Deltech Fitness DF910 User manual

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
LAT PULLDOWN MACHINE
Assembly Manual
DF910

BOX CONTENTS
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
REAR SUPPORT
QTY 1
A
FRONT SUPPORT
QTY 1
B
BOTTOM FRAME
QTY 1
C
REVOLVING CHROME
ROW BAR
QTY 1
D
LAT CABLE
QTY 2
E
FOOT PLATE
QTY 1
C1
FOOT REST
QTY 1
C2

LAT BAR
QTY 1
F
*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
BOX CONTENTS
SEAT SUPPORT
QTY 1
J
SEAT BRACKET
QTY 1
I
UPPER PULLEY
FRAME
QTY 1
G
SEAT PAD
QTY 1
H
REAR CROSSMEMBER
QTY 1
N
HOLD-DOWN SUPPORT
QTY 1
M
HOLD-DOWN
TUBE
L
WEIGHT SLIDE
QTY 1
K
ROLLER PAD
QTY 2
P
FLANGE
QTY 2
Q
BOTTOM PULLEY
FRAME
QTY 1
R

*NOTE IF YOU ARE MISSING HARDWARE OR HAVE ANY FIT UP PROBLEMS PLEASE CONTACT DELTECH FITNESS TOLL FREE [phone]
FOR YOUR SAFETY READ ALL INSTRUCTIONS CAREFULLY
[phone]
HARDWARE
S
MUSHROOM CAP
QTY 2
4-1/2” PULLEY
QTY 3
U
3-1/2” PULLEY
QTY 4
PULLEY BUSHING
QTY 6
SNAP HOOK
QTY 6
CHAIN
QTY 2
OLYMPIC ADAPTER
QTY 2
M12 x 70MM BOLT
QTY 2
AA
M10 x 45MM BOLT
QTY 4
DD
EE
M10 x 20MM BOLT
QTY 2
FF
M10 x 70MM
FLAT HEAD BOLT
QTY 3
RUBBER SHOE
QTY 2
T V
W X Y Z
M12 x 65MM BOLT
QTY 2
BB
M10 x 70MM BOLT
QTY 3
CC
GG
M10 x 65MM
CARRIAGE BOLT
QTY 9

HARDWARE
KK
M10 LOCKNUT
QTY 19
M12 WASHER
QTY 8
HH
M10 WASHER
QTY 20
I I JJ
M12 LOCKNUT
QTY 4
OLYMPIC COLLAR
QTY 2
LL
STANDARD COLLAR
QTY 2
MM

LAY BOTTOM FRAME (C) ON ITS SIDE ON LEVEL FLOOR. INSTALL FRONT & REAR
SUPPORTS (A), (B) TO BOTTOM FRAME (C) USING THE M10 x 65MM
CARRIAGE BOLTS (GG), M10 WASHERS (II), AND M10 LOCKNUTS (KK).
INSTALL BOTTOM PULLEY FRAME (R), HOLD-DOWN SUPPORT (M), AND SEAT
SUPPORT (J) TO BOTTOM FRAME (C) USING THE M10 x 65MM CARRIAGE BOLTS
(GG), M10 WASHERS (II), AND M10 LOCKNUTS (KK).
TOOLS REQUIRED:
METRIC WRENCHES OR SOCKET SET
Some components may be pre-installed
from the factory
(NOTE: THE NUTS USED ON THIS
BENCH ARE LOCK NUTS, THIS MEANS
YOU MUST TIGHTEN THEM DOWN
PAST THE PLASTIC INSERT.)
A
B
R
M
J
C
GG
I I KK

ROTATE THE ASSEMBLY TO THE UPRIGHT POSITION AND SLIDE THE REAR
CROSSMEMBER (N) INTO PLACE AND INSTALL TO THE BOTTOM FRAME USING
THE M12 x 70MM BOLTS (AA), M12 WASHERS (HH), AND M12 LOCKNUTS (JJ).
INSTALL THE RUBBER BOOTS (T) OVER THE ENDS OF THE CROSSMEMBER.
ATTACH THE FOOT PLATE (C2) AND FOOT REST (C1) TO THE BOTTOM FRAME
USING M10 x 70 MM FLAT HEAD BOLTS (FF), M10 WASHERS (II), AND M10 LOCK-
NUTS (KK).
AA
T
T
N
HH
HH
JJ
KK
I I
FF
C2
C1

INSTALL THE WEIGHT SLIDE ASSEMBLY (K) ONTO THE REAR SUPPORT.
ASSEMBLE THE UPPER PULLEY FRAME ONTO THE FRONT AND REAR SUPPORTS
USING THE M12 x 65MM BOLTS(BB), M12 WASHERS (HH), AND M12 LOCKNUTS (JJ).
K
JJ
HH
HH
BB
JJ
HH
HH
BB
G

ATTACH THE SEAT PAD (H) TO THE SEAT BRACKET (I) USING THE M10 x 20MM
BOLTS (EE) AND M10 FLAT WASHERS (II). THEN SLIDE THE SEAT BRACKET (I)
INTO THE SEAT SUPPORT (J).
INSTALL THE 3 ½” PULLEY (V) INTO THE SEAT SUPPORT TUBE (J) USING THE
M10 x 45MM BOLT (DD) , M10 WASHERS (II), AND M10 LOCK NUT (KK).
SEAT FRAME ASSEMBLY
H
I
EE
I I
J
V
DD
I I
I I
KK

SLIDE THE HOLD-DOWN TUBE (L) INTO THE HOLD-DOWN SUPPORT (M) . LOCK
INTO PLACE WITH PULL-PIN.
SLIDE THE ROLLER PADS (P) OVER THE LEG PAD TUBE AND INSERT THE MUSH-
ROOM CAPS (S). TAP INTO PLACE WITH A RUBBER HAMMER.
LEG HOLD DOWN ASSEMBLY
L
M
S
P
S
P

BOTTOM PULLEY FRAME ASSEMBLY
ASSEMBLE THE 4 ½” PULLEY (U) INTO THE BOTTOM PULLEY FRAME (R) USING
THE M10 x 45MM BOLT (DD), M10 WASHERS (II), AND M10 LOCKNUT (KK).
U
R
KK
I I
I I
DD

FLOATING PULLEY ASSEMBLY
ASSEMBLE THE FLOATING PULLEY ASSEMBLY BY USING 4-1/2” PULLEYS (U),
FLANGES (Q), M10 x 45MM BOLTS (DD), M10 WASHERS (II), AND M10 LOCKNUTS (KK).
I I
I I
KK
Q
DD
U

UPPER CABLE INSTALLATION
THE UPPER AND LOWER CABLES ARE THE SAME.
STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE INTO FRONT
OPENING OF THE UPPER PULLEY FRAME AND FEED IT TOWARDS THE BACK. PULL CABLE
END OUT THROUGH REAR OPENING.

UPPER CABLE INSTALLATION
INSERT 3-1/2” PULLEY (V) INTO FRONT OPENING OF UPPER PULLEY FRAME AND INSTALL
USING THE M10 x 70MM BOLT (CC), PULLEY BUSHINGS (W), AND M10 LOCKNUT
(KK). REPEAT FOR MIDDLE PULLEY.
CC
KK
W
W
V
V

UPPER CABLE INSTALLATION
FEED CABLE END AROUND TOP PULLEY OF FLOATING PULLEY ASSEMBLY AND THEN
OVER 3-1/2” PULLEY. INSTALL 3-1/2” PULLEY IN UPPER PULLEY FRAME USING THE M10 x
70MM BOLT (CC), PULLEY BUSHINGS (W), AND M10 LOCKNUT (KK).
CC
W
W
KK

UPPER CABLE INSTALLATION
ATTACH SNAP HOOKS TO BOTH ENDS OF CHAIN. ATTACH ONE END TO CABLE AND THE
OTHER END TO MOUNTING FLANGE ON WEIGHT SLIDE.

LOWER CABLE INSTALLATION
STARTING WITH THE CABLE END WITHOUT THE BALL, INSERT CABLE UNDER 3-1/2”
PULLEY ON SEAT FRAME. MAKE SURE THAT CABLE IS BELOW PULLEY AND ABOVE
KEEPER BAR ON BOTTOM OF PULLEY FRAME (SEE INSET PICTURE)
KEEPER BAR

LOWER CABLE INSTALLATION
FEED CABLE THROUGH OPENINGS IN SEAT SUPPORT, HOLD-DOWN SUPPORT, AND FRONT
SUPPORT. INSTALL CABLE AROUND 4-1/2” LOWER PULLEY, UP AND AROUND BOTTOM
PULLEY OF FLOATING PULLEY ASSEMBLY AND DOWN TO MOUNTING FLANGE AT BOTTOM
OF FRONT SUPPORT. ATTACH SNAP HOOK TO END OF CABLE AND ATTACH TO MOUNTING
FLANGE.

ATTACH LAT BAR TO UPPER CABLE WITH SNAP HOOK. MOVE TO CRADLE WHEN NOT IN
USE.
LAT BAR INSTALLATION
ATTACH LOW ROW BAR TO LOWER CABLE WITH 2 SNAP HOOKS AND CHAIN. YOU CAN
ALSO USE THIS CHAIN ON THE HIGH PULLEY TO DO TRICEP EXERCISES.
LOW ROW BAR INSTALLATION