Denali LAH.07.10401 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
Driving Light Mount
BMW R 1250 GS 2019-
LAH.07.10401
Instruction Manual
(a) Light Mounting Bracket.........................................................Qty 1
(b) M8x110 DIN 912.................................................................Qty 2
(c) M8 Washer DIN 9021............................................................Qty 4
(d) Spacer, ID: 9mm OD: 25mm L: 80mm....................................Qty 2
(e) M8 Nut DIN 985..................................................................Qty 2
Kit Contents
Tools Required: 6mm Allen Key, 13mm Wrench
(a)
(c)
(b)
(d)
(e)

1. Installing The Light Mount
1.1 - Insert The Mounting Bolts
Step One: Place one M8x110 Screw (b) and M8 Washer (c) into each hexagon shaped
opening found on either side of the headlight.
Note: You only need to loosen the bolts holding the body panels in place. This will give
you enough flex to slide the bolts into place.
DENALIELECTRONICS.COM
1.2 - Installing The Mounting Bracket
Step One: Place a Spacer (d) over each M8 Screw (b) protuding from the underside of
the front fender.
Step Two: Use the M8 Washers (c) and M8 Nuts (e) to attach the Mounting Bracket (a)
to the motorcycle. The light mounting tabs should face towards the front of the bike.