Denali LAH.07.11000 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
Auxiliary Light Mounting Brackets
Select BMW Models (OEM Light Mount Adapter)
LAH.07.11000
Instruction Manual
(a) OEM Light Mount Adapter......................................................Qty 2
(b) M6x14 ISO 7380.................................................................Qty 4
Kit Contents
Tools Required: 13mm Wrench, 10mm Wrench, 4mm Allen Key, T25
Torx Driver
(a)(a)
(b)

1. Light Mount Adapter Installation
1.1 - Removing The OEM Light Mount
Step One: Use a T25 Torx tool to loosen the two OEM Screws located on the underside
of the OEM Light Mounting Bracket until the bracket rotates freely on the Mounting Post.
Step Two: Slide the OEM Light Mounting Bracket off of the Mounting Post.
Step Three: Remove the OEM Light Pod from the OEM Light Mounting Bracket.
Note: (OEM Light Pod Not Illustrated)
DENALIELECTRONICS.COM
1.2 - Attaching The Light Pod
Step One: Use a 13mm Wrench and the hardware that was supplied with the light pod
to attach the OEM Light Mount Adapter (a) to the light pod.
2.1 - Attaching The Light Mount Adapter
Step One: Use a 4mm Allen key and two M6x14 screws (b) to attach the OEM Light
Mounting Bracket to the OEM Light Mount Adapter (a).
2.2 - Installing the Light Pod
Step One: Slide the OEM Light Mounting Bracket back onto the Mounting Post.
Step Two: Use T25 Torx tool to tighten the two OEM Screws on the underside of the
OEM Light Mounting Bracket until the bracket no longer rotates on the Mounting Post.
(a)
Example Light Pod
(a)
OEM Light Mounting Bracket
(b)
OEM Light Mounting Bracket
OEM Screws
OEM Screws
Mounting Post
OEM Light Mounting Bracket
Mounting Post