danalock V3 US User manual

Danalock V3 US
www.danalock.com

Table of content
0. Parts involved 5
1. Download the Danalock app 6
2. Get your tools together 7
3. Check door alignment 8
4. Secure outside keyhole 9
5. Remove inside thumb-turn 10
6. Select a backplate 11
7. Remove the paper from the stickers 12
8. Fasten backplate 13
9. Select tailpiece adapter 14
10. Insert adapter into Danalock 15
11. Fit and fasten Danalock 16
12. Align the platemarks 17
13. Fasten the Danalock 18
14. Activate batteries 19
15. Before completing the setup 20
16. Open the Danalock app 21
17. Dismount instructions 22
18. LED-Signals 23
19. Conguring the Danalock V3 with click-commands 24

3
0. Parts involved

4
1. Download the Danalock app
Go to Google Play or App Store and download the Danalock app.
When the app is installed you create a user prole by pressing the
blue ring. You will use this prole each time you sign into the app.
You will need to nish set-
ting the Danalock up in the
app after mounting it on
the door.
Add
lock
SettingsLock
users LogMenu

5
2. Get your tools together
To install the Danalock, you’ll need a Phillips screwdriver and tape,
preferably masking tape. Should you need to remove or readjust
the lock, a pen tip or paper clip will be needed.

6
3. Check door alignment
Ensure that your door is properly aligned before beginning instal-
lation.
You should be able to lock
your door without pushing,
pulling, or lifting the door.
Thumb-turn
must move and
lock smoothly.

7
4. Secure outside keyhole
Before removing your existing lock, use tape to secure the outside
keyhole. This will keep it in place as you remove the screws on the
inside.

8
5. Remove inside thumb-turn
Remove the inside thumb-turn, leaving just the deadbolt and tail-
piece remaining. Set aside the screws. You’ll reinstall them in step 8.

9
6. Select a backplate
Find the backplate that matches the brand of your existing lock.

10
7. Remove the paper from the stickers
On the backside of the backplate you’ll nd three stickers.
Remove the paper from the stickers.

11
8. Fasten backplate
Fasten the backplate where the thumb-turn was using the two
original screws, with the arrow on the label pointing up.
The notches on the backplate must be
facing out with the tailpiece centered
exactly in the middle hole.
Original screws

12
9. Select tailpiece adapter
Select the tailpiece adapter that matches the shape of your existing
lock’s tailpiece.
Baldwin
Emtek
Omnia
Weiser
Weslock
Baldwin
Kwikset
Schlage
Depends on the length
of your tailpiece.

13
10. Insert adapter into Danalock
Insert the selected tailpiece adapter into your Danalock and press
until it clicks in place.
Click!

14
11. Fit and fasten Danalock
Fit the Danalock onto the backplate with the battery cover fac-
ing down, the tailpiece sliding into the adapter and the backplate
notches into the back of the lock.
Battery cover
facing down
Tailpiece
Backplate

15
12. Align the platemarks
Find the small marking at the edge of the backplate and align it with
the hole in the cover ring surrounding the Danalock. Now you are
sure to hit the notches on the backplate with the Danalock.

16
13. Fasten the Danalock
Turn the Danalock clockwise until it clicks to fasten it to the backplate.
NOTE: If you need to unfasten and retry, see “Uninstall instructions”
on p. 22.
Click!

17
14. Activate batteries
Pull out the plastic tab to activate the batteries. A light will ash to
conrm the Danalock is ready.
Note: If the batteries are disconnected, you will have to re-calibrate
the Danalock.

18
15. Before completing the setup
Your Danalock is now attached to the door.
Leave the door open, so
the lock isn’t inuenced
when calibrated.

19
16. Open the Danalock app
Open the Danalock app you downloaded at the start. When you
have logged in you will see your empty keychain. Press ”Add lock” at
the bottom of the screen.
A guide will now lead you
through the installation
and conguration of your
Danalock.
Add
lock
SettingsLock
users LogMenu
You
have
no
keys
Add
your
first
lock
by
pressing
the
”Add
lock”
icon
below

20
17. Dismount instructions
If at any time you need to dismount the Danalock from your door, in-
sert a pen tip into the hole at the top inner edge of the lock and press
while turning the lock counter- clockwise until the lock releases.
This will not reset the lock
or disconnect it from your
account, but the lock may
need to be re-calibrated
if fastened to your door
again.