danalock Danapad PADV3-BT Guide

poly-control aps
Gammel Stillingvej 427 C, DK – 8462 Harlev, [phone] mobile [phone], www.poly-control.com
Federal Communication Commission
Equipment Authorization Division, Application Processing Branch
7435 Oaklan Mills Roa
Columbia, MD 21048
Certification and Engineering Bureau
In ustry Cana a
Spectrum Engineering Branch
3701 Carling Avenue, Buil ing 94
Ottawa, Ontario K2H 8S2, Cana a
June 19
th
, 2018
Declaration for IC and FCC Label Exemption for Danapad PADV3-B
With reference to In ustry Cana a, RSP-100 issue 11 chapter 3 Certification of Ra io Apparatus an
KDB 784748 D01v08 GUIDELINES FOR LABELLING AND USER INFORMATION FOR DEVICES SUBJECT TO
PART 15 AND PART 18, Poly-Control aps hereby eclare an exemption regar ing the labelling of the IC
an FCC certification number on the Danapa PADV3-BT pro uct.
This exception applies to the Danalock Danapa electronic lock access panel with IC/FCC ID 12588A-
PADV3B an 2ADSH-PADV3B . The Danapa mo el number, IC an FCC certification numbers are
locate on the evice removable battery li , see Annex A. The Danapa mo el number, IC an FCC
certification numbers are a itionally liste in the user manual an /or on the pro uct packaging
material, see Annex A Box label an user gui e information.
The label placement exemption eclaration is base on the fact that the Danapa is an out oor wall
mounte wireless access panel to operate the in oor Danalock electronic oor lock or lock controller.
The label placement is a protective place with respect to the out oor environment an the battery li
is essential for the weather an IP protection of the unit an batteries ue to temperature, humi ity,
water, salt mist etc. that the user will not lose the li . The sunlight an weather con itions uring the
lifetime of the Danapa oes not allow for a feasible permanent label placement except for the battery
li .
For your information, our TCB is PHOENIX TESTLAB GmbH in Germany.
Sincerely,
Per K. Nielsen (on behalf of Poly-Control aps)
Certification consultant
[email protected]

poly-control aps
Gammel Stillingvej 427 C, DK – 8462 Harlev, [phone] mobile [phone], www.poly-control.com
Annex A
Pro uct mounting an labeling information.
Mounting:
Please follow the installation gui e carefully.
Installation gui es are available on the Danalock site an can be viewe by following this link:
https://guide.danalock.com/
•Attach mounting plate to wall with screws or a hesive so the screw holes are horizontal. The
Danapa shoul be mounte less than 10 meters away from the Danalock or Danapa to be in
range.
•Insert 4x AAA batteries into Danapa an close waterproof li . The Display shoul light up
green when powere on. To secure water resistance check that the rubber gasket is in place
before clicking on the battery li . The Danapa is IP54 protecte when close correctly to
withstan the out oor weather con itions.
•Mount Danapa on mounting plate by inserting it slightly offset to the left "rotate counter-
clockwise" an rotating it clockwise. The Danapa will make an au ible click when mounte
correctly.

Danapad
Label pictures
Danapad batch label placement
(inside battery compartment)
Danapad back side with label
Danapad model label placement
(outside battery compartment)
Danapad front side
poly-control aps
Gammel Stillingvej 427 C, DK – 8462 Harlev, [phone] mobile [phone], www.poly-control.com

Danapad
Label pictures
Danapad batch labelDanapad model label
Danapad product packaging label
204-820259
Name: Danapad
Model: PADV3-BT
FCC ID: 2ADSH-PADV3BT
IC: 12588A-PADV3BT
Barcode
204-820259
Name: Danapad
Model: PADV3-BT
FCC ID: 2ADSH-PADV3BT
IC: 12588A-PADV3BT
Notice: This product complies with Part 15 of the FCC rules and with Industry Canada license exempt
standard(s). Operation is subject to the following two conditions: (1) This device may not cause
harmful interference, and (2) This device must accept any interference received, including interference
that may cause undesired operation.
The Bluetooth® word mark and logos are registered trademarks owned by the Bluetooth SIG, Inc. and
any use of such marks by Poly-Control ApS is under license. Other trademarks and trade names are
those of their respective owners
Danalock ApS, Gammel Stillingvej 427C, 8462 Harlev, DK, [phone], [e-mail]
Country of origin: CN
poly-control aps
Gammel Stillingvej 427 C, DK – 8462 Harlev, [phone] mobile [phone], www.poly-control.com

poly-control aps
Gammel Stillingvej 427 C, DK – 8462 Harlev, [phone] mobile [phone], www.poly-control.com