danalock V3 US Product information sheet

Danalock V3 US Easy install page 1/3
1. Download the Danalock app
Go to Google Play or App Store
and download the Danalock App.
When the app is installed you
create a user profile by pressing the
blue ring. You will use this profile
each time you sign into the app.
You will need to finish setting the
Danalock up in the app after
mounting it on the door.
2. Get your tools together
To install the Danalock,
you’ll need a Phillips
screwdriver and tape,
preferably masking tape.
Should you need to
remove or readjust the
lock, a pen tip or paper
clip will be needed.
3. Check door alignment
Ensure that your door is
properly aligned before
beginning installation.
You should be able to lock
your door without pushing,
pulling, or lifting the door.
Thumb-turn
must move and
lock smoothly.
4. Secure outside keyhole
Before removing your
existing lock, use tape to
secure the outside
keyhole. This will keep it
in place as you remove
the screws on the inside.
5. Remove inside thumb-turn
Remove the inside thumb-turn,
leaving just the deadbolt and
tailpiece remaining.
Set aside the screws. You’ll
reinstall them in step 7.
6. Select a backplate
Find the backplate that
matches the brand of
your existing lock.
Deadbolt
Tailpiece Thumb-turn
Thumb-turn
screws
Tailpiece adapters Danalock V3
B
Defia nt
Schla ge, Weiser
Back plate
AOmnia
Weslock BSchlage Weiser CBaldwin
Emtek
Kwikset

Danalock V3 US Easy install page 2/3
8. Fasten backplate
Fasten the backplate where the thumb-turn
was using the two original screws, with the
arrow on the label pointing up.
7. Remove the paper from the stickers
On the backside of
the backplate you’ll
find three stickers.
Remove the paper
from the stickers.
The notches on the backplate must
be facing out with the tailpiece
centered exactly in the middle hole.
9. Select tailpiece adapter
Select the tailpiece adapter that matches
the shape of your existing lock’s tailpiece.
10. Insert adapter into Danalock
Insert the selected
tailpiece adapter into
your Danalock and press
until it clicks in place.
11. Fit and fasten Danalock
Fit the Danalock onto the backplate with the battery cover facing down, the tailpiece
sliding into the adapter and the backplate notches into the back of the lock.
B
Defiant
Schla
g
e, Weiser
Baldwin
Defiant
Emtek
Omnia
Weiser
Weslock
Baldwin
Kwikset
Schlage
Depends on the length
of your tailpiece.
Battery cover
facing down
Click!
Find the small marking
at the edge of the
backplate and align it
with the hole in the
cover ring surrounding
the Danalock
Now you are sure to hit
the notches on the
backplate with the
Danalock.
12. Align the platemarks
Turn the Danalock
clockwise until it clicks to
fasten it to the back plate.
NOTE: If you need to
unfasten and retry, see
“Uninstall instructions” at
the end of the manual.
13. Fasten the Danalock
Original screws
Tailpiece
Backplate
Click!
14. Activate batteries
Pull out the plastic tab
to activate the batteries.
A light will flash to
confirm the Danalock
is ready.
Note: If the batteries are
disconnected, you will have
to re-calibrate the Danalock.

Danalock V3 US Easy installDanalock V3 US Easy install page 3/3
15. Complete setup
in the Danalock app
Your Danalock is now
attached to the door.
Download and open
the Danalock app to
finish setting it up.
Leave the door open,
so the lock isn’t
influenced when
calibrated.
Open the Danalock app you
downloaded at the start. When you
have logged in you will see your
empty keychain. Press ”Add lock” at
the bottom of the screen.
A guide will now lead you through
the installation and configuration
of your Danalock.
16. Download the Danalock App
If at any time you need to dismount
the Danalock from your door, insert
a pen tip into the hole at the top
inner edge of the lock and press
while turning the lock counter-
clockwise until the lock releases.
This will not reset the lock or
disconnect it from your account,
but the lock may need to be
re-calibrated if fastened to
your door again.
17. Dismount instructions
Add lock
Settings Lock users Log Menu
You have no keys
Add your first lock
by pressing the
”Add lock” icon
below