Dura Trel 11136 User manual

TOOLS NEEDED:
Drill with #2 Phillips Bit or
Phillips Screwdriver
7/16” Wrenches or Sockets
File
#11136 PARK/PIER BENCH
ASSEMBLY INSTRUCTIONS
BENCH SEAT ASSEMBLY
(Refer to Upper portion of Drawing 1)
On a flat non-abrasive surface lay out the three 1 ½ x 5 ½ x 60” seat rails with screw pilot holes facing
upwards (seat rails will have pilot holes in the center of the rails for center brace). Place the two seat
brackets on rails as shown; fasten brackets to rails using ¾” screws. Apply glue to the inside edges of the
two 7/8 x 1 ½" molded end caps on the push onto the ends of the seat brace. Lay the center brace over
pilot holes in center of seat rails and fasten with 2” screws. Apply glue to the inside edges of the two
7/8 x 1 ½ x 16 ¾" seat end caps and push them onto the ends of the seat assembly making sure the edges
are flush. (Note: do not slide caps from ends.) Set aside.
BENCH BACK ASSEMBLY
(Refer to Lower portion of Drawing 1) (Make 2)
Lay one of the 1 ½ x 5 ½ x 60” bench back rails with screw pilot holes facing up. Lay two of the 4” brackets
over the pilot holes and fasten with ¾” screws. Apply glue to the 7/8 x 1 ½ x 5 ½" end caps and push one
on each end of the rail. Set aside.
BENCH LEGS AND SUPPORT ASSEMBLY
(Refer to Drawing 2)
Apply glue to the inside edges of the 1 ½ x 5 5/8" angled end caps and push onto the front angled end of the
22" bench supports; do the same with the 1 ½ x 5 ½" end caps and push them onto the back ends of the
bench supports.
Lay out one of the1 ½ x 5 ½ x 22” bench supports; with angled end toward the front. Place one of the 1 ½
x 5 ½ x 18” front leg pieces on top of the bench support with the angled end and place one of the 1 ½ x 5 ½
x 34" back legs on the straight end of the bench support. Line up the bolt holes and fasten with the 3 ½”
bolts, washers and nylock nut as shown. Bolt heads should be on the side of the bench support that does not
have the legs. (Note: Draw bolts up snug, but do not over tighten.)
For opposite side; place the legs on the opposite side of the bench support. Fasten with 3 ½” bolts.
Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
SEAT ATTACHMENT
(Refer to Drawing 3)
Lay the bench seat assembly from Drawing 1on the edge of a table or workbench. Place the bench
leg/support assemblies into the brackets as shown (make sure the bench support pieces face the outside of
completed bench). Fasten each side with 2 ¼” bolts, washers and nylock nuts (bolt head should face the
outside of the completed bench).
Apply glue to the end caps for the bottom of legs, using the 5 5/8” angled end caps for front legs and 5 ½”
end caps for back legs. (Note: If the Bench is being attached to a Pier or Deck with Bench
Anchor Kit, DO NOT apply End Caps to bottoms of legs.)
SEAT BACK ATTACHMENT
(Refer to Drawing 4)
Please pay close attention to order of placement.
Using one of the seat back assemblies from Drawing 1, slide the brackets over the lower part of the bench
back legs. Line up the bolt holes and fasten using 2 ¼" bolts, washers and nylock nuts. Apply glue to two of
the 7/8 x 1 ½ x 4" end caps and place above the lower seat rail. Make sure the end caps are tight against the
brackets of the lower seat back assembly. Place the second seat back assembly above the ends, line up bolt
holes and fasten as above. Apply glue carefully to the 3/8 x 1 ½ x 2" end caps from hardware bag and place
on top of the back legs.
*Upon completion of bench be sure to file or sand any
sharp edges on the end caps to prevent cuts and scrapes.*
If you encounter missing or defective parts, please contact manufacturer direct at toll free #
below.

Dura-Trel, Inc. ~ PO Box 122, Sheboygan Falls, WI 53085 ~ Toll Free 877-258-6020
PACKING LIST
PARTS CONTAINED:
#11136 park/pier bench
QTY. PART NO. PART DESCRIPTION
3 41555-60001 1½ x 5½ x 60” SEAT RAIL
2 41555-60002 1½ x 5½ x 60” BACK RAIL
2 41555-34001 1½ x 5½ x 34” ANGLED BACK LEG
2 41555-16000 1½ x 5½ x 16” FRONT LEG
2 41555-22500 1½ x 5½ x 22½" BENCH SUPPORT
1 4TBCK-14500L 14½” LEFT BRACKET
1 4TBCK-14500R 14½” RIGHT BRACKET
4 4TBCK-04000 4” SEAT BACK BRACKET
1 47815-15750
⅞x 1½ x 15¾" SEAT BRACE
2 5ECAP-16750
⅞x 1½ x 16¾" SEAT END CAP
4 5ECAP-05580
⅞x 1½ x 5⅝” ANGLED END CAP
8 5ECAP-05500
⅞x 1½ x 5½" END CAP
1 7GLUE-4OZCN 4 oz PVC GLUE CAN
Hardware Bag Includes:
4 5ECAP-04000
⅞x 1½ x 4” SEAT BACK END CAP
2 5ECAP-02000
⅜x 1 ½ x 2” TOP SEAT BACK END CAP
2 5ECAP-7815E
⅞x 1 ½" END CAPS
40 7HDWR-06034 ¾” SCREW
6 7HDWR-06200 2" SCREW
8 7HDWR-14350 ¼ x 3 ½" BOLT
8 7HDWR-14225 ¼ x 2 ¼” BOLT
16 7HDWR-14NUT ¼” NYLOCK NUT
32 7HDWR-14WSH ¼” FLAT WASHER
1 PARK/PIER BENCH INSTRUCTIONS
NOTE: Some parts may be packed inside of others.
If you encounter missing or defective parts, please contact manufacturer direct at toll free # below.