dams FZ1600OL User manual

FZ1600OL
Fuze Outer Leg
08.03.2018
1
Used to build
Fuze Back to Back Desk Fuze Boardroom Table
SCREEN
FIXING
POINTS
POINTS
FIXING
BEAM
POINTS
FIXING
BEAM
DESKTOP
FIXING
POINTS
DESKTOP
FIXING
POINTS

2
1,2,3...
TOOLS REQUIRED
FOR ASSEMBLY
DONT STRUGGLE
2 MAN LIFT
ALWAYS HANDLE
ITEMS WITH CARE
IF UNSURE CALL
FOR ASSISTANCE
KEEP FITTINGS AWAY
FROM CHILDREN

Please check that you have all the components
12 x DESK TOP
22 x OUTER LEG FRAMES ( FZ1600OL )
42 x BEAM PACK
1200mm = ED12BM
1400mm = ED14BM
1600mm = ED16BM
FITTINGS SUPPLIED WITH EACH LEG
4x
4x
Leg Spacer Block
Beam Infill Block
M6 x 60mm Connect Bolt
3
11 x TABLE TOP
or
800mm Deep Tops
1200mm = ED128T
1400mm = ED148T
1600mm = ED168T
1600mm Deep Tops
1200mm = EDBT1216T
1600mm = EDBT1616T
32 x OUTER LEG PANELS ( FZW-1 )
4x
4x
M8 x 50mm Bolt
8mm Washer
2x
M8 Adjustable Foot
8x
8x
M6 x 25mm Connect Bolt

1
Step 1
Insert the beam infill blocks
into both ends of the beam.
Step 2
Push the beams onto
the 1st leg frame lining
up the beam holes with
the M6 threaded holes
on the leg.
Ensure the screen
fixing points on the
outer leg and cut out
slots on the beams are
facing inwards.
2
3
Step 3
Once the holes are
aligned fix the beam in
place using the
M6 x 25mm Connect
Bolts.
8x
Back to Back Desk Assembly
M6 x 25mm Connect Bolt
4

5
Step 4
Push the beams onto
the remaining leg frame
lining up the beam holes
with the M6 threaded
holes on the leg.
Please Note
If you have purchased a
larger configuration of
desk than the one
shown please refer to
the FZ1600IL instruction
before proceeding with
step 4
4
5
Step 5
Once the holes are
aligned fix the beam in
place using the
M6 x 25mm Connect
Bolts.
8x
M6 x 25mm Connect Bolt
Please Note
If you have purchased a sliding top system please refer to the sliding top
bracket assembly instruction from this point onwards.

Step 6
Position the Spacer
Blocks over the holes
in the leg frames.
6
Leg Spacer Block
8x
6
Please Note
For ease of assembly Screen Brackets and
Horizontal Cable Trays should be fitted before
you proceed to Step 7.
Ensure that the
spacer blocks
are placed onto
the frame with
the recessed
nut holes
facing upwards.

7
7
Step 7
Place the desktop onto
the assembled
framework ensuring
that the edges of the
desktop finish parallel
with the end of the leg
frames.
The framework may be
slightly out of square,
if this happens loosen
the fixing bolts in the
beams and align
correctly before re
tightening the bolts.
or

8
8
8x
M6 x 60mm Connect Bolt
Step 8
Attach one side of the
desktops to the frame
using the M6 x 60mm
Connect Bolts.
Ensure that the bolt
passes through both
the leg frame and
Spacer Block.
9
8x
M6 x 60mm Connect Bolt
Step 9
Attach the remaining
side of the desktops to
the frame using the M6
x 60mm Connect Bolts.
Ensure that the bolt
passes through both
the leg frame and
Spacer Block.

FZ1600IL
Fuze Inner Leg
08.03.2018
1
Used to build
Fuze Back to Back Desk Fuze Boardroom Table
SCREEN
FIXING
POINTS
POINTS
FIXING
BEAM
POINTS
FIXING
BEAM
DESKTOP
FIXING
POINTS
DESKTOP
FIXING
POINTS

Please check that you have all the components
1DESK TOP
(Number of tops is dependant on configuration )
800mm Deep Tops
1200mm = ED128T
1400mm = ED148T
1600mm = ED168T
4BEAM PACK
( Number of beams is dependant on configuration )
1200mm = ED12BM
1400mm = ED14BM
1600mm = ED16BM
1TABLE TOP
(Number of tops is dependant on configuration )
1600mm Deep Tops
1200mm = EDBT1216T
1600mm = EDBT1616T
or
2
21 x INNER LEG FRAMES ( FZ1600IL )
FITTINGS SUPPLIED WITH EACH LEG
4x
4x
Leg Spacer Block
Beam Infill Block
M6 x 60mm Connect Bolt
31 x INNER LEG PANELS ( FZW-2 )
4x
4x
M8 x 50mm Bolt
M8 Knock In Insert
2x
M8 Adjustable Foot
8x
8x
M6 x 25mm Connect Bolt