Cross Technologies 2116-116 User manual

Instruction Manual Model 2116-116
Block Downconverter
June 2010 Rev 0
MODEL 2116
CROSS TECHNOLOGIES INC.
POWER
EXT
10MHZ ALARM
DOWNCONVERTER
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]

INSTRUCTION MANUAL
MODEL 2116-116 Block Downconverter
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Rear Inputs and Outputs 6
2.3 Front Panel Indicators 6
2.4 Operation 7
3.0 Environmental Use Information 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and
workmanship for a period of one year after shipment to customer. Cross Technologies,
Inc.’s obligation under this warranty is limited to repairing or, at Cross Technologies, Inc.’s
option, replacing parts, subassemblies, or entire assemblies. Cross Technologies, Inc. shall
not be liable for any special, indirect, or consequential damages. This warranty does not
cover parts or equipment which have been subject to misuse, negligence, or accident by the
customer during use. All shipping costs for warranty repairs will be prepaid by the
customer. There are not other warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2116-116 Manual Page 2 06/231/10

MODEL 2116-116 Block Downconverter
1.0 General
1.1 Equipment Description
The 2116-116 Block Downconverter converts 11.7 - 12.2 GHz to 0.95 - 1.45 GHz with a local oscillator at
10.75 GHz. Front panel LEDs provide indication of DC Power, External 10 MHz, and PLL Alarm. The gain is
+35 dB. Connectors are SMA female for the RF and BNC female for the L-Band and external reference input
and reference output. A three-way switch controls which 10 MHz reference is being used. In the INT position,
the internal reference is used, in the EXT position, the external reference is used, and in the AUTO position, the
internal reference is used unless a 3 dBm ± 3 dB, 10MHz reference signal is connected to the external reference
input. The 2116 is powered by a 100-240 ±10% VAC power supply, and mounted in a 1 3/4” X 19” X 14” rack
mount chassis.
MODEL 2116
CROSS TECHNOLOGIES INC.
POWER
EXT
10MHZ ALARM
DOWNCONVERTER
FRONT PANEL
AC
GND
J8
J2
EXT 10MHZ RF INPUT
INPUT 10MHZ REF OUTPUT
INT EXT
AUTO
S1 J1
L-BAND
OUTPUT
J101
J11
ALARM
15 234 6
78
9
REAR PANEL
FIGURE 1.1 Model 2116-116 Front and Rear Panels
0.95
to
1.45
GHz
OUT
11.7
to
12.2
GHz
IN
11.7 to 12.2 GHz
BP
10.75
GHz
EXT
10MHz
INT
10MHz
2 GHz
LP
10
MHz
MON
AUTO
2116-116 Block Diagram
FIGURE 1.2 Model 2116-116 Downconverter Block Diagram
2116-116 Manual Page 3 06/231/10

1.2 Technical Characteristics
TABLE 1.0 2116-116 Downconverter Specifications*
Input Characteristics
Impedance/Return Loss 50/14 dB (see TABLE 2.2 for connector options)
Frequency 11.7 to 12.2 GHz
Noise Figure, max. 20 dB, max gain
Input Level -55 to -35 dBm
Input 1dB Compression -25 dBm
Output Characteristics
Impedance/Return Loss 50/14 dB (see TABLE 2.2 for connector options)
Frequency 0.95 to 1.45 GHz
Output Level Range -20 to 0 dBm
Output 1dB Compression +10 dBm
Channel Characteristics
Gain +35 dB ± 2 dB
Image Rejection >60 dB, min.
Spurious, In Band SIGNAL RELATED <-60 dBC in band, 0 dBm out
SIGNAL INDEPENDENT, <-60 dBm
Spurious, Out of Band <-50 dBm
Intermodulation <-55 dBC for two carriers each at -10 dBm out
Frequency Response ±1.5 dB, 0.95 to 1.45 GHz out; ± 0.5 dB, 40 MHz BW
Frequency Sense Non-inverting
LO Characteristics
LO Frequency 10.75 GHz
Frequency Accuracy ± 0.01 ppm max over temp internal reference; ext. ref. input
-110-100-85-80-70
1MHz100kHz10kHz1kHz100 Hz
dBC/Hz
Phase Noise
@
Fre
q
10 MHz In/Out Level +3 dBm ± 3 dB, 75 ohms, External In or Monitor Out
Controls, Indicators
Ext 10 MHz Yellow LED, Indicates Ext 10 MHz reference selected
PLL Alarm Red LED, External contact closure
Power Green LED
Other
RF Connector SMA (female), 50
L-Band Connector BNC (female), 50
10 MHz connectors BNC (female), 75connector;Works for 50/75
Alarm Connector DB9 - NO or NC contact closure on Alarm
Size 19” standard chassis, 1.75” high X 14.0” deep
Power 100-240 ±10% VAC, 47 - 63 Hz, 25 watts max.
Options
Connector options See TABLE 2.2
*+10˚C to +40˚C; Specifications subject to change without notice.
2116-116 Manual Page 4 06/231/10

2.0 Installation
2.1 Mechanical
The 2116-116 consists of a PCB and an RF assembly housed in a 1 RU (1 3/4 inch high) by 12 inch deep
chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2116-116 can
be secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2116-116 is assembled.
1
PS IN
PIN 1, +12 VDC
PIN 2, +5 VDC
PIN 3, +5 VDC
PIN 4, GROUND
PIN 5, GROUND
PIN 6, -12 VDC
PIN 7, +24 VDC
PIN 8, +24 VDC
POWER
SUPPLY
J10
J101 - Panel Mount
SMA Connector
PLL
VCO
J5
MIXER
AMP
BP FILTER
ISO
FIGURE 2.0 2116-116 Mechanical Assembly
2116-116 Manual Page 5 06/231/10

2.2 Rear Panel Input/Output Signals
Figure 2.1 shows the input and output connectors on the rear panel.
15 234
6
78
9
AC
GND
J8
J2
EXT 10MHZ RF INPUT
INPUT 10MHZ REF
OUTPUT
INT EXT
AUTO
S1 J1
L-BAND
OUTPUT
J101
J11
ALARM
AC INPUT
100-240 ±10%VAC, 47-63 HZ
Uses 2 amp Slow Blo,
5mm fuse
S1 - 10MHZ SWITCH
3-position switch. INT selects internal 10MHz ref.
AUTO selects internal 10MHz ref, unless a 3dBm
±3dB 10MHz signal is inserted on J2.
EXT selects external 10MHz ref from J2.
J101 - RF INPUT
SMA (female) 50 
11.7 to 12.2 GHz
-35 dBm max input signal
See Table 2.2 for other
connector options.
J8 - 10MHZ REF OUTPUT
BNC (female) 75 . Outputs currently
selected 10MHz ref signal (3 dBm ±3 dB).
J1 - L-BAND OUTPUT
BNC (female) 50 . 0.95 to 2.00 GHz,
0 dBm max input signal. See Table 2.2
for other connector options.
J2 - EXT 10MHZ INPUT
BNC (female) 75 . Insert external
10MHz reference here (3 dBm ± 3 dB).
J11 - ALARM
DB9 (female) connector.
See Table 2.1.
FIGURE 2.1 2116-116 Rear Panel I/Os
TABLE 2.1 JJ11
TABLE 2.1 J11 Pinouts (DB9)
Pin Function
1NotUsed
2NotUsed
3NotUsed
4NotUsed
5GND
6 Alarm Relay: Common
7 Alarm Relay: Normally Open
8NotUsed
9 Alarm Relay: Normally Closed
TABLE 2.2
Connector Optio
n
ns
Options
Option RF L-Band
STD SMA, 50BNC, 50
M
Type N, 50BNC, 50
N
Type N, 50BNC, 75
NF
Type N, 50Type F, 75
NN
Type N, 50Type N, 50
S7
SMA, 50BNC, 75
SF
SMA, 50Type F, 75
SN
SMA, 50Type N, 50
SS
SMA, 50SMA, 50
2.3 Front Panel Indicators
Figure 2.2 shows the front panel indicators.
DS2 - ALARM LED
Lights RED when PLL
comes out of lock.
DS1 - POWER LED A
Lights GREEN when DC voltage is
present from AC power supply.
DS3 - EXT 10MHZ LED
Lights YELLOW when external
10MHz reference is active.
POWER
EXT
10MHZ ALARM
FIGURE 2.2 2116-116 Front Panel Controls and Indicators
2116-116 Manual Page 6 06/231/10

2.4 Installation / Operation
2.4.1 Installing and Operating the 2116-116 Downconverter
1. Connect a -55 dBm to -35 dBm signal RF INPUT, J101 (Figure 2.1).
2. Connect the L-BAND OUTPUT, J1, to the external equipment.
3. Connect 100-240 ±10% VAC, 47 - 63 Hz to AC connector on the back panel.
4. Be sure DS1 (green, DC Power) is on and DS2 (red, Alarm) is off (Figure 2.2).
5. Select either INT (for internal 10MHz ref), AUTO (for internal 10MHz ref UNLESS an external
10MHz, 3 dBm signal is connected to J2), or EXT (for external 10MHz, 3 dBm ref that is inserted
at J2) on rear panel switch S1 (Figure 2.1).
6. If EXT is selected or AUTO is selected and there is a 10MHz, 3 dBm signal at J2, check that DS3
(yellow, Ext 10MHZ) is on (Figure 2.2).
7. Check that a 10MHz, 3 dBm ±3 dB signal is present at the 10MHZ REF OUTPUT (J8) (Figure 2.1).
8. AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot in
the drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot. If a fuse
continues to open, the power supply is most likely defective.
FUSE DRAWER
SPARE FUSE DRAWER
AC Fuse - 2 amp slow blow (Type T 2A GDC),
5 mm X 20 mm
~
INPUT
100-240± 10%VAC
47-63 Hz
2A MAX
FUSE
TYPE T 2A GDC
250 VOLT
FOR 100 - 240 V~
~
FIGURE 2.3 Fuse Location and Spare Fuse
2116-116 Manual Page 7 06/231/10

3.0 Environmental Use Information
A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical Loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C.Elevated Operating Ambient Temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced Air Flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between unit
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained.
Particular attention should be given to supply connections other than direct connection to the
Branch (use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
2116-116 Manual Page 8 06/231/10

CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2010 Printed in USA
2116-116 Manual Page 9 06/231/10