Crux DKGM-49 User manual

- Retains factory features in select GM LAN 29 Bit vehicles while functioning with an aftermarket radio.
- Pre-programmed to retain factory Steering Wheel Controls.
- iPhone Voice Recognition (VR) feature from SWC on Kenwood, Pioneer, Alpine and JVC radios.
- Supports Pick Up/End Call, Pick Up and Toggle between 1st and 2nd Incoming call, AVRCP Track, Seek.
- Supports Bose, non-Bose and Y-91 audio systems.
- Provides Factory Rear Seat Entertainment Activation. Requires Cable #CRUX2333A
(sold separately).
- Retains factory front and back park assist system.
- Retains chime functions.
- EIA color coded wiring for easy installation.
1. *NOT compatible with 2012-Up SUVs/Trucks that are equipped with factory-installed Navigation
radios.
2. **NOT compatible with Express and Savana vans that are powered by a diesel engine.
3. Supports Rear Entertainment System with special order harness #CJA2333A (sold separately).
4. DOES NOT support ONSTAR.
GM-49 Module
GM-49 Harness
SWC Cables
Antenna Adaptor
CRUX2543
Dash Kit
Rev.032917
1 / 6
GMC
2007-2015 Acadia
2008-2013 Savana**
2007-2013 Sierra 1500-3500
Pickup*
2007-2014 Yukon*
HUMMER
2008-2009 H2
PONTIAC
2007-2009 Torrent
SATURN
2007-2010 Outlook
2008-2009 Vue
SUZUKI
2007-2008 XL7
BUICK
2008-2015 Enclave
2006-2011 Lucerne
CADILLAC
2006-2011 DTS
2007-2014 Escalade
2007-2009 SRX
CHEVROLET
2007-2013 Avalanche*
2007-2008 Equinox
2008-2013 Express Van**
2006-2013 Impala / Impala SS
2006-2007 Monte Carlo
2007-2013 Silverado 1500-3500
Pickup*
2007-2014 Suburban*
2007-2014 Tahoe*
2009-2015 Traverse

SETTING THE AFTERMARKET RADIO BRAND
With the key in the off position, set the DIP switches to the corresponding radio listed below.
3.5MM SWC CABLE
The DKGM-49 Module allows for both types of connections:
OPTION A is used for ALPINE, CLARION, JVC, and KENWOOD units (Blue/Yellow wire is attached)
OPTION B is used for BOSS, DUAL, FAHRENHEIT, JENSEN, POWER ACOUSTIK, PIONEER, SONY and
SOUND STREAM units.
NOTE: Cap or insulate the 3.5mm plug or Blue/Yellow wire if not being used.
2 / 6
Rev.032917

If the vehicle is equipped with a Bose system, the DKGM-49 module has a built-in Bose adaptor that allows the
proper audio input gain from the aftermarket radio to the Bose amplifier. To use this feature, plug in the male 8-pin
connector on the harness to the GRAY female 8-pin connector on the DKGM-49 module. The module is also labeled
“Bose” and “Non Bose” to avoid confusion. (see picture below)
If the vehicle is NOT equipped with a Bose system, plug in the male 8-pin connector to the BLACK female 8-pin on
the GM-49 module.
The DKGM-49 module has a potentiometer to adjust the chime volume. It is set at half way by default. To adjust
the volume, simply use a suitable screw driver and turn the potentiometer clockwise to increase the volume and
counter-clockwise to decrease the volume.
You can retain use of the factory backup camera by using the CRUX2543 harness provided in the kit. See below for
connection instructions. (Note: Loose wires may not be needed in the installation.)
3 / 6
Rev.032917
BOSE
Connection
Non-BOSE
Connection
Chime
Volume
Adjustment

A double DIN radio replacement dash kit is included in the kit to make the installation quick and easy. You have the
option of installing a Double DIN or two Single DIN radios. The DKGM-49 kit includes:
(1) Main trim ring
(1) Left ISO mounting bracket
(1) Right ISO mounting bracket
Installation:
NOTE: Suzuki XL7 trim top corners of radio housing. See diagram A.
Diagram A
Before installation:
1. Locate the main trim ring.
2. Locate the left and right mounting brackets.
3. Slide the appropriate mounting bracket into the trim ring, aligning the holes in the trim ring to the clips on the bracket.
(See Diagram B)
4.For two Single DIN radio installation, slide the stacked ISO DIN unit into the trim ring bracket assembly and secure the unit to
the kit using the screws supplied with the radio. (See Diagram C)
Diagram B
Diagram C
4 / 6
Rev.032917

STEERING WHEEL CONTROL BUTTON FUNCTIONS
SWC Button
SHORT PRESS
LONG PRESS
PIONEER
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
►I
Voice
Step Increment
Step Decrement
Preset Up
Preset Down
Source
Tune
Pick Up Call
Continuous VOL +
Continuous VOL -
Seek Up
End Call
Power On/Off
Mute On/Off
Activate VR/Deactivate VR
SWC Button
SHORT PRESS
LONG PRESS
ALPINE
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
►I
Voice
*NOTE:
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Preset
Pick Up Call
To Deactivate VR = Say “CANCEL”
Continuous VOL +
Continuous VOL –
None
End Call
None
ATT On/Off
Activate VR*/Deactivate VR*
BT Mode Active:
Voice = Toggle between 1st and 2nd Call
SWC Button
SHORT PRESS
LONG PRESS
CLARION
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
►I
Voice
Step Increment
Step Decrement
Preset Up
Preset
Source
None
Pick Up Call
Continuous VOL +
Continuous VOL –
Seek Up
End Call
Power On/Off
Mute On/Off
Mute On/Off
SWC Button
SHORT PRESS
LONG PRESS
JVC
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
►I
Voice
NOTE:
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Preset
Pick Up Call
To Deactivate VR = Say “CANCEL”
Continuous VOL +
Continuous VOL –
M-Seek Up
End Call
None
Mute On/Off
Activate VR
5 / 6
Rev.032917

SWC Button
SHORT PRESS
LONG PRESS
KENWOOD
VOL +
VOL -
Arrow Up ▲
Arrow Down ▼
SRCE
►I
Voice
NOTE:
Step Increment
Step Decrement
Seek Up
Seek Down
Source
Preset
Pick Up Call / Call History On/Off
To Deactivate VR = Say “CANCEL”
Continuous VOL +
Continuous VOL -
None
End Call / Deactivate VR
None
ATT On/Off
Activate VR
BOSS Radio SWC Programming
SWC Radio Wiring connection
SWC Key1 (Brown-wire) connect to Female 3.5 mm Jack - Brown wire
SWC Key2 (White-wire) connect to Female 3.5 mm Jack - Brown/White wire
SWC GND (Black-Wire) connect to Radio Negative wire (Black)
Programming the Radio
Press: [SETTING] > [STEER] > [RESET] > [High Z]
Press the Steering Wheel Control (SWC) buttons set the values as listed below:
Vol –[ 4.07]
Vol + [ 3.66]
Seek –[ 3.37]
Seek + [ 2.98]
Mode [1.39]
OFF Hook [ 0.00]
The Value in the bracket [X.XX] will vary and will be used as parameter for each assigned function.
Press: [Assign] > [4.07] > [Vol-], then the [4.07] will be replaced with [ Vol-]
With [Assign] highlighted:
Press: [3.66] > [Vol+], then the [3.66] will be replaced with [Vol+]
Press: [3.37] > [Seek-], then the [3.37] will be replaced with [Seek-]
Press: [2.98] > [Seek+], then the [2.98] will be replaced with [Seek+]
Press: [1.39] > [Mode], then the [1.39] will be replaced with [Mode]
Press: [0.00] > [Call], then the [0.00] will be replaced with [Call]
Press: [Enter] for Save the setting and Exit
rev.032717
7 / 7
6 / 6
Rev.032917