring no
wires are pinched.