danalock V3 BT HK SCANDI User manual

Danalock V3 BT HK EURO

2 3

4 5

6 7
X

8 9
=
X
7
22
10
25
15
32
x
x+

10 11

12 13



5
10
10

14 15
10mm
5 mm 15mm
10 mm 20mm
5+10 mm 25mm
10+10 mm 30mm
30 mm
10 mm
15 mm
20 mm
25 mm

16 17
10-35 mm

18 19
Click!

20 21
Click!

22 23
guide.danalock.com
The following instructions are in english. Localized versions can be
found with the QR-code below.

24 25
Add the Danalock in the HomeKit App
When the Danalock has been mounted on the door it is ready to
be set up with the Home app. Instructions on how to use the Home
app can be found at:
https://support.apple.com/en-us/HT204893
The HomeKit setup code can be found both inside the battery
compartment and on the ”Simple Guidelines” leaet.
Calibrate the lock
The Danalock needs to be
calibrated in order to function
properly. Calibration can be done
either automatically or manually
with the commands found on
page 27.
The Danalock can be congured
further with the commands found
on page 27 to 29.
Dismounting

26 27
LED-Mode LED color Status indication
Constant red till light nishes Lock has successfully locked
Constant green till light nishes Lock has successfully unlocked
Constant white for 3 seconds Power on. Batteries are activated
Red light ashes every 5 minutes Critical battery level
Constant purple Firmware is being updated
Blue light ashes Settings are changed/saved
LED-Signals Conguring the Danalock V3 with click-commands
You can congure the Danalock via the button found in the small hole on
the top of the lock. When you click through settings, the LED will change
color according to the following scheme. When you get
to the setting you want to change wait for 5 seconds and
the Danalock will react to your command. This gives you
plenty of time to navigate to the right command. If you
make a wrong number of clicks, just stop at a number
of clicks where the LED doesn’t light up and wait for
5 seconds. The LED will ash red to indicate that it has
timed out.
Clicks Color Activity
2Yellow Manual calibration
Start by turning the Danalock to the desired unlocked position. Start the calibration
with the click command and wait for the LED to start blinking yellow. Turn the
Danalock to the desired locked position while the LED blinks and click the button once
to save the locked position. The Danalock will conrm with a green blink.
If the lock doesn’t receive a response from you within 30 sec the calibration will be
canceled.
3White Auto calibration
Start by turning the Danalock to unlocked position and lifting the handle if needed. The
door has to be left open while the Danalock auto calibrates. Start the auto calibration
with the click command. The Danalock will blink white while auto calibrating.

28 29
Clicks Color Activity
4Blue Hold back latch
Toggles between 3 hold back latch settings: Off, short wait and long wait. Everytime
this command is entered the setting will switch to the next option.
• Off will respond with a red blink when being set, and will disable hold back latch.
• Short wait will respond with short green blinks when being set, and will hold the
latch back for 5 sec.
• Long wait will respond with one long green blink when being set and will hold the
latch back for 15 sec.
5Purple Auto lock timer
Toggles between 3 auto locking settings: Off, short wait and long wait. Every time this
command is entered the setting will switch to the next option.
• Off will respond with a red blink when being set, and will disable auto locking.
• Short wait will respond with short green blinks when being set, and will lock after
15 sec.
• Long wait will respond with one long green blink when being set and will lock after
60 sec.
6Cyan End to end unlock
Everytime this command is entered the setting will switch to the next option.
• Turning off will respond with one red blink when being set.
• Turning on will respond with one green blink when being set.
Clicks Color Activity
8Blue/Green blink Twist assist
Everytime this command is entered the setting will switch to the next option.
• Turning off will respond with one red blink when being set.
• Turning on will respond with one green blink when being set.
10 Red Reset user settings
This action will delete all user settings on the Danalock. The Danalock will respond by
blinking red.

30 31
Firmware upgrade
To install the latest rmware on your Danalock download the
Danalock app on App Store and log in as a ”HomeKit only” user.
Press the download icon on the front page in the app to start the
rmware upgrade process.
Make sure to keep your phone near the Danalock during the entire
rmware upgrade process.
Technical information
Controlling this HomeKit-enabled accessory automatically and
away from home requires an Apple TV with tvOS 10.0 or later or an
iPad with iOS 9.0 or later set up as a home hub.
HomeKit technology provides advanced security with end-to-
end encryption and authentication between a HomeKit-enabled
accessory and your iPhone, iPad, or iPod touch.
HomeKit security communications are encrypted between a
HomeKit-enabled accessory and your iPhone, iPad, or iPod touch.
Legal information
Use of the Works with Apple HomeKit logo means that an
electronic accessory has been designed to connect specically to
iPod touch, iPhone, or iPad, respectively, and has been certied by
the developer to meet Apple performance standards. Apple is not
responsible for the operation of this device or its compliance with
safety and regulatory standards. Apple, Apple Watch, iPad, iPad Air,
iPhone, and iPod touch are trademarks of Apple Inc., registered in
the U.S. and other countries. HomeKit is a trademark of Apple Inc.

www.danalock.com
Danalock International ApS
Gammel Stillingvej 427C
8462 Harlev, DK
[phone]
[email protected]
DV3-HK-EURO-EN-2018/10/03