Denali LAH.07.11300 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
Auxiliary Light Mounting Bracket
BMW G310GS 2018-Present
LAH.07.11300
Instruction Manual
(a) Left Side Mounting Bracket....................................................Qty 1
(b) Right Side Mounting Bracket..................................................Qty 1
(c) M5x20 ISO 7380..................................................................Qty 2
(d) M5 Washer DIN 125.............................................................Qty 4
(e) M5x20 DIN 933...................................................................Qty 2
(f) Spacer - OD: 15.8mm, ID: 6.5mm, L: 6.3mm..........................Qty 2
(g) M8x14 DIN 933...................................................................Qty 1
Kit Contents
Tools Required: 13mm Wrench, 8mm Wrench, 3mm Allen Key
(b)
(a)
(c)
(e)
(g)
(d)
(f)

1. Installing The Light Mount
1.1 - Removing The Horn
Step One: Remove the horn from the underside of the front fairing by unscrewing the
M8 mounting bolt.
DENALIELECTRONICS.COM
1.2 - Mounting The Left Side Bracket
Step One: Remove the two factory bolts from the mounting points.
Step Two: Use the M5x20 Lens Head (c), Washer (d) and Spacer (e) to attach the Left
Side Bracket (a) to the outer mounting point.
Step Three: Use the M5x20 Hex Head (f) and Washer (d) to fasten the bracket (a) at
the inner mounting point.
2.1 - Mounting The Right Side Bracket
Step One: Remove the two factory bolts from the mounting points.
Step Two: Use the M5x20 Lens Head (c), Washer (d) and Spacer (e) to attach the Right
Side Bracket (b) to the outer mounting point.
Step Three: Use the M5x20 Hex Head (f) and Washer (d) to fasten the bracket (b) at
the inner mounting point.
2.2 - Re-installing The Horn
Step One: Re-install the horn using the supplied M8x14 bolt (g).
Note: It may be necessary to loosen the 10mm nut on the back of horn and rotate the
horn on its bracket to gain clearance for the horn connectors.
Horn M5x20 Hex
M5x20 Lens
Washer
Spacer
M5x20 Hex
Spacer
Washer
M5x20 Lens
RHS Bracket
LHS Bracket
Factory Bolt
M8x14
Horn