Dynojet POWER COMMANDER FC User manual

2008-2010 Kawasaki ZX-10R - 1IFC17004.01 www.powercommander.com
Installation Instructions
PLEASE READ ALL DIRECTIONS BEFORE STARTING INSTALLATION
THE IGNITION MUST BE TURNED
OFF BEFORE INSTALLATION!
YOU CAN ALSO DOWNLOAD THE PCFC
CONTROL CENTER SOFTWARE AND
LATEST MAPS FROM OUR WEB SITE AT:
www.powercommander.com
2191 Mendenhall Drive North Las Vegas, NV 89081 [phone] www.powercommander.com
1 Power Commander FC
1 USB Cable
1 Installation Guide
2 Dynojet Decals
2 Velcro
1 Alcohol swab
2008-2010 Kawasaki ZX-10R
2008-2010 Kawasaki ZX-10R
Parts List
Parts List

IFC17004.01 www.powercommander.com 2008-2010 Kawasaki ZX-10R - 2
USB Port
HIGH RPM Dial
MID RPM Dial
LOW RPM Dial
MAP Select
STATUS Light
Position Note
Position 1
2008-2010 Kawasaki ZX-10R
Stock exhaust
Stock or aftermarket air filter
SELECTING THE MAP POSITION
The Dynojet Power Commander Fuel Controller (PCFC) comes loaded with up to ten
maps. Using a #1 Phillips screwdriver, turn the map select dial to toggle between the
loaded maps. Refer to the map position table for the maps included in your PCFC.
USING THE RPM RANGE DIALS
The Low, Mid, and High RPM Dials refer to the RPM range, in thirds, of your vehicle.
Each dial allows +/- 10% fuel adjustment on top of what fuel changes are done in the
map. With the dial facing straight up, there is no additional fuel change.
For example, if your vehicle revs to 6000 RPM:
• The low RPM dial will adjust 0-2000 RPM
• The mid RPM dial will adjust 2001-4000 RPM
• The high RPM dial will adjust 4001-6000 RPM
USING PCFC CONTROL CENTER
Take your tuning to the next level with the PCFC Control Center software.
1 Using your web browser, navigate to www.powercommander.com.
2 Click Enter Race Ready.
3 Click Downloads.
4 Click Access Downloads for Power Commander FC.
5 Click the PCFC software Download button.
6 Open the zip folder.
7 Double-click the install file and follow the on-screen instructions to install the PCFC
Control Center software. The PCFC Control Center software and maps will be
stored in C:\Program Files\PCFC Control Center.
8 Return to the Downloads or Home page where you can enter the make, model, and
year of your bike to check for and download additional maps.
LOADING ADDITIONAL MAPS
1 Connect the USB cable from the computer to the PCFC. Verify the cable is fully
seated in the PCFC.
2 Run the Control Center software by double-clicking the program icon installed on
your desktop or on your start menu.
3 Click Open Map File and select a map file.
4 Click Send Map. You can send the map to any of the ten map positions.
ALTERING MAPS USING SOFTWARE
The values in the map represent a percentage of fuel change over stock. A value of 10 in
the map indicates at that throttle position and RPM range the vehicle will be 10% richer
than stock. If the value is -10, then it would be 10% leaner than stock. You have the
ability to fine tune your fuel curve by altering these values. The Control Center software
allows a value of +250 to -100 in each cell.

IFC17004.01 www.powercommander.com 2008-2010 Kawasaki ZX-10R - 3
1 Remove the main seat and the passenger seat.
2 Remove the covers for each side of the fuel tank as shown in Figure A.
3 Prop the front of the fuel tank up.
4 Slide the junction box that is under the main seat from it’s rubber sleeve.
This allows room for the PCFC harness.
5 Route the PCFC harness underneath the sub frame crossover as shown in
Figure B.
6 Unplug the stock wiring harness from the throttle bodies as shown in Figure C.
This is a 16-pin brown connector located under the fuel tank on the right hand
side of the bike.
FIG.A
FIG.C
FIG.B

IFC17004.01 www.powercommander.com 2008-2010 Kawasaki ZX-10R - 4
7 Attach the connectors from the PCFC to the stock wiring harness and throttle
body harness as shown in Figure D.
8 Attach the ground wire from the PCFC harness to the stock wiring harness
chassis ground as shown in Figure E.
This connection is next to the PCFC connection and starter relay.
9 Using the supplied velcro, secure the PCFC in the tail section as shown in
Figure F.
Make sure to clean both surfaces with the alcohol swab before attaching.
10 Reinstall the fuel tank and covers.
11 Reinstall the passenger and main seats.
FIG.D
FIG.E
FIG.F