Denali LAH.23.10200 User manual

Instruction Rev03
0mm 10 20 30 40 50 60 70 80 90
Thank you for choosing DENALI
We know you would rather be riding your bike than wrenching on it, so we go the extra
mile to make sure our instructions are clear and as easy to understand as possible. If
you have any questions, comments, or suggestions don’t hesitate to give our gear
experts a call at 401.360.2550 or visit WWW.DENALIELECTRONICS.COM
Please Read Before Installing
DENALI products should always be installed by a qualified motorcycle technician. If
you are unsure of your ability to properly install a product, please have the product
installed by your local motorcycle dealer. DENALI takes no responsibility for damages
caused by improper installation. Caution: When installing electronics it is extremely
important to pay close attention to how wires are routed, especially when mounting
products to the front fender, front forks, or fairing of your motorcycle. Always be sure
to turn the handlebars fully left, fully right, and fully compress the suspension to
ensure the wires will not bind and have enough slack for your motorcycle to operate
properly.
Installation Tips
We strongly recommend using medium strength liquid thread locker on all screws,
nuts, and bolts. It is also important to ensure that all hardware is tightened to the
proper torque specifications as listed in your owner’s manual. For included accessory
hardware please refer to the default torque specifications provided below. Inspect all
hardware after the first 30 miles to ensure proper torque specifications are
maintained.
Hardware Sizing Guide
Not sure what size bolt you have? Use this ruler to measure screws, bolts, spacers, etc.
Remember, the length of a screw or bolt is measured from the start of the “mounting
surface” to the end of the screw, so only include the screw head when measuring
countersunk screws.
M3 10.0 in-lbs - 1.0 Nm
M4 23.0 in-lbs - 2.5 Nm
M5 44.5 in-lbs 3.5 ft-lbs 5.0 Nm
M6 78.0 in-lbs 6.5 ft-lbs 9.0 Nm
M8 - 13.5 ft-lbs 18.0 Nm
M10 - 30.0 ft-lbs 41.0 Nm
M12 - 52.0 ft-lbs 71.0 Nm
in-lbs
ft-lbs NmBolt Size
0in 1 2 3
What’s In The Box?
DENALIELECTRONICS.COM
LAH.23.10200
Harley Davidson Pan America
Front T3 Mounting Bracket
Instruction Manual
(a) T3 Mounting Bracket-R......(DNL.T3.018)................................Qty 1
(b) T3 Mounting Bracket-L......(DNL.T3.019)................................Qty 1
(c) M3x10mm DIN 912 Socket Head Screw...................................Qty 4
(d) M6x20mm DIN 912 Socket Head Screw...................................Qty 2
(e) DIN 9021; Oversized Washer OD 18mm ID 6.4mm H1.6mm......Qty 2
(f) M6 Washer DIN 125 .............................................................Qty 2
(g) M6 Locking Nut...................................................................Qty 2
Kit Contents
Tools Required: 5mm Hex, 2.5mm Hex, 10mm wrench
(a)
(b)
(c)
(f)
(g)
(e)
(d)

1. Installing The Light Mount DENALIELECTRONICS.COM
Driving
Direction
1.1 - Location Prep & Installation
Step One: Remove the side fairings on either side of the radiator guard that cover the
factory turn signals. They're connected to the bike via screws on the back of the
housing.
Step Two: The side fairings have two connected sections, remove the inner screws and
seperate the two plastics to gain access to the factory lights. From here you can
disconnect and remove the factory turn signals.
Step Three: Using the M3x10mm Socket head screws(c) and 2.5mm Hex Wrench
mount the T3 Pods on to the bracket (a,b). While the Side fairing is disassembled you
can route the cables through the same inner track as the factory turn signals.
Step Four: In the same mounting location as the factory turn signal you can now mount
the front T3 Bracket & Pod. Secure the bracket(a,b) in place with the M6x20mm Socket
Head Screw(d) and Oversized Washer(e) on top and the standard M6 Washer(f) and
Locking Nut(g) below.
Step Five: Reassemble the plastic cover to the side fairing and reattach it to the bike.