Cross Technologies 1584-29 User manual

Instruction Manual Model 1584-29
RF Splitter
March 2019 Rev. C
+DC
MONITOR 1
GND ON RF +DC
MONITOR 2
GND ON RF
MODEL
1584
POWER DIVIDER
CROSS TECHNOLOGIES INC.
VOLTAGE VOLTAGE
A B
AC POWER
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]

INSTRUCTION MANUAL
MODEL 1584-29 RF Splitter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
1.3 Environmental Use Information 5
2.0 Installation 6
2.1 Mechanical 6
2.2 Rear Panel Input/Output Connectors 7
2.3 Front Panel Monitors and Indicators 7
2.4 Operation 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are not other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
1584-29 Manual, Rev C Page 2 3/7/19

MODEL 1584-29 RF Splitter
1.0 General
1.1 Equipment Description - The Model 1584-29 is two, nine way, 0.95 - 2 GHz, 0 dB gain splitters in a 1
Rack Unit chassis with redundant 100-240 ±10% VAC power supplies. Each splitter provides fused DC power
insertion on the input connector center pin, surge protection, and excellent RF characteristics. Each splitter has a
monitor connector on the front panel and eight outputs on the back panel. Two individual 90-260 VAC input power
supplies provide a diode OR’d + 22 VDC voltage for internal amplifiers and for DC to power external amplifiers
(often Low Noise Block converters or LNBs) through DC power inserters. Each LNB power line is separately
fused. A surge suppressor on each splitter input protects against high voltage transients. All splitter outputs are AC
coupled so no DC appears on their center conductors. On the front panel, green LEDs indicate presence of +22
VDC at each LNB power supply output and DC voltage test points allow monitoring this voltage with a voltmeter.
Presence of power from the +24 VDC power supplies is shown by the AC Power A and B green LEDs.
+DC
MONITOR 1
GND ON RF +DC
MONITOR 2
GND ON RF
MODEL
1584
POWER DIVIDER
C ROSS
T ECHNOLOGIES INC.
VOLTAGE VOLTAGE
A B
AC POWER
FRONT PANEL
AC A AC B
GND
JIJ2J3J4
J
19 J5J6J7J8
J
9J10J11J12
J17 J13J14J15J16 OUTOUTOUTOUTIN OUTOUTOUT
O
UTOUTOUTOUTOUTIN OUTOUTOUTOUT
FUSE F4 FUSE F3
REAR PANEL
FIGURE 1.1 MODEL 1584-29 FRONT AND REAR PANELS
AMP
DC
INS
SURGE
SUP-
PRESOR
FUSE
9 WAY
SPLIT
OUT 1
OUT 2
OUT 8
MON
LNB PWR LED
1584-29 BLOCK DIAGRAM, EACH SPLITTER
1 - 2
GHz
IN
1 - 2 GHz OUT
LNB PWR TP
FIGURE 1.2 MODEL 1584-29 RF SPLITTER BLOCK DIAGRAM
1584-29 Manual, Rev C Page 3 3/7/19

1.2 Technical Characteristics
TABLE 1.0 1584-29 RF SPLITTER SPECIFICATIONS
Characteristics Specifications*
Input Characteristics
Input Impedance/RL 75 Ω/10dB, min, 0.95-2.05 GHz;
14dB, typ, 0.95-1.75 GHz
Input Level -20 dBm total maximum
Output Characteristics
Impedance/RL 75 Ω/10dB, min, 0.95-2.05 GHz;
14 dB, typ, 0.95-1.75 GHz
In-Band Characteristics
Gain +0 dB ± 1.0 dB
Frequency Response ± 1.0 dB, 0.95 - 1.75 GHz; ± 0.5 dB, any 20 MHz incr.
+1, -3 dB,1.75 - 2 GHz; ± 0.7 dB, any 20 MHz incr
Port to Port Isolation > 18 dB, min., 20 dB typ.
Coupler to Coupler Isol. > 35 dB, min., 40 dB typ
Indicators
Power Green LED indicates DC voltage prior to diode OR and to amplifiers
Other
LNB DC voltage 22 ± 2 VDC
Output Amplifier current 300 ma, max., each
Surge Suppressor SiDACTOR
RF connectors Type F , female
Fuses - AC 5mm, 2 amp, fast blo
Fuses - LNB Voltage 1/4 “, 1 amp, fast blo
AC Power Redundant power supplies, 100-240 ±10% VAC, 50 -60 Hz, 30 watts max.
Mechanical 19 inch standard chassis 1.75”high X 12” deep
Options
Option D 50ΩBNC RF IN/OUT
*+10 to +40 degrees C; 2000 meters max elevation; 80% max humidity; Pollution Degree 2; Specifications
subject to change without notice.
1584-29 Manual, Rev C Page 4 3/7/19

1.3 Environmental Use Information
A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C.Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used, when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connection to the Branch
(use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
1584-29 Manual, Rev C Page 5 3/7/19

2.0 Installation
2.1 Mechanical - The 1584-29 consists of one RF printed circuit board (PCB) housed in a 1 RU (1 3/4 inch
high) by 12 inch deep chassis. Redundant, switching, +24 VDC power supplies with the DC output diode OR’d
provide redundant power for the internal and external amplifiers and LEDs. Connectors are type F, female for the
RF connections. The 1584-29 can be secured to a rack using the 4 holes on the front panel. Figure 2.1.shows how
the 1584-29 is assembled. J27 and J25 connect DC Power to the fuses as shown and J30 and J29 connect the DC
voltage from the power supplies to the PCB as shown.
POWER
SUPPLY B
POWER
SUPPLY A
1
2
J27
LNB-1 FUSE
PIN 1, LNB SIDE
PIN 2, +22 VDC SIDE
1
2
J25
2 1
J30
+24, PS B IN
PIN 1, +24 VDC
PIN 2, GROUND
2 1
J29
LNB-2 FUSE
PIN 1, LNB SIDE
PIN 2, +22 VDC SIDE
+24, PS A IN
PIN 1, +24 VDC
PIN 2, GROUND
FIGURE 2.0 1584-29 MECHANICAL ASSEMBLY
1584-29 Manual, Rev C Page 6 3/7/19

2.2 Rear Panel Input/Output Connectors -
The input and output connectors on the rear panel are shown in Figure 2.1.
CAUTION! IF FUSES ARE INSTALLED IN THE Fuse 3 OR Fuse 4 HOLDERS, +22 VDC WILL APPEAR
ON THE CORRESPONDING SPLITTER INPUT CONNECTOR CENTER PINS.
GND
JIJ3J4J19 J5J6J7J9J10J11J12J14J15
OUTOUTOUTOUTOUTOUTOUTOUTOUTIN OUTOUTOUT
FUSE F4 FUSE F3
SPLITTER 2 OUTPUTS
Terminate when not used
1 INPUTAC 1 INPUT
100-240 ±10%
VAC 47-60HZ
Uses 2 amp Fast
Blo, 5mm Fuse
AC 2 INPUT
100-240 ±10%
VAC 47-60HZ
Uses 2 amp Fast
Blo, 5mm Fuse
AC1
GND
AC2
SPLITTER2 INPUT
CAUTION!
+22 VDC ON
CENTER PIN
CHASSIS
GROUND
SPLITTER1 INPUT
CAUTION!
+22 VDC ON
CENTER PIN
SPLITTER 1 OUTPUTS
Terminate when not used
FUSE FOR LNB2
1 amp Fast Blo, 1/4” Fuse FUSE FOR LNB1 1 amp Fast Blo, 1/4” Fuse
IN
J17 OUT J16 OUT
J15 OUT J14 OUT J13 OUT
J12 OUT J11 OUT J10 OUT J9 IN
J19 OUT J8 OUT J7 OUT J6 OUT
J5 OUT J4 OUT
J3 OUT J1
OUT
J2
FIGURE 2.1 1584-29 REAR PANEL
2.3 Front Panel Monitors and Indicators -
Figure 2.2 shows the front panel monitors and indicators.
RF2 - MONITOR
Monitors Splitter
2 output
POWER LED A
Lights green when DC voltage
is present from AC A power
supply.
LNB2 VOLTAGE LED
Lights Green when LNB voltage
is present on the Splitter input
A
AC POWER
B
LNBVOLTAGE
ONGND +DC
MODEL 1584
POWER DIVIDER CROSS TECHNOLOGIES INC.
MONITOR 1
RF
LNB VOLTAGE
ONGND +DC
MONITOR 2
RF
POWER LED B
Lights green when DC voltage
is present from AC B power
supply.
GROUND
TEST POINT LNB 2 VDC
TEST POINT
LNB1 VOLTAGE LED
Lights Green when LNB voltage
is
p
resent on the S
p
litter in
p
ut
GROUND
TEST POINT LNB 1 VDC TEST POINT
RF1 - MONITOR
Monitors S
p
litter 1 out
p
ut
FIGURE 2.2 1584-29 FRONT PANEL
1584-29 Manual, Rev C Page 7 3/7/19

2.4 Operation -
1.) Connect RF cables to the 1584-29 (See Section 2.2).
2.) IF DC VOLTAGE IS REQUIRED ON THE SPLITTER RF INPUT CENTER CONDUCTOR,
install 1/4”, 1 amp fast blo fuses in Fuse 3 and/or Fuse 4 holders.
CAUTION! IF FUSES ARE INSTALLED IN THE Fuse 3 OR Fuse 4 HOLDERS, +22 VDC WILL APPEAR
ON THE CORRESPONDING SPLITTER INPUT CONNECTOR CENTER PINS.
3.) Connect 100-240 ±10% VAC, 47 - 63 Hz to AC A and AC B on the back panel and observe
A and B LEDs are lit on the front panel.
4.) Monitor RF signals on the front panel monitors and DC voltage to the external amplifiers
(Front panel Green ON LEDs should be lit if LNB fuses are installed in the rear panel fuse holders)
to insure proper signals and voltages.
NOTE: FOR OPTIMUM PERFORMANCE, THE MONITOR PORT AND SPLITTER PORTS SHOULD BE
TERMINATED WITH 75 OHM TYPE F TERMINATIONS WHEN NOT USED.
5.) AC Fuse - The fuse is a 5mm, 2 amp fast blo and is inserted in the far slot in the drawer below the AC
input as shown in Figure 2.6. There is a spare fuse in the near slot. If a fuse continues to open, the power supply is
most likely defective. Note that each power supply module within the chassis also has a fuse but failure of this fuse
indicates the power supply may be defective.
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
FUSE DRAWER
SPARE FUSE
~
INPUT
100-240± 10%VAC
47-63 Hz
2A MAX
FUSE
TYPE T 2A GDC
250 VOLT
FOR 100 - 240 V~
~
FIGURE 2.6 FUSE LOCATION AND SPARE FUSE
1584-29 Manual, Rev C Page 8 3/7/19

CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
1584-29 Manual, Rev C Page 9 3/7/19