Dynojet POWER COMMANDER III User manual

2007 Ducati 1098 - PCIII USB - 1 


Dynojet Research 2191 Mendenhall Drive North Las Vegas, NV 89081 [phone] www.powercommander.com

1 PowerCommander
1 USBCable
1 CD-ROM
1 InstallationGuide
1 PowerAdapter
1 WireTap
2 PowerCommanderDecals
2 DynojetDecals
2 Velcro®Strip
1 AlcoholSwab
4 Zipties
YoucanalsodownloadthePower
Commandersoftwareandlatestmaps
fromourwebsiteat:




Button Adjustment Display
Faceplate Buttons
Expansion Port USB Port

5. Lay the PCIII in the tail section
temporarily.
6 Route the PCIII harness through the
hole in the tail section (Fig. C).
7. Route the PCIII along the right hand
side of the subframe . Secure the
PCIII harness to the subframe using 2
of the large supplied zip ties (Fig. D)
Fig. B Fig. AFig. CFig. D
2007 Ducati 1098 - PCIII USB - 2 
Zip ties
PCIII harness
1. Remove the seat and solo cover.
2. Remove the cover around the fuel tank
(Fig. A).
3 Remove the fuel tank
4. Remove the inner fairing cover on the
right hand side (Fig. B).

8 Unplug the stock wiring harness from the
rear injector (Fig. E)
This injector is located on top of the air
box.
To remove the connector you must first
remove the spring clip. This is best done
with a pick or small screwdriver.
9 Plug the YELLOW colored wires from the
PCIII in-line of the stock wiring harness
and rear injector (Fig. F).
Make sure to reinstall the spring clip on
the stock connector.
10 Use 1 of the small supplied zip ties to
secure this connection to the fuel line.
Make this connection as compact as
possible.
11 Unplug the stock wiring harness from the
front injector (Fig G).
This connection is very difficult to access.
It is best to get to thru the front of the bike
directly above the radiator.
Figure G was taken from the front of the
bike inside the right hand fairing and
above the radiator.
Fig. EFig. FFig G
2007 Ducati 1098 - PCIII USB - 3 
Unplug
PCIII connector Stock connector
Zip tie
Stock connector

14 Route the PCIII harness along the right
hand side frame down tube. Use the
existing wraps to hold the PCIII harness in
place (Fig. J).
15 Locate the Throttle
Position Sensor
on the right hand
side of the throttle
bodies.
17 Connect the GREY
wire from the PCIII
to the Posi-Tap.
12 Plug the ORANGE colored wires from the
PCIII in-line of the front injector and stock
wiring harness (Fig. H).
13 Remove the right hand fairing.
Fig. H
2007 Ducati 1098 - PCIII USB - 4 
PCIII connector Stock connector
Fig. J
18 Attach the ground wire from the PCIII to
the right hand engine cover bolt shown in
Figure K
19 Reinstall the right hand fairing
Ground wire
from PCIII
Fig. K
TPS
PCIII harness
Grey wire/Posi-Tap

Fig. L
2007 Ducati 1098 - PCIII USB - 5 
20 Install the PCIII in the tail section using the
supplied velcro. Make sure to clean both
surfaces with the alcohol swab before
attaching.
21 Reinstall all bodywork and fuel tank.
When lowering the fuel tank make sure it
does not interfere with the connection of
the rear injector.
Note: Unless you have the Kit ECU you
will not be able to make fuel changes
below 20% throttle and below 5500rpm
with this PCIII.