Cross Technologies 2099-10 User manual

Instruction Manual Model 2099-10
10MHz Reference
April 2019, Rev. E
POWER OVEN
MODEL 2099
FREQUENCY SOURCE CROSS TECHNOLOGIES INC.
Data, drawings, and other material contained herein are proprietary to Cross Technologies, Inc.,
but may be reproduced or duplicated without the prior permission of Cross Technologies, Inc.
for purposes of operating the equipment.
When ordering parts from Cross Technologies, Inc., be sure to include the equipment
model number, equipment serial number, and a description of the part.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]

INSTRUCTION MANUAL
MODEL 2099-10, 10MHz Reference
TABLE OF CONTENTS PAGE
Warranty 2
1.0 General 3
1.1 Equipment Description 3
1.2 Technical Characteristics 4
2.0 Installation 5
2.1 Mechanical 5
2.2 Rear Panel Outputs 6
2.3 Front Panel Indicators 6
2.4 Operation 7
3.0 Environmental Use Information 8
WARRANTY - The following warranty applies to all Cross Technologies, Inc. products.
All Cross Technologies, Inc. products are warranted against defective materials and workmanship for a period
of one year after shipment to customer. Cross Technologies, Inc.’s obligation under this warranty is limited
to repairing or, at Cross Technologies, Inc.’s option, replacing parts, subassemblies, or entire assemblies.
Cross Technologies, Inc. shall not be liable for any special, indirect, or consequential damages. This warranty
does not cover parts or equipment which have been subject to misuse, negligence, or accident by the customer
during use. All shipping costs for warranty repairs will be prepaid by the customer. There are not other
warranties, express or implied, except as stated herein.
CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
2099-10 Manual, Rev. E Page 2 04/02/19

MODEL 2099-10, 10MHz Reference
1.0 General
1.1 Equipment Description - The 2099-10, 10MHz Reference provides two 10 MHz outputs from a ±0.01ppm
high stability oven controlled crystal oscillator. Front panel LEDs provide indication of DC power and oven
warm-up. The level is +7 dBm and the 2099-10 works into either a 75 or 50 ohm load (Option D). Connectors
are BNC female. A relay contact closure or open indicates when the oscillator oven is stabilized. Powered by a
100-240 (±10%) VAC power supply; 1 3/4” X 19” X 14” rack mount chassis.
POWER OVEN
MODEL 2099
FREQUENCY SOURCE CROSS TECHNOLOGIES INC.
FRONT PANEL
AC
GND
J19
MONITOR
AND
CONTROL REFERENCE OUTPUTS
J1 J2
15
23
46
78
9
REAR PANEL
FIGURE 1.1 Model 2099-10 Front and Rear Panels
10.0000 MHz
OVEN XO
10MHZ
OUTPUT 1
SPLITTER
10MHZ
OUTPUT 2
OVEN WARM-UP
TO LED & RELAY
FIGURE 1.2 Model 2099-10, 10MHz Reference Block Diagram
2099-10 Manual, Rev. E Page 3 04/02/19

1.2 Technical Characteristics
TABLE 1.0 2099-10, 10MHz Reference Specifications*
Output Characteristics
Number of Outputs 2
Impedance 75Ω
Return Loss > 18 dB
Frequency 10.0000 MHz
Output Level +7 dBm ± 3 dBm
Harmonics < -30 dBC, < -40 dBC typ.
Spurious < -75 dBC
Oscillator Stability
Oven Temperature ±0.01 ppm max, 0˚C to +50˚C
Aging, per day ±0.001 ppm
Aging, per year ±0.1 ppm
Warm-Up, in 4 minutes ±0.1 ppm
Warm-Up, in 1 hour ±0.01 ppm
Mechanical adjustment ±0.1 ppm
Oscillator Phase Noise
-160-155-140-110
10kHz1kHz100Hz10Hz
dBC/Hz
Phase Noise @ Freq
Controls, Indicators
Power Green LED
Oven Warm-Up Yellow LED, External contact closure (No contact closure with -Option W45)
Other
10MHz Connector BNC (female) 50Ωor 75Ωper customer specification
Alarm Connector DB9, female - NO or NC contact closure on Alarm
Size 19 inch, 1RU standard chassis 1.75”high X 14.0” deep
Power 100-240 (± 10%) VAC, 47-63 Hz, 20 watts max
Options
- D 50ΩOutput
-W45 Provides Level Alarm Indicator and Contact Closure
*+10˚C to +40˚C; Specifications subject to change without notice.
2099-10 Manual, Rev. E Page 4 04/02/19

2.0 Installation
2.1 Mechanical - The 2099-10 consists of one RF PCB housed in a 1 RU (1 3/4 inch high) by 14 inch deep
chassis. A switching, ± 12, +24, +5 VDC power supply provides power for the assemblies. The 2099-10 can be
secured to a rack using the 4 holes on the front panel. Figure 2.0 shows how the 2099-10 is assembled.
POWER
SUPPLY
FIGURE 2.0 2099-10 Mechanical Assembly
2099-10 Manual, Rev. E Page 5 04/02/19

2.2 Rear Panel Output Signals - Figure 2.1 shows the input and output connectors on the rear panel.
AC
GND
J19
MONITOR
AND
CONTROL REFERENCE OUTPUTS
J1 J2
J1, J2 - REFERENCE OUTPUTS
BNC (female)
10.0000 MHz, +7 dBm out
p
ut si
g
nal.
AC INPUT
100-240 ±10% VAC, 47-60 HZ
Uses 2 amp Slow Blo, 5mm fuse
J19 - MONITOR AND CONTROLS
DB9
(
female
)
connector. See Table 2.1.
15
23
46
78
9
FIGURE 2.1 2099-10 Rear Panel Outputs
1
6
2345
7
8 9
TABLE 2.1 J119
TABLE 2.1 J19 Pinouts (DB9)
Pin Function
1 Not Used
2 Not Used
3 Not Used
4 Not Used
5GND
6 Alarm Relay: Common
7 Alarm Relay: Open=ALARM
8 Not Used
9 Alarm Relay: Closed=ALARM
2.3 Front Panel Indicators -The following are the front panel indicators.
DS4 - OVEN LED
Lights YELLOW while oven warms up.
DS6 - POWER LED
Lights GREEN when DC voltage is
present from AC power supply.
MODEL 2099
CROSS TECHNOLOGIES INC.
POWER
FREQUENCY SOURCE
OVEN
FIGURE 2.2 2099-10 Front Panel Controls and Indicators
2099-10 Manual, Rev. E Page 6 04/02/19

2.4 Installation / Operation
2.4.1 Installing and Operating the 2099-10, 10MHz Reference
1.) Connect REFERENCE OUTPUTS, J1 and/or J2, to the external equipment (Figure 2.1).
2.) Connect 100- 240 (±10%) VAC, 47 - 63 Hz to AC connector on the back panel.
3.) Be sure DS6 (green, POWER) is on (Figure 2.2).
4.) Wait for DS4 (yellow, OVEN WARM-UP) to go off and/or contact closure at DB9 ALARM
connector, J19, to occur to insure that the oscillator oven is stabilized.
5.) AC Fuse - The fuse is a 5 mm X 20 mm, 2 amp slow blow (Type T) and is inserted in the far slot
in the drawer below the AC input as shown in Figure 2.3. There is a spare fuse in the near slot.
If a fuse continues to open, the power supply is most likely defective.
AC Fuse - 2 amp slow blow (Type T),
5 mm X 20 mm
FUSE DRAWER
SPARE FUSE
~
INPUT
100-240± 10%VAC
47-63 Hz
2A MA
X
FUSE
TYPE T 2A GDC
250 VOL
T
FOR 100 - 240 V~
~
FIGURE 2.3 Fuse Location and Spare Fuse
2099-10 Manual, Rev. E Page 7 04/02/19

3.0 Environmental Use Information
A.Rack-Mounting - To mount this equipment in a rack, please refer to the installation instructions
located in the user manual furnished by the manufacturer of your equipment rack.
B. Mechanical loading - Mounting of equipment in a rack should be such that a hazardous condition
does not exist due to uneven weight distribution.
C.Elevated operating ambient temperature - If installed in a closed or multi-unit rack assembly,
the operating ambient temperature of the rack may be greater than room ambient temperature.
Therefore, consideration should be given to Tmra.
D. Reduced air flow - Installation of the equipment in a rack should be such that the amount of air flow
required for safe operation of the equipment is not compromised. Additional space between units
may be required.
E. Circuit Overloading - Consideration should be given to the connection of the equipment to the supply
circuit and the effect that overloading of circuits could have on over current protection and supply wiring.
Appropriate consideration of equipment name plate rating should be used, when addressing this concern.
F. Reliable Earthing - Reliable earthing of rack-mounted equipment should be maintained. Particular
attention should be given to supply connections other than direct connection to the Branch
(use of power strips).
G. Top Cover - There are no serviceable parts inside the product so, the Top Cover should not be removed.
If the Top Cover is removed the ground strap and associated screw MUST BE REINSTALLED
prior to Top Cover screw replacement. FAILURE TO DO this may cause INGRESS and/or EGRESS
emission problems.
2099-10 Manual, Rev. E Page 8 04/02/19

CROSS TECHNOLOGIES, INC.
6170 Shiloh Road
Alpharetta, Georgia 30005
[phone]
FAX [phone]
Toll Free 888-900-5588
WEB www.crosstechnologies.com
E-MAIL [email protected]
Printed in USA
2099-10 Manual, Rev. E Page 9 04/02/19