Drive PHOENIXHD3 User manual

1
PHOENIX HD SCOOTER
PHOENIXHD3 / PHOENIXHD4
OWNER’S MANUAL

2
1.
PREFACE AND INTRODUCTION ……..……………………………………
3
2.
SAFETY NOTICE…………………………………………………………...….
2.1 Before driving
2.2 While driving
2.3 Labeling
2.4 EMI
4
3.
4.
PARTS INTRODUCTION……………..……………….. …………………….
OPERATION…………………………………………………………………....
4.1 Control panel
4.2 How to operate your scooter
4.3 How to set to freewheel mode
9
10
5.
DRIVING ON THE ROAD……………………………………………………..
15
6.
BATTERY CHARGINGAND CARE……………………………………….....
6.1 Charging the battery
6.2 Battery
6.3 Replacing batteries
16
7.
INSPECTION AND MAINTENANCE……………………………………..…
7.1 Inspection
7.2 Regular checking record
7.3 Battery and tire
7.4 Storage
7.5 Moving about
7.6 Disassembly
7.7 Assembly
20
8.
TROUBLESHOOTING ……………………………..……………..…………
25
9.
SPECIFICATION …………….………………………………………..………
26
10.
WARRANTY………………………………………………………………….....
27
TABLE OF CONTENTS

3
Please carefully read this owner’s manual before using the vehicle. Improper use of the
vehicle could result in harm, injury or traffic accidents. To ensure that you get the most
your scooter, please read this owner’s manual before using.
This owner’s manual includes operation instructions for every aspect of the vehicle,
assembly instructions, as well as instructions for how to deal with possible accidents.
The symbols used in this manual are explained overleaf:
Warning
Improper usage could result in serious injury or death
Attention
Improper usage could lead to injury and/or damage to your scooter.
Suggestion
Follow these instructions to keep your vehicle in a good operating
order.
This manual includes a copy of repair and maintenance record chart and warranty
information. Please keep it in a safe place or in the scooter.
If someone else uses the scooter, please make sure that you provide himor her with this
owner’s handbook for his or her consideration.
As designs change some illustrations and pictures in the manual may not correspond to
the vehicle that you purchased. We reserve the right to make design modifications.
Our Scooters have been designed and manufactured to provide a comfortable and secure
yet affordable solution for some mobility requirements.
1 . P R E FA C E A N D I N T R O D U C T I O N

4
2 . S A F E T Y N O T I C E
2.1 BEFORE DRIVING
The user needs to be familiar with the usage and operation of this vehicle before driving.
Therefore, please follow the commendations in this safety notice.
■The same traffic rules apply to the use of this vehicle as apply to pedestrians
For your safety, please follow and adhere to the same traffic laws as pedestrians.
Please do not drive your scooter after consuming alcohol or when you are tired.
Please be careful when driving your scooter in low light. It has not been designed for
use at night.
Be extremely cautions when driving you scooter in busy areas or in shopping malls.
Ride on the pavement, single carriage roads, or pedestrian areas only. Never ride on
motorways or dual carriageways.
Be aware of traffic when crossing or using roads.
■Practice operating your vehicle
Before using the scooter in busy or potentially dangerous areas, familiarize yourself with
the operation of your scooter. Please practice in a wide and open area like a park. In order
to avoid accidents with your scooter whilst driving, please bear in mind driving motions,
such as accelerating, stopping, turning, reversing, up-and down ramps.
Please turn the speed dial to minimum value for your initial practice.
Be sure someone accompanies you for safety when driving on the roads for the first
time.
Only use higher speed setting when you are confident that you can easily operate and
control your scooter.
■The Scooter is only to be used by one person at a time
Do not carry passengers on your scooter (including children)
■Do not use this vehicle to carry or haul goods
The maximum weight that can be carried is 160kg / 350 lbs (including occupant and
any goods).Refer to “MAX LOAD WEIGHT”in “9. SPECIFICATION”
Maximum loading weight for basket is 3kg (7 lbs).
■Please carry out daily inspections.
Refer to the section entitled “DAILY CHECKING”

5
2 . S A F E T Y N O T I C E
2.2 WHILE DRIVING
■Do not use your vehicle under the circumstances below.
On surfaces that are muddy, gravelly, bumpy, narrow, snowed over, icy, or canal
towpaths not guarded by any fence or hedge. Keep awayfrom places where you might
get the wheels stuck.
Do not drive at night or when it is raining, snowing, misty, or windy.
Do not drive your vehicle in an “S”pattern or make erratic turnings.
Do not take the scooter onto escalators.
UNDER NO CIRCUMSTANCES SHOULD THE SCOOTER BE USED AS ASEAT
IN A MOTOR VEHICLE (E.G. CARS, BUSES, TRAINS, ETC).
■About Mobile Phones and other electrical equipment
Do not use a mobile phone or other wireless communication devices while driving.
Always switch off the scooter and remove the ignition key before using a mobile
phone.
Do not charge the mobile phone or any other electrical devices from your scooter’s
battery.
■Automatic Power Shut Down
In order to avoid accidental battery run down, your scooter is equipped with an
automatic power shut down facility. If the scooter is switched on, after remaining
undisturbed for a period of thirty minutes it will automatically turn off. When this
situation occurs, simply switch your scooter off and back on and it will be ready to use
once again.
■Ramps, inclines and drops
Do not drive onto steep ramps greater than the specified gradient. Refer to the section
entitled “CLIMBING ANGLE”in “9. SPECIFICATION“
Always use a low speed setting when ascending or descending a gradient.
Do not drive on roads with large drops or potholes. Refer to the section entitled
“MAX. GROUND CLEARANCE”in “9. SPECIFICATION”.
Please slow down when driving on roads with inclines.
Do not make sudden turns when driving on gravel roads or ramps.
Always lean forward when climbing a steep gradient.
Do not travel on gradients exceeding those stated on the diagram overleaf.

6
lbs
8°
20 lbs
7°
lbs
6°
Figure1. Maximum Recommended lncline Angles
READ OWNER'S MANUAL
AND CHARGE BATTERY
BEFORE OPERATING
WARNING
Do not exceed recommended
inclines or weight limits.
scooter is motion.
Never attempt to adjust the tiller while the
tightened.
certain the tiller adjustment knob is fully
Before lifting or driving the scooter make
tiller adjustment knob.
Please hold the tiller before loosening the
WARNING
2 . S A F E T Y N O T I C E
2.3 Labeling
Please carefully read all the labeling on the scooter before drive it. For your future
reminding, do not remove them.

7
2 . S A F E T Y N OT I C E
2.4 EMI
This portion of the content will provide the user with basic information that describes the
problems with EMI, known sources of EMI, protective measures either to lessen the
possibility or exposure or to minimize the degree of exposure, and suggested action
should unexpected or erratic movement occur.
Caution: It is very important that you read this information regarding the possible
effects of electromagnetic interference on your electric SCOOTER.
■ELECTROMAGNETIC INTERFERENCE (EMI) FROM RADIO WAVE
SOURCES
Powered vehicle may be susceptible to electromagnetic interference (EMI), which is
interfering electromagnetic energy (EM) emitted from sources such as radio stations, TV
stations, amateur radio (HAM) transmitters, two-way radios, and mobile phones. The
interference (from radio wave sources) can cause the powered scooter to release its
brakes, move byitself, or move in unintended directions. It can also permanently damage
the powered scooter’s control system. The intensity of the interfering EM energy can be
measured in volts per meter (V/m). Each powered scooter can resist EMI up to a certain
intensity. This is called its “immunity level”. The higher the immunity level, the greater
the protection. At this time, current technology is capable of achieving at least a 20 V/m
immunity level, which would provide useful protection from the more common sources
of radiated EMI. This powered scooter model as shipped, with no further modification,
has an immunity level of 20 V/m without any accessories.
There are a number of sources of relatively intense electromagnetic fields in the everyday
environment. Some of these sources are obvious and easy to avoid. Others are not
apparent and exposure is unavoidable. However, we believe that by following the
warning listed below, your risk to EMI will be minimized.
The sources of radiated EMI can be broadly classified into three types:
1. Hand-held portable transceivers ( transmitter -receivers with the antenna mounted
directly on the transmitting unit. Examples include: citizens band (CB) radios,
“walkie talkie”, security, fire, and police transceivers, cellular telephones and other
personal communication devices.
Note: Some mobile telephones and similar transmit signal while they are ON, even
when not being used;
2. Medium-range mobile transceivers, such as those used in police cars, fire trucks,
ambulances and taxis. These usually have the antenna mounted on the outside of the
scooter.

8
2 . S A F E T Y N OT I C E
3. Long-range transmitters and transceivers, such as commercial broadcast transmitter
(radio and TV broadcast antenna towers) and amateur (HAM) radios.
Note: Other types of hand-held devices, such as cordless phones, laptop computers,
AM/FM radios, TV sets, CD player, and cassette players, and small appliances,
such as electric shavers and hair dryers, so far as we know, are not likely to
cause EMI problems to your powered scooter.
■POWERED VEHICLE ELECTROMAGNETIC INTERFERENCE (EMI)
Because EM energy rapidly becomes more intense as one moves closer to the
transmitting antenna (source), the EM fields from hand-held radio wave sources
(transceivers) are of special concern. It is possible to unintentionally bring high levels
of EM energy very close to the control system of power chair while using these devices.
This can affect powered vehicle movement and braking. Therefore, the warnings listed
below are recommended to prevent possible interference with the control system of the
powered scooter.
■WARNINGS
Electromagnetic interference (EMI) from sources such as radio and TV stations,
amateur radio (HAM) transmitters, two-way radios, and mobile phones can affect
powered scooter and motorized scooter. Following the warnings listed below should
reduce the chance of unintended brake release or powered scooter movement which
could result in serious injury.
1. Do not operate hand-held transceivers-receivers), such as citizens band (CB) radios,
or turn ON personal communication devices, such as cellular phones, while the
powered vehicle is turned ON;
2. Be aware of nearby transmitters, such as radio or TV stations, and try to avoid
coming close to them;
3. If unintended movement or brake release occurs, turn the powered vehicle OFF as
soon as it is safe;
4. Be aware that adding accessories or components, or modifying the powered vehicle,
may make it more susceptible to EMI ( Note: There is no easy way to evaluate their
effect on the overall immunity of the powered scooter).
5. Report all incidents of unintended movement or brake release to the powered
scooter manufacturer, and note whether there is a source of EMI nearby,
IMPORTANT INFORMATION
1. 20 Volts per meter ( V/m) is a generally achievable and useful immunity level against
EMI ( the higher the level, the greater the protection);
2. This product has an immunity level of 20 V/m without any accessories and connected
to it.

9
3 . PA R T S I N T R O D U C T I O N
PARTS DESCRIPTION
1. Control panel
2. Basket
3. Charger Socket
4. Tiller Adjustment Knob
5. Seat
6. Seat Rotation Lever
7. Battery Pack
8. Freewheel Lever
9. Anti-tip wheels
10. Seat Post Knob
11. Seat HeightAdjustment
Pin

10
4 . O P E R AT I O N
4.1 CONTROL PANEL
1. Speed Dial 2. Horn Button
3. Battery Indicator 4. Power Switch
5. Power Eye
4.2 HOW TO OPERATE YOUR SCOOTER
■Power switch
To switch the power on , turn the key
clockwise in the ignition. The power eye should illuminate.
To switch the power off, turn the key anticlockwise. The power eye should switch off
and the key can be removed if required.
■Speed Dial
Turn the speed dial to determine the maximum
speed of the scooter. Turn the dial clockwise to
increase the speed setting and turn the dial
anticlockwise to decrease the speed setting.
■Moving and Braking
Push the right-hand side speed control lever forwards with your right thumb and the
scooter will move forward.
Push the left-hand side speed control lever forwards with your left thumb and the
scooter will move backward.
To brake, release the speed control lever which will return to neutral and activate the
electromagnetic brake automatically .This will bring the scooter to a prompt stop.
The speed control lever allows you to control the speed of the scooter up to a
maximum speed determined by the Speed Dial .The further the speed control lever is
deflected, the faster the scooter will go.
■Horn Button
Press the horn button to sound the horn. Release the button to stop the horn.
■Braking
Electro-magnetic brake: Release the speed control lever completely, and the
electromagnetic brake will be activated automatically, and the scooter will stop.
Slowest setting
Fastest setting

11
4 . O P E R AT I O N
Warning
When on a gradient NEVER set the vehicle to the freewheel mode. The electromagnetic
brakes will not be applied. This may result in injury or damage.
■Seat
The seat can be rotated and locked in position at 45 degrees intervals.
Push the seat adjustment lever forward and swivel the seat.
Release the lever, and then continue swiveling the seat until it locks in position.
Attention
Return the seat to the forward position before driving.
■Battery indicator
The battery indicator on the tiller console uses
a color code to indicate the approximate power
remaining in your batteries. Green indicates
(40~100%) capacity, yellow a draining charge(10～
30%),and red indicates that an immediate recharge
is necessary.
The remaining power suggested by the battery
indicator will vary by the actual driving time
incurred and how you drive. Repeated starting,
stopping, climbing will consume the power
more quickly.
■Main Circuit Breaker (Reset Button)
When the voltage in your scooter’s batteries becomes low or
the scooter is heavily strained because of excessive loads or
steep inclines, the main circuit breaker may tip to protect the
motor and electronics from damage.
♦The main circuit breaker rest button pops out when the
breaker trips.
♦When the breaker trips, the entire electrical system of your
scooter shuts down.
♦Allow a minute or two for your scooter’s electronics to “rest”.
♦Push in the reset button to reset the main circuit breaker.
RED
YELLOW
GREEN

12
4 . O P E R AT I O N
Suggestion
1. You should recharge the batteries after each time the vehicle is used to ensure maximum
range. The batteries should be charged up at least once a week even if the scooter is not
used.
2. After charging or replacing a new battery, drive the vehicle for 2-3 minutes to make sure
the battery capacity is sufficient.
3. In wintertime, the battery may respond more slowly and the battery range may be
reduced.
4. When driving on a gradient, the battery indicator light might move up and down. This is
a normal phenomenon so please do not worry.
5. Even if the battery is used properly, it is natural for the battery’s capacity to reduce with
time, which results in reduced battery range compared to a brand new battery. Therefore,
when you find the battery’s range is about only 50% of the range when the batteries were
new, it is time to replace the batteries. Please see your dealer about replacement
batteries. If you continue to use the old battery when it should be replaced, it could lead
to a rapid decline in performance.
6. The battery range will be reduced when driving frequently on a slope or rough terrain, as
this leads to greater consumption of power.
7. The batteries have a six-month warranty covering manufacturing defects. This warranty
does not cover faults due to incorrect battery recharging.
■How to adjust the seat height
1. Remove the seat from your scooter.
2. Remove the pin lock from the lower seat post.
3. Adjust the upper seat post to the desired seat height.
4. Move the upper seat post so that there is a hole to
insert the locking pin.
5. Insert the pin lock and replace seat replace seat.
Pin lock

13
4 . O P E R AT I O N
4.3 How to set to freewheel mode
Fig 4.1 Fig 4.2
◆Engaged mode (Fig. 4.1): Push the lever completely and the scooter can be driven by
motor power.
◆Freewheel Mode (Fig 4.2)：Pull the lever up and the scooter can be moved manually.
Warning
Never operate the freewheel lever while seated on the scooter or on an incline!
OPERATION OF THE FREEWHEEL LEVER
‧Always pull UP FIRMLY for freewheel mode
‧Always push DOWN FIRMLY for drive mode
Lever
Lever

14
■TillerAdjustment
The tiller can be adjusted in to many different positions to suit each driver.
1. Loosen the knob to adjust the tiller to positions you want. (Fig. 4.3)
2. Once decide the position, tighten the knob to secure the tiller.( Fig.4.4)
Fig. 4.3 Fig. 4.4
4 . O P E R AT I O N
Warning
♦Please hold the tiller before loosening the tiller adjustment knob.
♦Before lifting or driving the scooter make certain the tiller adjustment knob is fully
tightened.
♦Never attempt to adjust the tiller while the scooter is motion.
Adjustment
knob

15
5 . D R I V I N G O N T H E RO A D
■Starting and Driving
1. Make sure the seat is installed properly.
2. Make sure the tiller has been secured properly.
3. Fold down the armrests so you can rest your arms on them.
4. Turn the power switch to “ON”.
5. Check battery indicator to see whether there is enough power for your journey. If you
have any doubt about the remaining power, please recharge the batteries before
departure.
6. Set the speed dial to a position you feel safe and comfortable with.
7. Check the forward/reverse speed lever works correctly.
8. Make sure the electromagnetic brake works correctly.
9. Before driving, ensure it is safe to do in the environment around you.
Attention
1. Do not push both RH & LH sides of the speed control lever simultaneously. This might
leave you unable to control your scooter.
2. Do not turn the power switch to OFF while driving as this will lead to an emergency
stop and possible risk of accident and injury.
3. Do not set to the highest speeds whilst driving indoors.
4. Do not adjust the speed dial whilst driving, a sudden change in speed may cause danger
to you and others, and may cause damage to your scooter.
5. Do not place magnetic devices near the area of the operation handle as this could affect
the safe operation of your scooter. The scooter controller is located under the foot way.
6. Do be careful whilst driving in heavy traffic or crowded areas.
7. Whilst reversing the vehicle, beware of people or objects behind you.
Stopping
1. Release the speed control lever completely. The vehicle will naturally brake and stop.
2. Turn the power off. Then pull out the key.
Attention
1. The stopping distance will vary with your forward / reverse speed. Therefore please
begin braking as early as you can.
2. When parking your scooter, be sure to park on flat ground and then turn the power to
“OFF” before you dismount.

16
6. B AT T E R Y C H A R G I N G A N D C A R E
6.1 CHARGING THE BATTERY
■Method 1: On board Charging (see photograph overleaf)
Follow the procedure below step by step:
1. Turn the power switch to (OFF)
2. Plug the charger’s power cord into the mains.
3. Open the charging socket cap on the rear shroud. Then connect
the charger’s round plug to the charging socket.
4. Switch on the charger.
5. Both the charger’s red and orange LED will be lit when
6. Beginning charging. The charging duration is about 6 hours. To
ensure optimum performance a 10-hour charge is recommended.
7. Both the charger’s LED will be lit during the charging process.
The orange LED will turn green when charging is
complete.
8. Turn off the charger, disconnect the power cord and the round
plug from charger socket on the scooter.
■Method 2 Off-board Charging (see photograph overleaf)
1. Turn the power switch to (OFF)
2. Remove the battery pack by opening the battery
compartment and lifting out the battery pack by the handle.
3. Plug the charger’s power cord into the mains.
4. Plug the charger’s round plug into the charging socket of
the battery pack.
5. Switch on the charger.
6. Both the charger’s red and orange LED will be lit when
beginning charging. The charging duration is about 6 hours.
To ensure optimum performance a 10-hour charge is
recommended.
7. Both the charger’s LED will be lit during the charging process.
The orange LED will turn green when charging is complete.
8. Turn off the charger, disconnect the power cord and the round
plug from charger socket on the battery pack.
Attention
While returning the battery pack to the battery pack cavity of shroud, beware of finger
or hands.
Charger socket
Power Pack
Charger

17
6. B AT T E R Y C H A R G I N G A N D C A R E
■Charging Hours
The charging duration is about 6 hours. To ensure optimum performance a 10-hour
charge is recommended. But we do not recommend a charging more than 24 consecutive
hours.
■Batteries (Inside the Pack)
1. The PHOENIX HD 3/PHOENIX HD 4 is powered by two sealed lead-acid deep-cycle
batteries.
2. The batteries supplied with the scooter are 12 V 20ah batteries.
Warning
1. Keep away from flammable objects while charging as it may lead to fire or explosion of
battery.
2. Do not smoke while charging as the battery may release hydrogen gas. Always charge
your battery in a well-ventilated space.
3. Never connect or disconnect the plug or cord with wet hands while charging. Do not
connect or disconnect the plug or cord when they are wet, it may lead to electric shock.
Attention - Please follow the rules below to avoid accidents while charging.
1. Please use the WU’S charger only, and recharge the battery to its full capacity every
time. You may damage the battery and scooter if you use a charger, which is not to
the correct specification.
2. Please charge in a well-ventilated space where it is not directly exposed to the
sunlight. Do not charge in surroundings where it is humid or under rainfall and
morning dews.
3. Do not charge in temperatures less than -10°C or higher than +50°C as the charger
may not work well and the batteries may become damaged.
6.2 BATTERY
Do not expose the battery to temperatures below 10°C or above 50°C when charging
or storing the vehicle. Under the above temperature range can cause the battery either to
freeze or over heat. This will damage the batteries and shorten their life.
These batteries are maintenance free and there is no need to refill with water.
You are required to recharge the batteries on a regular basis. Even if the scooter is stood
idle, you should charge the batteries at least once a week.

18
6. B AT T E R Y C H A R G I N G A N D C A R E
The batteries carry a eight-month of manufacturer's warranty. This warranty only covers
issues relating to manufacturing faults, and not faults relating to failure to recharge the
batteries as instructed above.

Suggestion –How to maximize your batteries efficiency and service life
1. Fully recharge your new battery before its first time use.
2. Be sure to charge the battery fully every time. The battery life will be seriously
shortened or decayed if the battery is repeatedly used without being fully charged.
3. Always complete the charging until the orange LED light turns green. NEVER
stop charging before it is complete.
4. Keep your batteries fully charged whenever possible.
5. If you do not use your scooter for a long time, it should be charged at least every
week to keep the battery in a fully usable condition.
6. The ambient temperature will affect charging time. Charging time will be longer
in the winter.
7. After charging, do not leave the charger socket plugged in to the scooter, as this
will cause a power drain on the scooter and temporarily reduce its range.
■Cleaning the battery
If the batteries are contaminated by water, battery acid, dust or other substances, they
will discharge quickly. The batteries supplied with the scooter are sealed and as such
are maintenance free with no risk of battery leakage. Please follow the steps below to
clean the battery.
1. Turn the scooter power switch to OFF.
2. Follow the procedure in the next section “Replacing the Batteries”.
3. Use a clean cloth to wipe off the soiled area.
4. Take out the battery.
5. Clean the battery with a clean cloth. If the terminal is covered by white powder, please
wipe it clean using warm water.
6.3 REPLACING BATTERIES
■Batteries replacement
Follow the procedure below step by step to replace the batteries:
1. Turn the remove switch to unlock. Then remove the battery pack from the scooter.
2. Open the battery pack then disconnect the cables from the four battery terminals.
3. Remove the batteries from the battery pack.
4. Place new batteries inside the pack.
5. Connect the red cable to the positive (+) battery terminal and black cable to the
negative(-) on the other battery.
6. Connect up the fused cable between the two batteries and close the battery pack.

19
6. B AT T E R Y C H A R G I N G A N D C A R E
Warning
1. The wiring system and charger are well situated in the battery pack while being
assembled in plant. Do not attempt to re-locate the wiring system by yourself. The
improper layout of wiring system may result in the wires pinched by battery box,
which might result in the electronic system failure.
2. Be sure the battery wires are connected to their right battery terminal.
Suggestions
If necessary, ask for help from your dealer for advice about maintaining and replacing
the battery.
Suggestions
1. Make sure the terminals are installed properly and put the cover back on.
2. Do not use the battery to charge telecom equipment or other items.
3. Battery efficiency will vary with outside conditions; the driving distances will be
shorter in the winter. If the vehicle is not used for a long time, please charge the
battery at least every week.
4. Replace both batteries together.

20
7 . I N S P E C T I O N A N D M A I N T E N A N C E
7.1 INSPECTION
Clean the scooter with a damp cloth and dust down approximately once a week to
preserve the appearance of the scooter.
Adjust the tiller height and return to the original position and swivel the seat once a
week to ensure the parts adjust and remove smoothly and easily when required.
Check for signs of wear and tear on the tires and the upholstery on a regular basis.
For optimum performance and to increase the lifespan of your scooter, it is
recommended that you have your scooter serviced once a year.
7.2 REGULAR CHECKING RECORD
To make sure your scooter is correctly serviced, take it to your dealer for regular
maintenance checks. This should be at six months intervals after an initial inspection
after one month. Your dealer may charge a fee for this. The checking record is shown
overleaf.
YEAR
1
2
3
4
YEAR
1
2
3
4
Service Dates
Service Dates
Controller
Upholstery
On/off switch
Seat
Control Lever
Back
Braking
Armrests
Recharge point
Electrics
Batteries
Connections
condition
Levels
Harness
Connections
Test run
Discharge test
Forwards
Wheels and Tires
Reverse
Wear
Emergency stop
Pressure
Left turn
Bearings
Right turn
Wheel nuts
Slope test
Motors
Over obstacles
Wiring
List Items repaired
Noise
Connections
Brake
Brushes
Chassis
Condition
Steering