Cree LS8 User manual

LS Series
LED Surface Ambient Luminaire with Through-Wiring/Quick-Connects
Includes: LS4 and LS8
INSTALLATION INSTRUCTIONS
1 of 2
LPN00434X0001A0_B
TO INSTALL:
NOTES:
• Available luminaire length are 4' and 8'.
• Suitable for Damp Locations
• Designed for use in 120-277V 60Hz protected circuit
(fuse box, circuit breaker). Supply wire size as per
NEC or governing code(s), 90C rated.
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be
followed including the following:
READ AND FOLLOW ALL
SAFETY INSTRUCTIONS
1. DANGER- Risk of shock- Disconnect power before installation.
DANGER – Risque de choc – Couper l’alimentation avant
l’installation.
2. This luminaire must be installed in accordance with the NEC or your
local electrical code. If you are not familiar with these codes and
requirements, consult a qualied electrician.
Ce produit doit être installé conformément à NEC ou votre code
électrique local. Si vous n’êtes pas familier avec ces codes et ces
exigences, veuillez contacter un électricien qualié.
SAVE THESE INSTRUCTIONS
FOR FUTURE REFERENCE
1
2
Push The Connected
Connectors Inside
Luminaire
LUMINAIRE INSTALLATION
STEP 1:
Attach LS luminaire to mounting surface.
STEP 2:
Attach the connectors from adjoining luminaires
and push the connection into the luminaire. See
Figure 1.
STEP 3:
Push the two adjoining luminaires against each
other as shown in Figure 2.

2 of 2
LPN00434X0001A0_B
www.cree.com/canada
© 2016 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change.
See www.cree.com/canada for warranty and specifications. Cree®is a registered trademark, and the Cree logo is a
trademark of Cree, Inc.
ELECTRICAL CONNECTIONS
STEP 1:
Make the following Electrical Connections:
For 120-277V applications make the following Electrical
Connections:
a. Connect the black luminaire lead to the line supply
lead
b. Connect the white luminaire lead to the neutral supply
lead
c. Connect the green or green/yellow ground lead to the
supply ground lead
d. If Dimming is an option; connect the violet dimming
positive lead to the supply dimming positive lead. If
dimming is not being used, ensure to cap off the violet
lead.
e. If Dimming is an option; connect the grey dimming
negative lead to the supply dimming negative lead. If
dimming is not being used, ensure to cap off the grey
lead.
GREEN
LINE-BLACK
GROUND-GREEN
NEUTRAL-WHITE
(DIMMING OPTIONAL)
DIM (-) GREY
DIM (+) VIOLET VIOLET
GREY
SUPPLY WIRING
LUMINAIRE
NEUTRAL OR HOT 2
LINE OR HOT 1
3
Joint Aligner
(4) Supplied Screws
4
Plastic Knockout Covers
STEP 4:
Place the Joint Aligner (LS-RJ) over the two
adjoining luminaires. Line up the mounting holes
on the bracket with those on the luminaire. See
Figure 3. Secure the Joint Aligner by inserting
the (4) supplied screws as Shown in Figure 3.
STEP 5:
Continue Steps 1-4 until all luminaires are
installed.
STEP 6:
On the last luminaire in the row, push the
connector into the luminaire and insert (2) plastic
knockout covers as shown in Figure 4.
STEP 7:
Make wiring connections per “ELECTRICAL
CONNECTION” section, to the first luminaire
in row. Cut off plug and make wire connections
inside luminaire end with dimming wire
compartment. Dimming connections must be
made in the dimming compartment (See Figure
5), line connections made outside compartment.
End Cap Wiring Knockouts
Dimming Wire
Compartment
5