Dura Trel 11125 User manual

Model# 11125 Assembly Instructions
Part # Description
1
1½ x 5½ x 72" Seat Rail (with wood)
2 1½ x 5½ x 15¾" Leg
3 10¾" Seat Bracket
4⅞ x 1½ x 10 ⅛" Center Brace
5⅞ x 1½ x 24¾" Diagonal Brace
611 ⅛" Seat End Cap
7 6" Leg End Cap
8 Hardware Bag (includes:)
⅞ x 1½" End Cap
2" Painted Screw
¾" Painted Screw
¼ x 4" Bolt
¼" Nylock Nut
¼" Flat Washer
PLEASE READ THROUGH BEFORE BEGINNING ASSEMBLY. Super Glue Tube
IMPORTANT: Check boxes for Contents Listed
Check inside of parts as some parts are packaged
inside of others
In the event of missing, damaged or defective parts
please call our customer service dept. at 1-877-258-6020
When assembling components, place on a clean, flat
non-abrasive surface to avoid scratches
…
Battery or Electric Drill with #2 phillips bit, ⅛" drill bit
…Two 7/16" wrenches or sockets
…File
150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
www.dura-trel.com
[e-mail]
Tools Required
1-877-258-6020
1
6
General Information
6
6
16
16
1
2
2
4
1
2
4
2
Qty
2
6' Bench
1

150 Birch Road
P.O. Box 122
Sheboygan Falls, WI 53085
1-877-258-6020
2
www.dura-trel.com
[e-mail]
Please call manufacturer direct with questions concerning missing or defective parts at Toll Free:
877
-258-6020.
Dura
-trel,
Inc. products are warranted to be free from manufacturing defects resulting in delaminating,
peeling, flaking, corroding, cracking, crazing, or extreme amounts of fading or bleaching causing the
PVC to change to its natural color for a period of 20 years from the date of purchase.
Normal weathering is defined as exposure to sunlight and extremes of weather and atmosphere which
will cause any colored surface to gradually fade.
CONDITIONS NOT COVERED BY THIS WARRANTY:
A. Physical abuse, misuse, neglect, or improper storage.
B. Improper installation or installation not in strict adherence to the instructions written by Dura
-Trel,
Inc.
C. This warranty does not apply if materials are painted, varnished, or coated with any substance.
D. Dura
-Trel, Inc. is not responsible for damages to product during shipping.
E. Damage attributable to atmospheric pollutants, hail, lightning, hurricane, tornado, wind borne
objects, earthquake, fire, mildew, casualty, act of God, building or ground settlement, or subjection to
stress or weight.
CLAIMS AND REMEDIES:
If a Dura
-Trel, Inc. product is determined to have a manufacturing defect which is covered by this
warranty, Dura
-
Trel, Inc. will replace the material containing the defect (labor not included) F.O.B from
the point of manufacture. Dura
-trel, Inc. will not be responsible for any cost incurred in the removal or
reinstallation of the product.
Important:
An claims must be sent to the following address and should describe the defect claim.
Dura-Trel, Inc., P.O. Box 122, Sheboygan Falls, WI 53085
Dura
-Trel, Inc. reserves the right to discontinue or change its design, and or color. If the original color
or style is not available, Dura
-Trel, Inc. shall have the right to substitute a product designated by Dura-
Trel, Inc.
Dura
-Trel, Inc. shall not be liable for any incidental, special, or consequential damages arising out of
the use of these products
Warranty Statement
20 Year Guarantee

3
6' Bench
Lay out two 72" seat rails (part 1) with pilot holes facing up. Be sure wood inserts are flush with vinyl. Set two
10¾" seat brackets (part 3) over pilot holes at each end of seat rail, leaving ⅛" gap between rails. Using eight
¾" screws per bracket, fasten each bracket to seat rails.
Apply glue to inner edges of
⅞ x 1½" end cap (from hardware bag) and press on each end of 10⅛" center brace
(part 4). Set center brace over pilot holes in center of seat assembly. Using four 2" screws, fasten center brace
to seat assembly.

6' Bench
4
Insert one 15¾" leg (part 2) into bracket. Place second 15¾" leg (part 2) on inside of bracket and loosely fasten
with 4" bolts, washers and nuts. Set 24¾" diagonal brace on inside of legs with ¼" drilled hole against legs.
Using one 4" bolt, washers and nut, fasten diagonal brace to legs.
When inserting bolt, place TWO washers in
between legs.
Tighten all bolts.
Repeat for opposite end of bench.
In center of seat, overlap free ends of diagonal braces and drill two ⅛" holes through braces and into center
brace. Using two 2" screws, fasten both diagonal braces to center brace.
Apply
glue to inside edges of 11⅛" seat end cap (part 6). Press end cap onto ends of seat (DO NOT slide from
end). Take care that end cap is flush with ends of seat and use a file to round off any sharp edges.
Apply glue
to inside edges of 6" leg end cap (part 7). Press end cap onto bottoms of legs(DO NOT slide from end).

11125
6' Bench
1
1½ x 5½ x 72" Bench Rail 2.00
2
1½ x 5½ x 15¾" Bench Leg 4.00
3
10¾" Bench Bracket 2.00
4
⅞ x 1½ x 10 ⅛" Ctr Brace 1.00
5
⅞ x 1½ x 24¾" Bench Diago 2.00
6
11 ⅛" End Cap 2.00
7
6" Bench Leg End Cap 4.00
8
Hardware Bag 1.00
⅞ x 1½" End Cap 2.00
2" Painted Screw 6.00
¾" Painted Screw 16.00
¼ x 4" Bolt 6.00
¼" Nylock Nut 6.00
¼" Flat Washer 16.00
PVC Glue 1.00