Denali LAH.01.10700 User manual

Instruction Rev04
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
LAH.01.10700
Honda Africa Twin 1100
Light Mounting Brackets
Instruction Manual
(a) LAH.01.010..Horizontal Support Arm......................................Qty 1
(b) LAH.01.011...Right Side Brace...............................................Qty 1
(c) LAH.01.012...Left Side Brace.................................................Qty 1
(d) M8 x 40mm Button Head Srew...............................................Qty 2
(e) M8 washer..........................................................................Qty 2
(f) M8 Locking Nut....................................................................Qty 2
(g) M5 x 12mm Socket Head Screw.............................................Qty 2
(h) M5 Washer..........................................................................Qty 2
(i) M5 x 16mm Counter Sink Srew...............................................Qty 2
(j) M5 Locking nut....................................................................Qty 2
Kit Contents
Tools Required: 13mm Wrench, 8mm Wrench, 5mm Allen Key, 4mm
Allen Key, 3mm Allen Key.
(a)
(b)
(c)
(h)
(f)
(g)
(i)
(j)
(e)
(d)

1. Installing The Light Mount DENALIELECTRONICS.COM
1.2 - Installing Horizontal Support Arm
Step One: Using the two M5 countersink screws (i) and M5 nuts (j) secure the
Horizontal support arm (a) to the underside of the bent tabs on your installed braces
(b,c), you’ll need an 8mm wrench and a 3mm hex bit.
1.1 - Installing Braces
1.3 - Securing the Support Arm
Step One: On the bottom side of the plastic cover below the lights there are two circles,
one on either side indicated with arrows, and behind them on the inside of the cover are
two mounting points. Remove the factory screws from these locations.
Step Two: Rotate the combined bracket upwards to align the top mounting holes on the
braces with the top hole on the upper fairing stay. Securely tighten both bolts using a
13mm wrench and 5mm hex bit.
Step Three:Using the two M5 socket heads (g) secure the slots in the vertical tabs on
either side of the support arm to the mounting points on the inside of the plastic cover.
NOTE: In order to slip the two horizontal tabs on the support arm (a) into place, you
may need to slightly flex the bracket or the plastic cover below the lights to get past it.
Step One: Start by removing the factory mounting bolts from the right side of the
upper fairing stay.
Step Two: Using the M8x40mm Button head (d), M8 Washer (e), and M8 Nut (f)
secure both braces (b,c) to either side of the fairing stay through the lower mounting
hole and hand tighten, leaving the braces angled down.
DENALIELECTRONICS.COM

2. Installing The Light Mount DENALIELECTRONICS.COM
1.4 - Mounting Lights to the Bracket
Step One: Locate the mounting holes on the far ends of the support arm and secure
your LED Light Pods using the lights provided hardware.
Note: For ease of installation you may have to remove the swivel bracket from your
light pod and secure that first.