Crestron TSW-1050 Dimensional drawing

DO GUIDE
TSW-1050
10.1” Touch Screen
DO Install the Touch Screen
The Crestron®TSW-1050 touch screen installs easily over a
standard 2-gang or 3-gang U.S. electrical box or a 2-gang
European electrical box. It can also be attached directly
to drywall and other surfaces over the front of a 2 3/8” (60
mm) high by 3 3/8” (86 mm) wide cutout. When installed, the
touch screen protrudes just 1/2” (13 mm) from the mounting
surface and is magnetically adhered to its mounting bracket,
eliminating any visible screws for an ultra clean appearance.
To mount the TSW-1050 into an electrical box, use the
following procedure:
1. Use four of the eight included screws (four 06-32 x
3/4” or four 3 x 16 mm screws) to attach the mounting
bracket to the electrical box, as shown in the following
illustrations.
NOTE: For U.S.-style installations, use a #2 Phillips
screwdriver. For European-style installations, use a #1
Phillips screwdriver or equivalent.
For U.S.-style installations, use the 06-32 x 3/4” screws.
For European-style installations, use the 3 x 16 mm
screws.
2. Make connections to the TSW-1050 using Crestron
power supplies for Crestron equipment. Power and data
connection to the TSW-1050 is provided by a single
Ethernet cable connected to the LAN port at the rear of
the unit. A Crestron PoE power supply or PoE-capable
network switch is recommended (both sold separately).
Apply power after the Ethernet cable is connected.
Hardware Connection for the TSW-1050
3. Carefully hold the touch screen over the mounting
bracket and gently place it in position. The magnets
on the rear of the touch screen hold it in place on the
mounting bracket.
DO Access the Setup Screen
NOTE: The TSW-1050 can take up to 120 seconds to boot.
When power is applied for the rst time, the screen shown in
the following illustration appears.
Touch the Setup button to display the TSW-1050 Setup
screen. The buttons on the Setup screen enable basic
conguration prior to regular operation of the TSW-1050.
DO Check the Box
QTY PRODUCT PART NUM.
1Metal Mounting Bracket 2034503
4 Screws, 06-32 x 3/4" 2033247
4 Screws, 3 x 16 mm 2013788
2 Screws, M3.5 x 25 mm 2023756
Mounting Bracket
Screws (4) 06-32 x 3/4”
TSW-1050
U.S. Electrical Box
Mounting Bracket
Screws (4) 3 x 16 mm
TSW-1050
European Electrical Box
Reset Button
LAN PoE:
10BASE-T / 100BASE-TX
Ethernet to LAN

DO GUIDE DOC. 7757A (2043273) 02.15
Specications subject to change without notice.
NOTE: During regular operation of the touch screen, there are two ways to activate the setup
functions:
1. Place a button on the project main page and assign the reserved join number (17242) that
activates setup.
2. Touch the hard keys labeled below as 1, 2, 3, and 4 in sequence twice (touch 1, 2, 3, 4, 1, 2,
3, 4) within a 5 second period.
NOTE: For details on conguring the TSW-1050, refer to Doc. 7366 at
www.crestron.com/manuals.
DO Learn More
Visit the website for additional information and the latest rmware updates.
Crestron Electronics
15 Volvo Drive, Rockleigh, NJ 07647
888.CRESTRON | www.crestron.com
As of the date of manufacture, the product has been tested and found to comply with specications for CE marking.
Federal Communications Commission (FCC) Compliance Statement
This device complies with part 15 of the FCC Rules. Operation is subject to the following conditions:
(1) This device may not cause harmful interference and (2) this device must accept any interference received, including interference
that may cause undesired operation.
CAUTION: Changes or modications not expressly approved by the manufacturer responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not
occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
Industry Canada (IC) Compliance Statement
CAN ICES-3(B)/NMB-3(B)
Crestron product development software is licensed to Crestron dealers and Crestron Service Providers (CSPs) under a limited non-exclusive, non-transferable Software Development Tools
License Agreement. Crestron product operating system software is licensed to Crestron dealers, CSPs, and end-users under a separate End-User License Agreement. Both of these Agreements
can be found on the Crestron website at www.crestron.com/legal/software_license_agreement.
The specic patents that cover Crestron products are listed at patents.crestron.com. The product warranty can be found at www.crestron.com/warranty.
Crestron and the Crestron logo are either trademarks or registered trademarks of Crestron Electronics, Inc. in the United States and/or other countries. Other trademarks, registered trademarks,
and trade names may be used in this document to refer to either the entities claiming the marks and names or their products. Crestron disclaims any proprietary interest in the marks and names
of others. Crestron is not responsible for errors in typography or photography.
This document was written by the Technical Publications department at Crestron.
©2015 Crestron Electronics, Inc.
1
2
3
4