Cree ESSENTIA AE Series User manual

1 of 2 LPN00334X0001A0_A
LED TRACK-BEVELED CYLINDER
INSTALLATION INSTRUCTIONS
S-CT-BVLCYL-10L
IMPORTANT SAFEGUARDS
When using electrical equipment, basic safety precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS
1. To avoid the possibility of electrical shock turn off power supply before installation or servicing.
2. This luminaire must be installed in accordance with the NEC or your local electrical code. If you are not familiar with these
codes and requirements, consult a qualied electrician.
3. Essentia® by Cree Track xtures are UL® Classied for use with Essentia by Cree “CT” track systems, and Juno® (not afliated
with Essentia by Cree) “T” and “TU” Series track systems only.
4. MIN. 90°C SUPPLY CONDUCTORS.
5. Wait until xture has cooled down before installing or servicing the xture.
6. Please read and understand all instructions thoroughly before installing any part of the Track system.
SAVE THESE INSTRUCTIONS FOR FUTURE REFERENCE
NOTES:
1. All Essentia® Track sections are manufactured with a Polarity Groove.
2. All Essentia® Track xtures are manufactured with Indicator Arrows designed to point toward the Polarity Groove once
installed. See Figures 1 and 2.
3. All Essentia® Track xtures are supplied with a Contact Support to convert xture from Single Circuit installation to Two Circuit
Installation. See Figures 3.
DIMMING INFORMATION:
For a list of approved dimmers visit lighting.cree.com.
STEP 1
• Insert Brass Contact on top of Track Adaptor into the Track Channel.
See Figures 1 and 3.
STEP 2
• Rotate the Track Adaptor 90° so that the Indicator Arrows point
toward the Polarity Groove once installed. See Figure 2. Pull Adaptor
Latch down as you rotate Track Adaptor in order for Latch to clear
track edge and allow it to snap into place in the track.
STEP 3
• To remove or relocate track fixture location, pull Adaptor Latch down,
rotate the Track Adaptor 90° away from the Polarity Groove and
remove.
FIXTURE INSTALLATION – SINGLE CIRCUIT TRACK
2
Plastic
Insulator
Polarity
Groove
Copper
Conductors
Aluminum Track
Extrusion
1
Track Adapter
Indicator Arrows
Luminaire

2 of 2 LPN00334X0001A0_A
© 2016 Cree, Inc. All rights reserved. For informational purposes only. Content is subject to change.
See lighting.cree.com/warranty for warranty and specifications. Cree®and Essentia®are registered
trademarks of Cree, Inc.
US: lighting.cree.com T [phone] F [phone]
Canada: www.cree.com/canada T [phone] F [phone]
FIXTURE INSTALLATION – TWO CIRCUIT TRACK
STEP 1
• To install track fixture into lower circuit of two-circuit track,
follow directions for single circuit installation.
STEP 2
• To install track fixture into upper circuit of two-circuit track,
raise the Brass Contact labeled “P” by grasping Contact with
needle nose pliers and pulling up into position. See Figure 3.
STEP 3
• Insert Contact Support by tipping and positioning it under the
“P” Contact. See Figure 3. Snap Contact Support in place.
NOTE: Once the contact support is in place, make sure the “P”
contact is fully seated in the support by using the needle nose
pliers to push the “P” contact into place.
STEP 4
• Refer to instructions 1-3 under “Fixture Installation on Single
Circuit Track” section.
Movable Brass
Contact “P”
Contact
Support
INSTALLATION OF OPTIONAL LENS
STEP 1
• Before attempting Optical Lens addition, remove fixture from
track.
STEP 2
• Place chosen lens on top of reflector. The lens has a step
around the perimeter, the larger diameter at the step should be
toward reflector. See Figure 4.
Note: Clear lens is used for protection and frosted lens provides
a more diffuse beam spread.
STEP 3
• Gently push the lens against the latches on all four sides. See
Figure 5.
STEP 4
• Reinstall xture onto track.
3
4
5