Epson S5u1c17589t21 User manual

Rev.1.0

CMOS 16-BIT SINGLE CHIP MICROCONTROLLER

S5U1C17589T21 Manual

(Software Evaluation Tool for S1C17589)

Evaluation board/kit and Development tool important notice

1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,

or development purposes only. It is not intended to meet the requirements of design for finished products.

2. This evaluation board/kit or development tool is intended for use by an electronics engineer and is not a

consumer product. The user should use it properly and in a safe manner. Seiko Epson dose not assume any

responsibility or liability of any kind of damage and/or fire coursed by the use of it. The user should cease to

use it when any abnormal issue occurs even during proper and safe use.

3. The part used for this evaluation board/kit or development tool may be changed without any notice.

NOTICE

No part of this material may be reproduced or duplicated in any form or by any means without the written

permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.

Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material

or due to its application or use in any product or circuit and, further, there is no representation that this material is

applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any

intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that

anything made in accordance with this material will be free from any patent or copyright infringement of a third

party. When exporting the products or technology described in this material, you should comply with the

applicable export control laws and regulations and follow the procedures required by such laws and regulations.

You are requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical

information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other

military purposes.

All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective

companies.

S5U1C17589T21 Manual Seiko Epson Corporation i

(Rev. 1.0)

Configuration of product number

17xxx

00E1

Devices

■ Packing specifications

00: Besides tape & reel

0A: TCP BL 2 directions

0B: Tape & reel BACK

0C: TCP BR 2 directions

0D: TCP BT 2 directions

0E: TCP BD 2 directions

0F: Tape & reel FRONT

0G: TCP BT 4 directions

0H: TCP BD 4 directions

0J: TCP SL 2 directions

0K: TCP SR 2 directions

0L: Tape & reel LEFT

0M: TCP ST 2 directions

0N: TCP SD 2 directions

0P: TCP ST 4 directions

0Q: TCP SD 4 directions

0R: Tape & reel RIGHT

99: Specs not fixed

■ Specification

■ Package

D: Bare chip

F: QFP

B: BGA, WCSP

■ Model number

■ Model name

C: Microcontroller, digital products

■ Product classification

S1: Semiconductor

S5U1

17000

Development tools

■ Packing specifications

00: Standard packing

■ Version

1: Version 1

■ Tool type

Hx: ICE

Tx: Evaluation board

Cx: Compiler package

Yx: Programmer software

■ Corresponding model number

17xxx: For S1C17xxx

■ Tool classification

C: Microcontroller use

■ Product classification

S5U1: Development tool

for semiconductor products

ii Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

Table of Contents

1. Overview ....................................................................................................................1

1.1 Directions for Use ................................................................................................................... 2

2. Name and Function of Each Part ..............................................................................4

2.1 Name of Each Part .................................................................................................................. 4

2.2 Function of Each Part ............................................................................................................. 5

2.2.1 Functions of Jumper Switches ............................................................................................ 5

2.2.2 Function of Each Part ......................................................................................................... 5

3. Block Diagram ...........................................................................................................6

4. Connectors.................................................................................................................7

4.1 Extension Interface Connectors (J1–J4) ............................................................................... 7

4.2 Debug Interface Connectors (J6, J7) ..................................................................................... 9

4.3 Power Supply Connectors (J5, J8) ........................................................................................ 9

Appendix A Circuit Diagram and Parts List ...............................................................10

Revision History.............................................................................................................12

1. Overview

S5U1C17589T21 Manual Seiko Epson Corporation 1

(Rev. 1.0)

1. Overview

The S5U1C17589T21 is an evaluation board for the Seiko Epson single-chip microcontroller S1C17589. This

board includes an S1C17589, a GPIO interface, and debug interface connectors.

1) CPU

S1C17589 (QFP15-100pin)

2) CPU clock

Internal oscillators

OSC1: 32.768 kHz crystal resonator

OSC3: 16 MHz crystal resonator

3) Devices mounted

S1C17589 (16-bit MCU)

Crystal resonator (32.768 kHz)

Crystal resonator (16 MHz)

Reset switch

Jumper switch for current consumption measurement × 2

Debug interface connector × 2

4) Operating temperature range

5 °C to 35 °C

5) Operating voltage range

HVDD = 1.8 V to 5.5 V, AVDD = 2.7 V to 5.5 V

Note! Be sure to avoid using chlorinated solvents on this board. Depending on the on-board component, they

may cause corrosion that interferes with using the board safely.

1. Overview

2 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

1.1 Directions for Use

An S1C17589 software debugging and evaluation environment can be constructed with the procedure shown

below.

(1) Using the exclusive cables supplied with the ICDmini, connect the 4-pin target interface connector on the

ICDmini (S5U1C17001H) and connector J6 on this board, and between the 4-pin Flash programming power

supply connector on the ICDmini and connector J7 on this board.

(2) Install jumpers to JP1 and JP2 that are used to measure current consumption if they have been removed.

(3) Supply power to the power supply connector headers (J5 and J8) on this board from the S5U1C17001H2

(ICDmini Ver. 2) or a stabilized power supply. The power supply voltage must be within the S1C17589

operating voltage range.

(4) Connect the ICDmini to the PC using the USB cable supplied with the ICDmini.

The DIP switches on the ICDmini (SW4 and SW5 to select the DSIO signal level) should be set to “Voltage input

from the target system.” If the S5U1C17001H2 (ICDmini Ver. 2) is used as the emulator and the flash

erasing/programming voltage is supplied from the ICDmini, set DIP SW8 on the ICDmini to configure the flash

programming voltage output to be enabled.

Figure 1.1.1 Connections for Software Debugging

S5U1C17001H

For connecting

target system

For flash program-

ming power supply

USB cable

ICDmini (S5U1C17001H)

 Use the power supply in the ICDmini

Ver. 2 or a stabilized power supply.

Stabilized

power supply

1 2 3 4 5 6 7 8

ICDmini DIP switch

setting

OFF

This board

(S5U1C17589T2100)

1. Overview

S5U1C17589T21 Manual Seiko Epson Corporation 3

(Rev. 1.0)

Supply power to the power supply connector headers (J5 and J8) on this board from a stabilized power supply.

The power supply voltage must be within the S1C17589 operating voltage range.

Figure 1.1.2 Connections for Free Running with an External Power Supply

Stabilized power

supply

CN3 (J4)

This board

(S5U1C17589T2100)

2. Name and Function of Each Part

4 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

2. Name and Function of Each Part

2.1 Name of Each Part

The figure below shows the name and function of each part.

Figure 2.1.1 Component Names Mounted on S5U1C17589T21

2. Name and Function of Each Part

S5U1C17589T21 Manual Seiko Epson Corporation 5

(Rev. 1.0)

2.2 Function of Each Part

2.2.1 Functions of Jumper Switches

Table 2.2.1.1 List of Jumper Switch Functions

Name

Function

Factory setting

Optional setting

JP1

S1C17589 current consumption

measurement (AVDD) 1

Short-circuited

Open

JP2

S1C17589 current consumption

measurement (HVDD) *1

Short-circuited

Open

JP3

External power supply monitor at

EXSVD pin

Pins 1 and 2

short-circuited

• Pins 1 and 2 short-circuited

The EXSVD pin is connected to the VDD

voltage.

• Pins 1 and 2 short-circuited

The EXSVD pin is connected to TP8 to

monitor the external voltage.

1 To measure current consumption of the S1C17589 alone, insert an ammeter between the jumper switches.

2.2.2 Function of Each Part

Table 2.2.2.1 List of Parts and Functions

Part name

Location

Function

S1C17589 (16-bit MCU)

Connector headers

J1–J4

Extension interface connector headers (foot pattern only)

Connectors

J6, J7

Debug interface connectors (for connecting with S5U1C17001H)

Connectors

J5, J8

External power supply connectors

Switch

SW1

Reset input

Jumper

JP1

Jumper for AVDD current measurement

Jumper

JP2

Jumper for HVDD current measurement

Jumper

JP3

Jumper for switching voltage to be monitored at the EXSVD pin

Monitor pin

TP1 (AVDD2)

Through hole for AVDD2

Monitor pin

TP2 (AVDD)

Through hole for AVDD

Monitor pin

TP3 (VPP)

Through hole for VPP (Flash programming power supply)

Monitor pin

TP4,TP7 (GND)

Through hole for GND

Monitor pin

TP5, TP9 (HVDD2)

Through hole for HVDD2

Monitor pin

TP6 (HVDD)

Through hole for HVDD

Monitor pin

TP8 (EXSVD)

Through hole for inputting an external voltage to be monitored

Crystal resonator

16 MHz

Crystal resonator

32.768 kHz

3. Block Diagram

6 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

3. Block Diagram

The figure below shows the block diagram of the S5U1C17589T21.

Figure 3.1 S5U1C17589T21 Block Diagram

4. Connectors

S5U1C17589T21 Manual Seiko Epson Corporation 7

(Rev. 1.0)

4. Connectors

4.1 Extension Interface Connectors (J1–J4)

Table 4.1.1 Extension Interface Connector (J1) Pin Assignment Table

No.

Pin name

I/O

Function

No.

Pin name

I/O

Function

HVDD

–

Power supply (+)

P60

I/O

P60/EXCL20/UPMUX

HVDD

–

Power supply (+)

P61

I/O

P61/EXCL30/UPMUX

P40

I/O

P40

P62

I/O

P62/UPMUX

P41

I/O

P41

P63

I/O

P63/UPMUX

P42

I/O

P42

P64

I/O

P64/UPMUX

P43

I/O

P43

P65

I/O

P65/UPMUX

P44

I/O

P44

P66

I/O

P66/UPMUX

P45

I/O

P45

P67

I/O

P67/UPMUX

P46

I/O

P46

N.C.

–

P47

I/O

P47

N.C.

–

N.C.

–

N.C.

–

N.C.

–

N.C.

–

P50

I/O

P50

N.C.

–

P51

I/O

P51

N.C.

–

P52

I/O

P52

N.C.

–

P53

I/O

P53

N.C.

–

P54

I/O

P54

N.C.

–

P55

I/O

P55

N.C.

–

GND

–

Power supply (–)

–

GND

–

Power supply (–)

Table 4.1.2 Extension Interface Connector (J2) Pin Assignment Table

No.

Pin name

I/O

Function

No.

Pin name

I/O

Function

HVDD

–

Power supply (+)

N.C.

–

HVDD

–

Power supply (+)

N.C.

–

P70

I/O

P70/UPMUX

P90

I/O

P90/RTC1S/RTCINT

P71

I/O

P71/UPMUX

P91

I/O

P91/EXCL01

P72

I/O

P72/UPMUX

P92

I/O

P92/EXCL11

P73

I/O

P73/UPMUX

P93

I/O

P93/EXOSC

P74

I/O

P74/EXCL21/UPMUX

P94

I/O

P94

P75

I/O

P75/EXCL31/UPMUX

P95

I/O

P95

P76

I/O

P76/UPMUX

P96

I/O

P96

P77

I/O

P77/UPMUX

N.C.

–

N.C.

–

N.C.

–

N.C.

–

N.C.

–

P80

I/O

P80

N.C.

–

P81

I/O

P81

N.C.

–

P82

I/O

P82

N.C.

–

P83

I/O

P83

N.C.

–

P84

I/O

P84

N.C.

–

P85

I/O

P85

N.C.

–

P86

I/O

P86

GND

–

Power supply (–)

P87

I/O

P87

GND

–

Power supply (–)

4. Connectors

8 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

Table 4.1.3 Extension Interface Connector (J3) Pin Assignment Table

No.

Pin name

I/O

Function

No.

Pin name

I/O

Function

HVDD

–

Power supply (+)

N.C.

–

HVDD

–

Power supply (+)

N.C.

–

N.C.

–

PA0

I/O

PA0

N.C.

–

PA1

I/O

PA1

N.C.

–

PA2

I/O

PA2

N.C.

–

PA3

I/O

PA3

N.C.

–

PA4

I/O

PA4

N.C.

–

PA5

I/O

PA5

N.C.

–

N.C.

–

N.C.

–

N.C.

–

N.C.

–

P00

I/O

P00/UPMAX

N.C.

–

P01

I/O

P01/UPMAX

N.C.

–

P02

I/O

P02/UPMAX

#RESET

P03

I/O

P03/UPMAX

N.C.

–

P04

I/O

P04/UPMAX

PD0

I/O

DST2/PD0

P05

I/O

P05/UPMAX

N.C.

–

P06

I/O

P06/UPMAX

PD1

I/O

DSIO/PD1

P07

I/O

P07/UPMAX

N.C.

–

GND

–

Power supply (–)

PD2

I/O

DCLK/PD2

GND

–

Power supply (–)

Table 4.1.4 Extension Interface Connector (J4) Pin Assignment Table

No.

Pin name

I/O

Function

No.

Pin name

I/O

Function

HVDD

–

Power supply (+)

N.C.

–

HVDD

–

Power supply (+)

N.C.

–

P10

I/O

P10/ADIN00

P30

I/O

P30/#ADTRG0/UPMUX

P11

I/O

P11/ADIN01

P31

I/O

P31/#ADTRG1/UPMUX

P12

I/O

P12/ADIN02

P32

I/O

P32/EXCL00/UPMUX

P13

I/O

P13/ADIN03

P33

I/O

P33/EXCL10/UPMUX

P14

I/O

P14/ADIN04

P34

I/O

P34/REMO/UPMUX

P15

I/O

P15/ADIN05

P35

I/O

P35/FOUT/UPMAX

P16

I/O

P16/ADIN06

P36

I/O

P36/CLPLS/UPMAX

P17

I/O

P17/ADIN07

P37

I/O

P37/UPMAX

N.C.

–

N.C.

–

N.C.

–

N.C.

–

P20

I/O

P20/ADIN10

N.C.

–

P21

I/O

P21/ADIN11

N.C.

–

P22

I/O

P22/ADIN12

AVDD

–

Power supply (+)

P23

I/O

P23/ADIN13

AVDD

–

Power supply (+)

P24

I/O

P24/ADIN14

N.C.

–

P25

I/O

P25/ADIN15

N.C.

–

P26

I/O

P26/ADIN16

GND

–

Power supply (–)

P27

I/O

P27/ADIN17

GND

–

Power supply (–)

4. Connectors

S5U1C17589T21 Manual Seiko Epson Corporation 9

(Rev. 1.0)

4.2 Debug Interface Connectors (J6, J7)

Table 4.2.1 Debug Interface Connector (J6) Pin Assignment Table

No.

Pin name

I/O

Function

DCLK

Clock signal output for debugging

GND

–

Power supply (GND)

DSIO

I/O

Serial communication signal

input/output for debugging

DST2

Debug status signal output

Note! Make sure of the connector direction before connecting this board to the ICDmini.

Table 4.2.2 Debug Interface Connector (J7) Pin Assignment Table

No.

Pin name

I/O

Function

VPP

Flash programming voltage input

GND

–

Power supply (GND)

RESET

Target reset signal input

VCCIN

Target operating voltage output

4.3 Power Supply Connectors (J5, J8)

Table 4.3.1 AVDD Power Supply Connector (J5) Pin Assignment Table

No.

Pin name

Function

AVDD-IN

AVDD power supply

Supply a power voltage even if the A/D

converter is not used.

GND

Power supply (GND)

Table 4.3.2 HVDD Power Supply Connector (J8) Pin Assignment Table

No.

Pin name

Function

HVDD-IN

HVDD power supply

GND

Power supply (GND)

Appendix A Circuit Diagram and Parts List

10 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

Appendix A Circuit Diagram and Parts List

S5U1C17589T21 Manual Seiko Epson Corporation 11

(Rev. 1.0)

Table A.1 S5U1C17589T21 Parts List 1

Item

Quantity

Reference

Part

Manufacture

C1, C3, C4, C6, C9, C14, C20, C24

10 µF/10 V

LMK107BBJ106MALT

TAIYO YUDEN CO., LTD.

C2, C5, C7, C8, C10, C11, C12,

C13, C15, C16, C21, C25

0.1 µF/10 V

GRM188B31H104K

Murata Manufacturing Co., Ltd.

C17, C19, C22, C23

–

Not mounted.

C18

1 µF/10 V

GRM188B31E105K

Murata Manufacturing Co., Ltd.

R3, R6, R9

–

Not mounted.

PG1111C

STANLEY ELECTRIC CO., LTD.

JP2, JP1

A2-2PA-2.54DSA

HIROSE ELECTRIC CO., LTD.

JP3

A2-3PA-2.54DSA

HIROSE ELECTRIC CO., LTD.

J1, J2, J3, J4

–

Not mounted.

J8, J5

S2B-XH-A(LF)(SN)

J.S.T. Mfg. Co.,Ltd.

A2-4PA-2.54DS(71)

HIROSE ELECTRIC CO., LTD.

S04B-PASK-2(LF)(SN)

J.S.T. Mfg. Co.,Ltd.

R2, R1

10 kΩ

MCR03EZPJ103

ROHM Co., Ltd.

R7, R4

0 Ω

MCR03EZPJ000

ROHM Co., Ltd.

33 Ω

MCR03EZPJ330

ROHM Co., Ltd.

680 Ω

MCR03EZPJ681

ROHM Co., Ltd.

SH1, SH2, SH3

XJ8A-0211

OMRON Corporation

SW1

SKRAAKE010

ALPS ELECTRIC CO., LTD.

S1C17589

SEIKO EPSON CORPORATION

FA-238 16 MHz

SEIKO EPSON CORPORATION

MC-146 32.768 kHz

SEIKO EPSON CORPORATION

(Spacer)

AS-315

Hirosugi-Keiki Co., Ltd.

(Round head screw with washer)

B-0306-N

Hirosugi-Keiki Co., Ltd.

1 Parts are subject to change without notice.

Revision History

12 Seiko Epson Corporation S5U1C17589T21 Manual

(Rev. 1.0)

Revision History

Attachment-1

Rev. No.

Date

Page

Popular Microcontroller manuals by other brands

MAS

MAS CIKA MDVKIT35P quick start guide

SONIX

SONIX SN8P2977 user manual

NXP Semiconductors

NXP Semiconductors P89LPC9321 UM10310 user manual

ANTUMBRA

ANTUMBRA TUNE Building instructions

Fujitsu

Fujitsu MB89140 Series Hardware manual

Texas Instruments

Texas Instruments AM5728 user guide

Qorvo

Qorvo QM33120WDK1 quick start guide

AnyDATA

AnyDATA DTS-800 CDK Service manual

SCORPIO TECHNOLOGY

SCORPIO TECHNOLOGY TRANSISTOR TESTER quick start guide

ScioSense

ScioSense AS6040-DK user guide

Kinco

Kinco K5 Series Hardware manual

Dialog Semiconductor

Dialog Semiconductor DA14530/1 Hardware user manual

Intel

Intel Agilex F Series user guide

Atmel

Atmel AVR2052 quick start guide

NimbeLink

NimbeLink Microchip chipKIT WF32 Shield user manual

NXP Semiconductors

NXP Semiconductors MCIMX6UL-EVK quick start guide

Novatel

Novatel Wireless Expedite G301 Series manual

Texas Instruments

Texas Instruments MSP432P401R quick start guide

Epson S5U1C17589T21 User manual

Popular Microcontroller manuals by other brands