Deltech Fitness DF832 User manual

DF832
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
PEC ATTACHMENT
Assembly Manual
ASSEMBLY VIDEOS AVAILABLE
Click on the QR Code below for your model to
access the assembly video
DF910– Lat Machine
DF908– Stack Loaded
Lat Machine

DF832
HARDWARE
QTY 1
DF832
INSTRUCTIONS
QTY 1
BOX CONTENTS
LEFT HAND ARM
QTY 1
K
RIGHT HAND ARM
QTY 1
J
FIXED PULLEY
BRACKET
QTY 1
B
SWIVEL PULLEY
BRACKET
QTY 2
C
RIGHT HAND CAM
QTY 1
E
LEFT HAND CAM
QTY 1
F
FLOATING PULLEY
BRACKET
QTY 1
G
SWIVEL PULLEY
MOUNT BRACKET
QTY 1
D
BACKREST PAD
QTY 1
I
ARM MOUNT
QTY 1
A
CABLE
QTY 1
L

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
LARGE BUSHING
QTY 8
N
SMALL BUSHING
QTY 8
O
3-1/2” PULLEY
QTY 7
P
M10 x 70MM BOLT
QTY 4
R
M10 x 45MM BOLT
QTY 4
S
M12 x 170MM
BOLT
QTY 2
Q
M10 x 25MM BOLT
QTY 2
U
M12 WASHERS
QTY 8
V
M10 WASHERS
QTY 18
W
M16 LOCK NUT
QTY 2
Y
M12 LOCK NUT
QTY 4
Z
M10 LOCK NUT
QTY 8
AA
M12 x 75MM BOLT
QTY 2
M
CHAIN
QTY 1
BB

ASSEMBLE THE ARM MOUNT (A) AND THE SWIVEL PULLEY MOUNT BRACKET (D) TO
THE FRONT SUPPORT OF THE LAT MACHINE USING THE M12 x 75MM BOLTS (M), M12
FLAT WASHERS (V) AND M12 LOCK NUTS (Z)
NOTE: THE NUTS USED ON THIS PRODUCT ARE LOCK NUTS SO YOU MUST USE A WRENCH TO TIGHTEN
THE BOLT. THE BOLT MUST GO THRU THE PLASTIC INSERT IN THE NUT.
TOOLS REQUIRED:
WRENCHES OR METRIC SOCKET SET
ARM & PULLEY MOUNT INSTALLATION
FRONT OF MACHINE
D
M V
V
A
Z

INSTALL THE CAMS (E,F) ON THE ARMS (J,K), INSERTING LARGE BUSHINGS (N) ON
EACH END OF THE TUBE. THERE IS A LEFT HAND AND A RIGHT HAND SIDE SO YOU WILL
NEED TO LOOK AT THE DIAGRAM TO ENSURE CORRECT INSTALLATION
CAM & ARM PAD ASSEMBLY
F
E
K
J
N
N
N
N

INSERT LARGE BUSHINGS (N) INTO THE ARM MOUNT (A). NOW ASSEMBLE THE WEIGHT
ARMS TO THE ARM MOUNT (A) USING THE M19 LOCKNUTS (Y)
ARM INSTALLLATION
Y
Y
N
N
A

SWIVEL PULLEY ASSEMBLY
SWIVEL PULLEY INSTALLATION
ASSEMBLE THE 3 ½” PULLEY (P) INTO
THE SWIVEL PULLEY BRACKET (C) USING
THE M10 x 45MM BOLT (S), M10 WASHERS
(W), AND M10 LOCKNUT (AA). REPEAT
FOR OTHER SWIVEL PULLEY ASSEMBLY.
INSTALL SMALL BUSHINGS (O) INTO
EACH END OF TUBE.
INSTALL THE SWIVEL PULLEY
ASSEMBLIES TO THE MOUNT BRACKET
USING THE M12 x 170MM BOLTS (Q), M12
WASHERS (V), SMALL BUSHINGS (O), AND
M12 LOCKNUTS (Z).
Q Q
V
V
V
V
Z
Z
P
Q
S
W
AA
W
O
O
O

ASSEMBLE THE BACKREST PAD (I) TO
THE FRONT SUPPORT OF THE LAT
MACHINE USING THE M10 x 70 BOLTS
(R) AND THE M10 FLAT WASHERS (X).
(THE BOLTS SCREW INTO THREADED
INSERTS PRE-INSTALLED IN THE BACK
PAD)
NEXT INSTALL THE FIXED PULLEY
ASSEMBLY USING THE M10 x 70MM
BOLTS (R) M10 FLAT WASHERS (W),
AND M10 LOCKNUTS (AA).
FIXED PULLEY ASSEMBLY
INSTALL THE 3 ½” PULLEY(P) INTO THE
FIXED PULLEY BRACKET (B) USING THE
M10 x 45MM BOLT (S) M10 WASHERS (W),
AND M10 LOCK NUT (AA).
NOTE: IF INSTALLING ON DF908, USE
4-1/2” PULLEY
FIXED PULLEY & BACKREST INSTALLATION
AA
P
S
W W
B
I
R
R
W
W
R
W
W
W
AA

ASSEMBLE THE 3 ½” PULLEY (P) TO THE FLOATING PULLEY BRACKET (G) USING THE
M10 x 45MM BOLT (S), M10 WASHERS (W) AND M10 NUT (AA).
FLOATING PULLEY ASSEMBLY
P
G
W
W
AA
S

FIGURE A
ATTACH THE PEC CABLE TO THE CAM ON THE LEFT SIDE USING THE M10 x 25MM BOLT
(W), M10 WASHERS (W) , AND M10 LOCKNUT (AA). (SEE FIGURE A)
NOTE: THERE ARE ADJUSTMENT HOLES ON EACH CAM TO COMPENSATE FOR CABLE
STRETCH AFTER THE MACHINE IS USED FOR A WHILE.
RUN THE CABLE THROUGH THE LEFT SIDE SWIVEL PULLEY, DOWN THROUGH THE
FLOATING PULLEY, UP THROUGH THE RIGHT SIDE SWIVEL PULLEY AND ATTACH TO
RIGHT CAM.
TIGHTEN THE BOLTS ON THE SWIVEL PULLEYS.
SWIVEL PULLEY ASSEMBLIES
FLOATING PULLEY ASSEMBLY
PEC ATTACHMENT CABLE INSTALLATION
U W
AA
W

REMOVE THE THE 4-1/2” PULLEY FROM THE CENTER FLANGES OF THE BOTTOM
SUPPORT AND REPLACE WITH 3-1/2” PULLEY.
INSTRUCTIONS FOR INSTALLING ON
DF838– STACK LOADED LAT ATTACHMENT

REMOVE THE 4-1/2” PULLEYS FROM THE FLOATING PULLEY ASSEMBLY AND
REPLACE WITH 3-1/2” PULLEYS, MAKING SURE TO INSTALL THE LOWER
BOLT IN THE HOLE SPECIFIED IN THE DIAGRAM ABOVE.
DF838 FLOATING PULLEY ASSEMBLY

DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT
SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC
USING THE CHAIN AND SPRING CLIPS PROVIDED.
DISCONNECT
LOWER CABLE
FROM HERE
RE-ATTACH LOWER
CABLE HERE USING SNAP
HOOKS AND CHAIN
DF838 LOWER CABLE INSTALLATION

MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM
ABOVE.
DF908 FLOATING PULLEY ASSEMBLY
INSTRUCTIONS FOR INSTALLING ON
DF908– STACK LOADED LAT MACHINE

DISCONNECT
LOWER CABLE
FROM HERE
RE-ATTACH LOWER
CABLE HERE
DF908 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT
SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC
WITH SPRING CLIP.

MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM
ABOVE.
DF830 FLOATING PULLEY ASSEMBLY
INSTRUCTIONS FOR INSTALLING ON
DF830– LAT ATTACHMENT

DISCONNECT
LOWER CABLE
FROM HERE
RE-ATTACH LOWER
CABLE HERE USING
SPRING CLIPS AND CHAIN
DF830 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT
SUPPORT. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY ON THE PEC DEC
USING THE CHAIN AND SPRING CLIPS PROVIDED.

MAKE SURE BOTTOM PULLEY IS MOUNTED AS SHOWN IN DIAGRAM
ABOVE.
DF910 FLOATING PULLEY ASSEMBLY
INSTRUCTIONS FOR INSTALLING ON
DF910– LAT MACHINE

DISCONNECT
LOWER CABLE
FROM HERE
RE-ATTACH LOWER
CABLE HERE USING
SPRING CLIPS
DF910 LOWER CABLE INSTALLATION
DISCONNECT THE END OF THE LOWER CABLE FROM THE FLANGE ON THE FRONT
SUPPORT AND REMOVE CHAIN. RECONNECT IT TO THE FLOATING PULLEY ASSEMBLY
ON THE PEC DEC USING SPRING CLIP. MOVE CHAIN TO UPPER CABLE AND CONNECT TO
WEIGHT CARRIAGE.
MOVE CHAIN
FROM LOWER
CABLE TO HERE

WARNING: THE USER OF THIS WEIGHT EQUIPMENT ASSUMES THE POSSIBILITY OF INJURY BY
EXERCISING ON THIS EQUIPMENT. THE POSSIBILITY OF RISK CAN BE REDUCED BY ALWAYS
FOLLOWING THESE SIMPLE RULES:
1) BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR DOCTOR FOR A COMPLETE PHYSICAL
EXAMINATION AND SUGGESTED EXERCISE PROGRAM SPECIFIC FOR YOU.
2) STRETCH BEFORE AND AFTER THE EXERCISE PROGRAM. PROPER STRETCHING WILL PREPARE YOUR
JOINTS AND MUSCLES FOR EXERCISE AND HELP AVOID INJURIES.
3) IF AT ANY TIME YOU SHOULD FEEL FAINT OR DIZZY, NAUSEOUS OR EXPERIENCE ANY OTHER
ABNORMAL SYMPTOMS OR DISCOMFORT DISCONTINUE USE AND CONSULT YOUR DOCTOR.
4) DO NOT USE THIS EQUIPMENT WITHOUT QUALIFIED SUPERVISION AND PROPER TRAINING. NEVER
WORK OUT ALONE- ALWAYS HAVE A PARTNER.
5) SECURELY TIGHTEN ALL BOLTS AND REGULARLY CHECK TO ENSURE ALL BOLTS HAVE NOT
LOOSENED.
6) WEAR GOOD RUBBER SOLE SHOES ONLY. DO NOT USE BARE FOOTED OR WITH SOCKS ONLY.
7) DO NOT WEAR LOOSE CLOTHES SUCH AS ROBES, GOWNS, PANTS, LONG SHIRTS OR JEWELRY WHICH
COULD BECOME ENTANGLED IN MOVING PARTS.
8) DO NOT STAND OR KNEEL ON SEAT. ALWAYS SIT OR LAY SQUARELY CENTERED.
9) KEEP HEAD, LIMBS AND BODY PARTS CLEAR OF MOVING PARTS AND WEIGHT PLATES.
10) CHILDREN SHOULD NOT USE EXERCISE EQUIPMENT WITHOUT SUPERVISION BECAUSE OF
POSSIBILITY OF INJURY FROM IMPROPER USAGE. THIS EQUIPMENT IS INTENDED FOR HOME USE ONLY.
11) REPLACEMENT OF WORN OR DEFECTIVE PARTS MUST BE WITH FACTORY AUTHORIZED PARTS. IF
OTHER THAN FACTORY AUTHORIZED PARTS OR ASSESSORS ARE USED ALL WARRANTIES AND
LIABILITIES BECOME VOID.
SAFETY NOTICE