Endress+Hauser Liquistation CSF34 User manual

Products Solutions Services
Operating Instructions
Liquistation CSF34
Automatic sampler for liquid media
BA00478C/07/EN/11.22-00
71588428
2022-09-16
Valid as of version
01.12.01

Liquistation CSF34 Table of contents
Endress+Hauser 3
Table of contents
1 About this document ................ 5
1.1 Warnings ............................ 5
1.2 Symbols .............................. 5
1.3 Symbols on the device ................... 5
1.4 Documentation ........................ 6
2 Basic safety instructions ............ 7
2.1 Requirements for the personnel ............ 7
2.2 Intended use .......................... 7
2.3 Workplace safety ....................... 7
2.4 Operational safety ...................... 8
2.5 Product safety ......................... 9
3 Product description ................ 10
3.1 Product design ........................ 10
3.2 Equipment architecture ................. 11
3.3 Terminal diagram ..................... 12
4 Incoming acceptance and product
identification ..................... 13
4.1 Incoming acceptance ................... 13
4.2 Product identification ................... 13
4.3 Storage and transport .................. 14
4.4 Scope of delivery ...................... 14
5 Mounting ......................... 15
5.1 Mounting requirements ................. 15
5.2 Setting up the device ................... 19
5.3 Sampling with a flow assembly ............ 21
5.4 Post-installation check .................. 22
6 Electrical connection .............. 23
6.1 Connecting the sensors ................. 23
6.2 Connecting the sampler controller ......... 27
6.3 Connecting the signal transmitter to the
alarm relay .......................... 30
6.4 Connecting the communication ........... 31
6.5 Connecting additional inputs, outputs or
relays .............................. 37
6.6 Connecting the supply voltage ............ 39
6.7 Special connection instructions ............ 42
6.8 Hardware settings ..................... 42
6.9 Ensuring the degree of protection .......... 43
6.10 Post-connection check .................. 44
7 Operation options ................. 45
7.1 Overview of operation options ............ 45
7.2 Structure and function of the operating
menu .............................. 45
7.3 Access to the operating menu via the local
display ............................. 47
8 System integration ................ 50
8.1 Integrating the sampler in the system ....... 50
9 Commissioning .................... 54
9.1 Function check ....................... 54
9.2 Setting the operating language ............ 54
9.3 Configuring the measuring device .......... 54
10 Operation ......................... 59
10.1 Display ............................. 59
10.2 General settings ....................... 61
10.3 Programming ........................ 77
10.4 Inputs ............................. 112
10.5 Outputs ............................ 117
10.6 Additional functions .................. 126
11 Diagnostics and troubleshooting .. 146
11.1 General troubleshooting ................ 146
11.2 Diagnostic information on local display ..... 147
11.3 Diagnostic information via web browser .... 147
11.4 Diagnostic information via fieldbus ........ 147
11.5 Adapting the diagnostic information ...... 148
11.6 Overview of diagnostic information ....... 150
11.7 Pending diagnostic messages ............ 159
11.8 Diagnostics list ...................... 159
11.9 Event logbook ....................... 159
11.10 Device information ................... 165
11.11 Resetting the device ................... 172
11.12 Firmware history ..................... 173
12 Maintenance .................... 176
12.1 Maintenance tasks .................... 176
13 Repair ........................... 188
13.1 Spare parts ......................... 188
13.2 Return ............................. 188
13.3 Disposal ........................... 188
14 Accessories ...................... 189
14.1 Device-specific accessories .............. 189
14.2 System components ................... 192
15 Technical data ................... 196
15.1 Input .............................. 196
15.2 Output ............................ 197
15.3 Protocol-specific data .................. 201
15.4 Power supply ........................ 202
15.5 Performance characteristics ............. 203
15.6 Environment ........................ 204
15.7 Process ............................ 204
15.8 Mechanical construction ............... 205

Table of contents Liquistation CSF34
4 Endress+Hauser
Index ................................. 207

Liquistation CSF34 About this document
Endress+Hauser 5
1 About this document
1.1 Warnings
Structure of information Meaning
LDANGER
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation will result in a fatal or serious
injury.
LWARNING
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid the dangerous situation can result in a fatal or serious
injury.
LCAUTION
Causes (/consequences)
If necessary, Consequences of
non-compliance (if applicable)
‣Corrective action
This symbol alerts you to a dangerous situation.
Failure to avoid this situation can result in minor or more serious injuries.
NOTICE
Cause/situation
If necessary, Consequences of
non-compliance (if applicable)
‣Action/note
This symbol alerts you to situations which may result in damage to
property.
1.2 Symbols
Additional information, tips
Permitted
Recommended
Forbidden or not recommended
Reference to device documentation
Reference to page
Reference to graphic
 Result of a step
1.3 Symbols on the device
Reference to device documentation
Do not dispose of products bearing this marking as unsorted municipal waste. Instead, return them
to the manufacturer for disposal under the applicable conditions.

About this document Liquistation CSF34
6 Endress+Hauser
1.4 Documentation
The following manuals complement these Operating Instructions and are available on the
product pages on the Internet:
• Brief Operating Instructions Liquistation CSF34, KA01169C
• Operating Instructions for Memosens, BA01245C
• Software description for Memosens inputs
• Calibration of Memosens sensors
• Sensor-specific diagnostics and troubleshooting
• Operating Instructions for HART communication, BA00486C
• Onsite settings and installation instructions for HART
• Description of HART driver
• Guidelines for communication via fieldbus and web server
• HART, SD01187C
• PROFIBUS, SD01188C
• Modbus, SD01189C
• Web server, SD01190C
• Web server (optional), SD01190C
• EtherNet/IP, SD01293C
• Special Documentation: Sampler application manual SD01068C
• Documentation on other devices in the Liquiline platform:
• Liquiline CM44xR (DIN rail device)
• Liquiline System CA80 (analyzer)
• Liquiline System CAT8x0 (sample preparation)
• Liquistation CSFxx (sampler)
• Liquiport CSP44 (sampler)

Liquistation CSF34 Basic safety instructions
Endress+Hauser 7
2 Basic safety instructions
2.1 Requirements for the personnel
• Installation, commissioning, operation and maintenance of the measuring system may
be carried out only by specially trained technical personnel.
• The technical personnel must be authorized by the plant operator to carry out the
specified activities.
• The electrical connection may be performed only by an electrical technician.
• The technical personnel must have read and understood these Operating Instructions
and must follow the instructions contained therein.
• Faults at the measuring point may only be rectified by authorized and specially trained
personnel.
Repairs not described in the Operating Instructions provided must be carried out only
directly at the manufacturer's site or by the service organization.
2.2 Intended use
Liquistation CSF34 is a stationary sampler for liquid media. The samples are taken
discontinuously using a vacuum pump or peristaltic pump and are then distributed into
sampling containers and refrigerated.
The sampler is designed for use in the following applications:
• Communal and industrial wastewater treatment plants
• Laboratories and water management offices
• Monitoring of liquid media in industrial processes
Use of the device for any purpose other than that described poses a threat to the safety of
people and of the entire measuring system, and is therefore not permitted. The
manufacturer is not liable for damage caused by improper or non-intended use.
2.3 Workplace safety
As the user, you are responsible for complying with the following safety conditions:
• Installation guidelines
• Local standards and regulations
• Regulations for explosion protection
Electromagnetic compatibility
• The product has been tested for electromagnetic compatibility in accordance with the
applicable international standards for industrial applications.
• The electromagnetic compatibility indicated applies only to a product that has been
connected in accordance with these Operating Instructions.

Basic safety instructions Liquistation CSF34
8 Endress+Hauser
2.4 Operational safety
Before commissioning the entire measuring point:
1. Verify that all connections are correct.
2. Ensure that electrical cables and hose connections are undamaged.
3. Do not operate damaged products, and protect them against unintentional operation.
4. Label damaged products as defective.
During operation:
‣If faults cannot be rectified:
products must be taken out of service and protected against unintentional operation.
LCAUTION
Programs not switched off during maintenance activities.
Risk of injury due to medium or cleaning agent!
‣Quit any programs that are active.
‣Switch to the service mode.
‣If testing the cleaning function while cleaning is in progress, wear protective clothing,
goggles and gloves or take other suitable measures to protect yourself.

Liquistation CSF34 Basic safety instructions
Endress+Hauser 9
2.5 Product safety
2.5.1 State-of-the-art technology
The product is designed to meet state-of-the-art safety requirements, has been tested, and
left the factory in a condition in which it is safe to operate. The relevant regulations and
international standards have been observed.
Devices connected to the sampler must comply with the applicable safety standards.
2.5.2 IT security
We only provide a warranty if the device is installed and used as described in the
Operating Instructions. The device is equipped with security mechanisms to protect it
against any inadvertent changes to the device settings.
IT security measures in line with operators' security standards and designed to provide
additional protection for the device and device data transfer must be implemented by the
operators themselves.

Product description Liquistation CSF34
10 Endress+Hauser
3 Product description
3.1 Product design
A complete sampling unit comprises:
• Controller with display, soft keys and navigator
• Vacuum or peristaltic pump for sampling
• PE or glass sample bottles for sample preservation
• Sampling chamber temperature regulator (optional) for safe sample storage
• Suction line with suction head
12
3
4
5
6
7
9
8
10
A0029715
 1 Example of a Liquistation, version with vacuum pump
1 Controller
2 Window (optional)
3 Dosing compartment door
4 Suction line connection
5 Sampling chamber door
6 Sample bottles, e.g. 2 x 12
bottles, PE, 1 liter
7 Bottle trays (depending on
sample bottles selected)
8 Distribution plate (depending
on sample bottles selected)
9 Distribution arm
10 Vacuum system, e.g. Dosing
system with conductive
sample sensor
12
3
4
5
6
7
9
8
10
A0024291
 2 Example of a Liquistation, version with peristaltic pump
1 Controller
2 Window (optional)
3 Dosing compartment door
4 Suction line connection
5 Sampling chamber door
6 Sample bottles, e.g. 2 x 12
bottles, PE, 1 liter
7 Bottle trays (depending on
sample bottles selected)
8 Distribution plate (depending
on sample bottles selected)
9 Distribution arm
10 Peristaltic pump

Liquistation CSF34 Product description
Endress+Hauser 11
3.2 Equipment architecture
3.2.1 Slot and port assignment
E
85
85 86
86
41
43 42
87
88
97
98
31
31 32
32
SD
Display
1
2
Sensor
0/4 ... 20 mA
Sensor supply
+
+
–
+
+
–
1
2
Service
PK
GY
PK
GYGY
1
2
–
BN
WH
GN
YE
BN
WH
GN
YE
87
88
97
98
+
–AB
+
–
A
B
–
Alarm
HART
Power
(internal)
24VDC
24V
12,5V
3,3V
A0045689
 3 Slot and port assignment of hardware and presentation on the display
The electronics configuration follows a modular concept:
• There are several slots for electronics modules. These are referred to as "slots".
• These slots are numbered consecutively in the housing. Slots 0 and 1 are always reserved
for the base module.
• In addition there are also inputs and outputs for the control module. These slots are
labeled "S".
• Each electronics module has one or more inputs and outputs or relays. Here they are all
collectively known as "ports".
• Ports are consecutively numbered per electronics module and are recognized
automatically by the software.
• Outputs and relays are named according to their function, e.g. "current output", and are
displayed in ascending order with the slot and port numbers.
Example:
"Current output 2:1" shown on the display means: slot 2 (e.g. AOR module) : port 1
(current output 1 of the AOR module)
• Inputs are assigned to measuring channels in the ascending order of "slot:port number"
Example:
"CH1: 1:1" shown on the display means:
Slot 1 (base module) : port 1 (input 1) is channel 1 (CH1).

Product description Liquistation CSF34
12 Endress+Hauser
3.3 Terminal diagram
The unique terminal name is derived from:
Slot no. : Port no. : Terminal
Example, NO contact of a relay
Device with inputs for digital sensors, 4 current outputs and 4 relays
• Base module BASE2-E (contains 2 sensor inputs, 2 current outputs)
• 2AO module (2 current outputs)
• 4R module (4 relays)
1 2 34
43 42 41
Relay 1
Relay 2
Relay 3
Relay 4
Slot
Slot 4 Port 1 Pin 41
BASE2-E 2DS 4R 2AO
43 42 41 43 42 41
43 42 41
43 42 41
A0039621
 4 Creating a terminal diagram using the example of the NO contact (terminal 41) of a relay

Liquistation CSF34 Incoming acceptance and product identification
Endress+Hauser 13
4 Incoming acceptance and product
identification
4.1 Incoming acceptance
1. Verify that the packaging is undamaged.
 Notify the supplier of any damage to the packaging.
Keep the damaged packaging until the issue has been resolved.
2. Verify that the contents are undamaged.
 Notify the supplier of any damage to the delivery contents.
Keep the damaged goods until the issue has been resolved.
3. Check that the delivery is complete and nothing is missing.
 Compare the shipping documents with your order.
4. Pack the product for storage and transportation in such a way that it is protected
against impact and moisture.
 The original packaging offers the best protection.
Make sure to comply with the permitted ambient conditions.
If you have any questions, please contact your supplier or your local Sales Center.
4.2 Product identification
Nameplates can be found:
• On the inside of the door
• On the packaging (adhesive label, portrait format)
4.2.1 Nameplate
The nameplate provides you with the following information on your device:
• Manufacturer identification
• Order code
• Extended order code
• Serial number
• Firmware version
• Ambient and process conditions
• Input and output values
• Activation codes
• Safety information and warnings
• Certificate information
‣Compare the information on the nameplate with the order.
4.2.2 Product identification
Product page
www.endress.com/CSF34
Interpreting the order code
The order code and serial number of your product can be found in the following locations:
• On the nameplate
• In the delivery papers

Incoming acceptance and product identification Liquistation CSF34
14 Endress+Hauser
Obtaining information on the product
1. Go to www.endress.com.
2. Page search (magnifying glass symbol): Enter valid serial number.
3. Search (magnifying glass).
 The product structure is displayed in a popup window.
4. Click the product overview.
 A new window opens. Here you fill information pertaining to your device,
including the product documentation.
4.2.3 Manufacturer address
Endress+Hauser Conducta GmbH+Co. KG
Dieselstraße 24
D-70839 Gerlingen
4.3 Storage and transport
NOTICE
Damage to the sampler
If transported incorrectly, the roof may become damaged or tear off.
‣Transport the sampler using a lifting truck or forklift. Do not lift the sampler by the
roof. Lift it in the middle between the top and bottom sections.
4.4 Scope of delivery
The scope of delivery comprises:
• 1 Liquistation CSF34 with:
• The ordered bottle configuration
• Optional hardware
• Accessories kit
For peristaltic or vacuum pump:
Hose adapter for suction line with various angles (straight, 90°), Allen screw (for version
with vacuum pump only)
• 1 printed copy of the Brief Operating Instructions in the language ordered
• Optional accessories
‣If you have any queries:
Please contact your supplier or local sales center.

Liquistation CSF34 Mounting
Endress+Hauser 15
5 Mounting
5.1 Mounting requirements
5.1.1 Dimensions
355 (14.0)
125 (4.9)
903 (35.6)
1258 (49.5)
625 (24.6)
471 (18.5)
816 (32.1)
753 (29.7)
355 (14.0)
125 (4.9)
530 (20.9)
1403 (55.2)
1758 (69.2)
625 (24.6)
471 (18.5)
816 (32.1)
753 (29.7)
AA
A
A
A0025857
 5 Dimensions of Liquistation, plastic version, without/with stand. Unit of measurement mm (in)
A Suction line connection

Mounting Liquistation CSF34
16 Endress+Hauser
355 (14.0)
125 (4.9)
903 (35.6)
1297 (51.1)
624 (24.6)
467 (18.4)
816 (32.1)
743 (29.3)
355 (14.0)
125 (4.9)
530 (20.9)
1403 (55.2)
1797 (70.8)
624 (24.6)
467 (18.4)
816 (32.1)
743 (29.3)
A
A
AA
A0024423
 6 Dimensions of Liquistation, stainless steel version, without/with stand. Unit of measurement mm (in)
A Suction line connection

Liquistation CSF34 Mounting
Endress+Hauser 17
5.1.2 Installation site
For version with sample pump
1 2 3
4
A0024411
 7 Liquistation mounting conditions
Mounting conditions
Route the suction line with a downward gradient to the sampling point.
Never mount the sampler in a place where it is exposed to aggressive gases.
Avoid siphoning effects in the suction line.
Do not route the suction line with an upward gradient to the sampling point.
Note the following when erecting the device:
• Erect the device on a level surface.
• Connect the device securely to the surface at the fastening points.
• Protect the device against additional heating (e.g. heaters or direct sunlight).
• Protect the device against mechanical vibrations.
• Protect the device against strong magnetic fields.
• Make sure air can circulate freely at the side panels of the cabinet. Do not mount the
device directly against a wall. Allow at least 150 mm (5.9 in.) from the wall to the left
and right.
• Do not erect the device directly above the inlet channel of a wastewater treatment plant.

Mounting Liquistation CSF34
18 Endress+Hauser
5.1.3 Mechanical connection
Foundation plan
302 (11.9)
195.4 (7.69)
C
C
D
B
AA
AA
137.4 (5.41) 355 (14.0) 61 (2.4)
605 (23.8)
730 (28.7)
786 (30.9)
214 (8.43)
255 (10.0)
311 (12.2) 305 (12.0)
33.6 (1.32)
A0024406
 8 Foundation plan. Unit of measurement mm (in)
A Fasteners (4 x M10)
B Cable inlet
C Outlet for condensate and overflow > DN 50
D Sample supply from below > DN 80
--- Dimensions of Liquistation
5.1.4 Connection for sample intake and for version with sample
pump
• Maximum suction height:
• Vacuum pump: option 8 m (26 ft)
• Peristaltic pump: standard 8 m (26 ft)
• Maximum hose length: 30 m (98 ft)
• Hose connection diameter
• Vacuum pump: 10 mm (3/8 in) 13 mm (1/2 in) , 16 mm (5/8 in) or 19 mm (3/4 in)
internal diameter
• Peristaltic pump: 10 mm (3/8 in) internal diameter
• Intake speed:
> 0.6 m/s (> 1.9 ft/s) for 10 mm (3/8 in) ID, as per Ö 5893, US EPA
> 0.6 m/s (> 1.9 ft/s) for ≤ 13 mm (1/2") ID, as per EN 25667, ISO 5667
> 0.5 m/s (> 1.6 ft/s) for ≤ 13 mm (1/2") ID, in accordance with EN 25667, ISO 5667
Note the following when erecting the device:
• Always lay the suction line so that it slopes upwards from the sampling point to the
sampler.
• The sampler must be located above the sampling point.
• Avoid siphoning effects in the suction line.

Liquistation CSF34 Mounting
Endress+Hauser 19
Requirements for the sampling point:
• Do not connect the suction line to pressurized systems.
• Use the suction filter to impede coarse and abrasive solids and solids which can cause
clogging.
• Immerse the suction line in the direction of flow.
• Take the sample at a representative point (turbulent flow, not directly at the bottom of
the channel).
Useful sampling accessories
Suction filter:
Impedes coarser solids and solids which can cause clogging.
5.2 Setting up the device
5.2.1 Connecting the suction line at the side on version with pump
1. When setting up the device, take the installation conditions into account.
2. Route the suction line from the sampling point to the device.
3. Fit a hose adapter on the hose.
4. Secure the hose adapter with a worm drive hose clip.
5. Screw the suction line onto the device's hose connection.
5.2.2 Connecting the suction line from below on version with pump
If the suction line is connected from below, the suction line is routed upwards behind the
rear panel of the sample compartment.
1. Remove the rear panel of the dosing compartment and sample compartment
beforehand.
2. Remove the drain plug from the hose gland located at the back of the device base.
3. Guide the suction line upwards and through the opening towards the front, as
illustrated.

Mounting Liquistation CSF34
20 Endress+Hauser
1
2
A0013704
 9 Sample supply from below
1 Gland for the suction line
2 Suction line
Connecting the suction line on version with vacuum pump
1
2
3
4
A0013707
 10 Connecting the suction line from the side (as-delivered
state)
1 Hose
2 Fixing clip for hose gland
3 Thread adapter nut
4 Hose gland
A0013708
 11 Suction line connected from below
Modification of the suction line from side connection to connection from below
1. Unscrew the thread adapter nut (item 3).
2. Unscrew the hose gland (item 4) from the side panel.
3. Fit the hose gland in the fixing clamp (item 2) as illustrated.
4. Screw the hose tight from above.
5. Attach the hose adapter supplied to the suction line and screw it onto the hose gland
from below.
6. Insert the dummy plugs supplied.