Denali HMT.07.11001 User manual

Instruction Rev00
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
HMT.07.11001
BMW R1250GS
Split Horn Mounting Bracket
Instruction Manual
(a) M8x75mm - SocketHead Screw..............................................Qty 2
(b) M8 Washer..........................................................................Qty 2
(c) Acoustic Horn Bracket......(HMT.07.014)..................................Qty 1
(d) M8 Spacer...OD 19.05mm, ID 8.1mm, L 19.05mm....................Qty 2
(e) M6x30mm - Socket Head Screw.............................................Qty 2
(g) M6 Washer..........................................................................Qty 2
(g) Compressor Mount .....(HMT.07.013)......................................Qty 2
Kit Contents
Tools Required: 6mm Allen Key, 5mm Allen Key
Compatibility: SoundBomb Split Horn
(a)
(b)
(c)
(f)
(g)
(e)
(d)

1. Installing The Compressor DENALIELECTRONICS.COM
Step Five: Route the hose down the left side and underneath the bottom of the
compressor, then wedge it in the gap between the right side of the compressor and the
bracket. The remainder of the hose should be channeled up under the side fairing and
forward through towards the front shock. Once through to the front, the hose end
should be routed up behind the steering head through the tubular frame sideways
towards the right side where it can be connected to the acoustic unit .
Step Six: Route the horn wiring harness down into the same channel between the right
side of the compressor and the bracket where the hose is wedged. Connect the wire
leads to the bottom of the compressor when ready.
1.3 - Installing The Compressor
Step One: Install the hose end onto the compressor, making sure it is all the way on and
secure.
Step Two: Use the horn provided hardware (M8 Hex bolt, M8 Nut) and a 13mm wrench to
secure the compressor to the Bracket (g).
Step Three: Locate both of the mounting points on the engine case on the left hand side of
the bike and remove the factory bolts.
Step Four: Mount the Compressor Bracket (g) and compressor to the mounting locations
using the two M6x30mm screws (e) and two M6 Washers (f).

Step Four: Take the remaining end of the hose and install it onto the top of the acoustic
unit, firmly press down to make sure it is all the way on and secure.
Step Five: Mount the acoustic unit to the installed bracket-A using the horn’s included
hardware (M6 Hex Bolt, dampener, M6 nut) and a 10mm wrench.
NOTE: The hex head should be slid all the way up to the top of the slot.
DENALIELECTRONICS.COM
1.1 - Installing the Acoustic Unit
Step One: Start by removing the upper M8 mounting bolt from the right side of the
upper fairing stay. Do not remove the lower bolt yet.
Step Two: Using the M8x75 Socket head (a), M8 Washer (b), and M8 Spacer (d) secure
the top hole of Acoustic Bracket (c) to the upper mounting hole on the fairing stay and
hand tighten with a 6mm allen.
Step Three: Rotate the bracket (c) counterclockwise until there is clearance to remove
the lower factory mounting bolt. Next reposition the bracket and secure it to the lower
mounting location with the remaining M8x75mm bolt (a), M8 Washer (b) , and M8
Spacer (d). Properly tighten both bolts.
1. Installing The Acoustic Unit DENALIELECTRONICS.COM