Dura Trel 11126 Installation guide

Model# 11126
6' Picnic Table with Benches
W221122-A5080
*W201121-A2040*
*W201121-A2040*
*W201121-A2040*
*W201121-A2040*
*W201121-A2040*
*W201121-A2040*
QUESTIONS? COMMENTS? CONTACT US!
115 Vision Parkway 1-877-258-6020
P.O. Box 122 www.dura-trel.com
Sheboygan Falls, WI 53085 [e-mail]
Assembly Instruction Manual
Please read instructions thoroughly before beginning assembly.
Check boxes carefully for contents listed. Some parts are packaged inside of others.
Assemble on a clean, flat, non-abrasive surface to prevent scratching.
In the event of missing or damaged parts please call or email our customer service department at
the contact info below.
Tools Required
-Battery or Electric Drill (#2 phillips bit, 1/4" & 3/32" drill bits)
-Tape Measure
-(2) 7/16" Wrenches or Sockets
-File
-All Purpose Grease (Optional)*
*In steps requiring nuts and bolts for assembly, we recommend placing a small
amount of grease on the end threads of the bolt. All hardware is stainless steel
and this practice will prevent galling or adhering together which may cause the
bolt to snap during assembly while using power tools.

28"
11"
72"
16"
29"
6' Picnic Table with Benches - Page 2

Lay out four 72" table top rails (part 1) and one center table rail (part 2) as shown above with pilot holes
facing up, leaving ⅛" gap between rails. Set four 12 ¾"" table brackets (part 3) over pilot holes at each
end of table top rail, making sure brackets are offset as shown. Using ¾" screws, fasten each bracket to
table top rails.
Apply glue to inner edges of ⅞ x 1½" end cap (from hardware bag) and press on each end of 27" cross
brace (part 5). Set center brace over pilot holes in center of table top. Using 1½" screws, fasten cross
brace to table top.
Apply glue to inside edges of 28" table top end cap (part 9). Press end cap onto ends of table top (DO
NOT slide from end). Take care that end cap is flush with ends of table and use a file to round off any
sharp edges.
1
2
3
6' Picnic Table with Benches - Page 3

Loosely bolt two table legs (part 14) together using 3½" bolts, washers and nylock nuts. Make sure pilot
holes for brackets are at the same end. Place each set of bolted legs into the bracket slots from step 1.
Line up pilot hole and fasten legs to table using 2 ¼" bolts, washer and nylock nuts.
Remove bottom nylock nut on one leg and slide bolt through the hole on angel brace (part 7). Replace
nut and tighten snugly. Repeat for opposite side. Overlap the two diagonal braces in the center of
table. Drill two 3/32" pilot holes through the diagonal braces and into center brace. Fasten with 1 ½"
screws to the center tabletop brace.
5
4
Apply glue to inside edges of four 7 ¼" (part 11) table leg end caps. Press end caps onto ends of table
legs (DO NOT slide from end). Take care that end cap is flush and use a file to round off any sharp
edges.
5
11
77
6' Picnic Table with Benches - Page 4

6
Lay out two of the 72" bench rails (part 13) as shown, leaving a 1/8” gap between rails. Set the two
bench brackets (part 4) over pilot holes and fasten brackets to bench rails using ¾” screws. Apply glue to
the 7/8 x 1 ½” molded end caps and push onto ends of center bench brace. Lay the brace over the pilot
holes in center of rails and fasten using 1.5” screws.
7
Apply glue to the 7/8 x 1 ½” molded end caps and push onto ends of center bench brace (part 6). Lay the
brace over the pilot holes in center of rails and fasten using 1 ½" screws.
6' Picnic Table with Benches - Page 5

8
Loosely bolt two bench legs (part 15) together using 4" bolts, washers and nylock nuts. Make sure pilot
holes for brackets are at the same end. Place each set of bolted legs into the bracket slots from step 8.
Line up pilot hole and fasten legs to bench using 4" bolts, washer and nylock nuts.
9
10
Remove bottom nylock nut on one leg and slide bolt through the hole on angel brace (part 8). Replace
nut and tighten snugly. Repeat for opposite side. Overlap the two angle braces in the center of table.
Drill two 3/32" pilot holes through the angle braces and into center brace. Fasten with 1 ½" screws to
the bench cross brace.
Apply glue to 11 ⅛" bench end caps (part 12). Press end caps onto ends of bench legs (DO NOT slide
from end). Take care that end cap is flush and use a file to round off any sharp edges.
8
6' Picnic Table with Benches - Page 6

Warranty Statement
20 Year Guarantee
Please call manufacturer direct with questions concerning missing or defective parts at Toll Free:
877-258-6020.
Dura-trel, Inc. products are warranted to be free from manufacturing defects resulting in delaminating,
peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the
PVC to change to its natural color for a period of 20 years from the date of purchase.
Normal weathering is defined as exposure to sunlight and extremes of weather and atmosphere which
will cause any colored surface to gradually fade.
CONDITIONS NOT COVERED BY THIS WARRANTY:
A. Physical abuse, misuse, neglect, or improper storage.
B. Improper installation or installation not in strict adherence to the instructions written by Dura-Trel,
Inc.
C. This warranty does not apply if materials are painted, varnished, or coated with any substance.
D. Dura-Trel, Inc. is not responsible for damages to product during shipping.
E. Damage attributable to atmospheric pollutants, hail, lightning, hurricane, tornado, wind borne
objects, earthquake, fire, mildew, casualty, act of God, building or ground settlement, or subjection to
stress or weight.
CLAIMS AND REMEDIES:
If a Dura-Trel, Inc. product is determined to have a manufacturing defect which is covered by this
warranty, Dura-Trel, Inc. will replace the material containing the defect (labor not included) F.O.B from
the point of manufacture. Dura-trel, Inc. will not be responsible for any cost incurred in the removal or
reinstallation of the product.
Important: All claims must be sent to the following address and should describe the defect claim.
Dura-Trel, Inc., P.O. Box 122, Sheboygan Falls, WI 53085
Dura-Trel, Inc. reserves the right to discontinue or change its design and/or color. If the original color
or style is not available, Dura-Trel, Inc. shall have the right to substitute a product designated by Dura-
Trel, Inc.
Dura-Trel, Inc. shall not be liable for any incidental, special, or consequential damages arising out of the
use of these products.
6' Picnic Table with Benches - Page 7