danalock V3 US Installation instructions manual

Danalock V3 US
Mounting guide
www.danalock.com

Page 2
Table of contents
Parts involved page 4
1. Download the Danalock app page 5
2. Get your tools together page 6
3. Check door alignment page 7
4. Secure outside keyhole page 8
5. Remove inside thumb-turn page 9
6. Select a backplate page 10
7. Remove the paper from the stickers page 11
8. Fasten backplate page 12
9. Select tailpiece adapter page 13
10. Insert adapter into Danalock page 14

Page 3
Table of contents
11. Fit and fasten Danalock page 15
12. Align the platemarks page 16
13. Fasten the Danalock page 17
14. Activate batteries page 18
15. Before completing the setup page 19
16. Open the Danalock app page 20
17. Dismount instructions page 21
18. LED-Signals page 22
21. How to operate the Danalock V3
with click-commands page 23

Page 4
Parts involved:

Page 5
1. Download the Danalock app
Go to Google Play or App Store and download the Danalock
app. When the app is installed you create a user prole by
pressing the blue ring. You will use this prole each time you
sign into the app.
You will need to
nish setting the
Danalock up in the
app after mounting
it on the door.

Page 6
2. Get your tools together
To install the Danalock, you’ll need a Phillips screwdriver
and tape, preferably masking tape. Should you need to
remove or readjust the lock, a pen tip or paper clip will
be needed.

Page 7
3. Check door alignment
Ensure that your door is properly aligned before beginning
installation.
You should be able
to lock your door
without pushing,
pulling, or lifting
the door.
Thumb-turn
must move and
lock smoothly.

Page 8
4. Secure outside keyhole
Before removing your existing lock, use tape to secure
the outside keyhole. This will keep it in place as you
remove the screws on the inside.

Page 9
5. Remove inside thumb-turn
Remove the inside thumb-turn, leaving just the deadbolt
and tailpiece remaining. Set aside the screws.
You’ll reinstall them in step 7.

Page 10
6. Select a backplate
Find the backplate that matches the brand
of your existing lock.

Page 11
7. Remove the paper from the stickers
On the backside of the backplate you’ll nd three stickers.
Remove the paper from the stickers.

Page 12
8. Fasten backplate
Fasten the backplate where the thumb-turn was using the
two original screws, with the arrow on the label pointing up.
The notches on the backplate must be
facing out with the tailpiece centered
exactly in the middle hole.
Original screws

Page 13
9. Select tailpiece adapter
Select the tailpiece adapter that matches the shape of your
existing lock’s tailpiece.
Baldwin
Emtek
Omnia
Weiser
Weslock
Baldwin
Kwikset
Schlage
Depends on the length
of your tailpiece.

Page 14
10. Insert adapter into Danalock
Insert the selected tailpiece adapter into your Danalock and
press until it clicks in place.
Click!

Page 15
11. Fit and fasten Danalock
Fit the Danalock onto the backplate with the battery
cover facing down, the tailpiece sliding into the adapter
and the backplate notches into the back of the lock.
Battery cover
facing down
Tailpiece
Backplate

Page 16
12. Align the platemarks
Find the small marking at the edge of the backplate and
align it with the hole in the cover ring surrounding the
Danalock. Now you are sure to hit the notches on the
backplate with the Danalock.

Page 17
13. Fasten the Danalock
Turn the Danalock clockwise until it clicks to fasten it to
the backplate. NOTE: If you need to unfasten and retry,
see “Uninstall instructions” on p. 21.
Click!

Page 18
14. Activate batteries
Pull out the plastic tab to activate the batteries.
A light will ash to conrm the Danalock is ready.
Note: If the batteries are disconnected, you will have to
re-calibrate the Danalock.

Page 19
15. Before
completing the setup
Your Danalock is
now attached to
the door.
Leave the door
open, so the lock
isn’t inuenced
when calibrated.

Page 20
16. Open the Danalock app
Open the Danalock app you downloaded at the start.
When you have logged in you will see your empty
keychain. Press
”Add lock” at
the bottom
of the screen.
A guide will now
lead you through
the installation
and conguration
of your Danalock.
Addlock
SettingsLockusers LogMenu
You have no keys
Add your first lock
by pressing the
”Add lock” icon
below