Epson S5U1C17611T2 User manual

CMOS 16-BIT SINGLE CHIP MICROCONTROLLER
S5U1C17611T2 Manual
(Software Evaluation Tool for S1C17611)
Rev.1.0

Evaluation board/kit and Development tool important notice
1. This evaluation board/kit or development tool is designed for use for engineering evaluation, demonstration,
or development purposes only. Do not use it for other purpose. It is not intended to meet the requirement of
design for finished product.
2. This evaluation board/kit or development tool is intended for use by an electronics engineer, and it is not the
product for consumer. The user should use this goods properly and safely. Seiko Epson dose not assume any
responsibility and liability of any kind of damage and/or fire coursed by usage of it. User should cease to use
it when any abnormal issue occurs even during proper and safe use.
3. The part used for this evaluation board/kit or development tool is changed without any notice.
NOTICE
No part of this material may be reproduced or duplicated in any form or by any means without the written
permission of Seiko Epson. Seiko Epson reserves the right to make changes to this material without notice.
Seiko Epson does not assume any liability of any kind arising out of any inaccuracies contained in this material
or due to its application or use in any product or circuit and, further, there is no representation that this material is
applicable to products requiring high level reliability, such as, medical products. Moreover, no license to any
intellectual property rights is granted by implication or otherwise, and there is no representation or warranty that
anything made in accordance with this material will be free from any patent or copyright infringement of a third
party. When exporting the products or technology described in this material, you should comply with the
applicable export control laws and regulations and follow the procedures required by such laws and regulations.
You are requested not to use, to resell, to export and/or to otherwise dispose of the products (and any technical
information furnished, if any) for the development and/or manufacture of weapon of mass destruction or for other
military purposes.
All brands or product names mentioned herein are trademarks and/or registered trademarks of their respective
companies.
©SEIKO EPSON CORPORATION 2012, All rights reserved.

Configuration of product number
Devices
S1 C 17xxx F 00E1 00
Development tools
S5U1 C17000 Y2 1 00
Packing specifications
00: Besides tape & reel
0A: TCP BL 2 directions
0B: Tape & reel BACK
0C: TCP BR 2 directions
0D: TCP BT 2 directions
0E: TCP BD 2 directions
0F: Tape & reel FRONT
0G: TCP BT 4 directions
0H: TCP BD 4 directions
0J: TCP SL 2 directions
0K: TCP SR 2 directions
0L: Tape & reel LEFT
0M: TCP ST 2 directions
0N: TCP SD 2 directions
0P: TCP ST 4 directions
0Q: TCP SD 4 directions
0R: Tape & reel RIGHT
99: Specs not fixed
Specification
Package
[D: die form; F: QFP, B: BGA]
Model number
Model name
[C: microcomputer, digital products]
Product classification
[S1: semiconductor]
Packing specifications
[00: standard packing]
Version
[1: Version 1]
Tool type
Hx: ICE
Dx: Evaluation board
Ex: ROM emulation board
Mx: Emulation memory for external ROM
Tx: A socket for mounting
Cx: Compiler package
Sx: Middleware package
Yx: Writer software
Corresponding model number
[17xxx: for S1C17xxx]
Tool classification
[C: microcomputer use]
Product classification
[S5U1: development tool for semiconductor
products］

Table of Contents
1. Overview..................................................................................................................... 1
1.1 Usage Method ..........................................................................................................................1
2. Block Diagram............................................................................................................ 2
3. Hardware Information................................................................................................ 3
3.1 Layout Information .................................................................................................................. 3
3.2 Jumper, and Each Type of Mounting Pattern ........................................................................4
3.3 Circuit Diagram........................................................................................................................5
3.4 Parts List ..................................................................................................................................6
Revision History............................................................................................................... 7
S5U1C17611T2 Manual Seiko Epson Corporation i
(Rev.1.0)

1. Overview
1. Overview
S5U1C17611T2 (S5U1C17611T2: Software Evaluation Tool for S1C17611) is an evaluation and development
support board for the S1C17611 single-chip microcontroller made by Seiko Epson.
S5U1C17611T2 has built-in S1C17611 and crystal unit, and the terminals of S1C17611 are outputted at the
through holes on the board.
S5U1C17611T2 can be used as the software development environment of S1C17611 by connecting to the
S5U1C17001H (ICD mini) and S5U1C17002H (ICD board) emulators made by Seiko Epson.
1.1 Usage Method
The software development environment of S1C17611 can be built through the following steps.
<When S5U1C17001H (ICD mini) is used>
(1) Connect ICD mini to J2 and J6 of S5U1C17611T2 using the dedicated cable that comes with the ICD
mini.*1
(2) Provide power supply*2through connector (J8) for power supply.
(3) Connect ICD mini to PC*3using the USB cable that comes with the ICD mini.
<When S5U1C17002H (ICD board) is used>*4
(1) Connect ICD board to J1 of S5U1C17611T2 such that the pin numbers on both sides match.*5
(2) Connect ICD board to PC*3using the USB cable that comes with the ICD board.
*1 For the connection between ICD mini and S5U1C17611T2, refer to the S5U1C17001H user manual.
*2 It is prohibited to apply voltage in excess of the supply voltage input range of S1C17611. For the supply
voltage input range of S1C17611, refer to the S1C17611 technical manual.
*3 It is necessary for the software development tool (S5U1C17001C) to be installed.
*4 Simultaneous power supply from ICD board and power supply connector (J8) is prohibited. It causes
damage to S5U1C17611T2.
*5 3.3V supply voltage is provided to S5U1C17611T2 by connecting to ICD board.
S5U1C17611T2 Manual Seiko Epson Corporation 1
(Rev.1.0)

2. Block Diagram
2. Block Diagram
The block diagram of S5U1C17611T2 is as shown in Figure 2.1.
S5U1C17001H
Figure 2.1 S5U1C17611T2 block diagram
Debug I/F
32kHz
Crystal Unit (X1)
8MHz
Crystal Unit (X2)
Reset SW
(SW1)
ICD mini I/F
Connector (J2,J6)
S5U1C17611T21
S1C17611
ICD board I/F
Connector (J1)
S5U1C17002H
OSC1
OSC3
Pins Extension
connector
(J3,J4,J5,J7)
(Not Mounted)
External Power
Supply (J8)
Power
Supply
LED (D1)
VDD
RESET
2 Seiko Epson Corporation S5U1C17611T2 Manual
(Rev.1.0)

3. Hardware Information
3. Hardware Information
3.1 Layout Information
The parts layout of S5U1C17611T2 is as shown in Figure 3.1.
*1 The J3, J4, J5 and J7 connectors are for patternization only. The connector parts are included with the
main product, so mount and use when required.
Figure 3.1 S5U1C17611T2 parts layout
8MHz
Crystal Unit (X2) Reset SW
(SW1)
LED (D1)
S1C17611 (U10)
32kHz
Crystal Unit (X1)
ICD mini I/F
connector (J2, J6)
Power supply
connector (J8)
Extension
connector (J5)
(foot pattern only*1)
Extension
connector (J7)
(foot pattern only*1)
ICD board I/F
connector (J1)
(on the reverse side)
Extension
connector (J3)
(foot pattern only*1)
Extension
connector (J4)
(foot pattern only*1)
Jumper for Power supply
to AVDD on S1C17611 Jumper for Power supply
to VDD on S1C17611 (JP1)
(
JP2
)
S5U1C17611T2 Manual Seiko Epson Corporation 3
(Rev.1.0)

3. Hardware Information
3.2 Jumper, and Each Type of Mounting Pattern
The list of jumper functions of S5U1C17611T2 is as shown in Figure 3.1. In addition, each type of mounting
pattern is as shown in Table 3.2.
Table 3.1 List of jumper functions
Jumper Jumper Type Setting When Shipped Selectable Function
JP1 Pin Connected: VDD supply to S1C17611 Unconnected: No VDD supply to
S1C17611
JP2 Pin Connected: AVDD supply to S1C17611 Unconnected: No AVDD supply to
S1C17611
JP3 Solder bridge Unconnected: OSC3 is unconnected to
J5-17 pin Connected: OSC3 connected to J5-17 pin
JP4 Solder bridge Unconnected: OSC4 is unconnected to
J5-20 pin Connected: OSC4 connected to J5-20 pin
JP5 Solder bridge Connected: OSC3 is connected to X2
(Crystal unit) Unconnected: OSC3 unconnected to X2 (Crystal unit)
JP6 Solder bridge Connected: OSC4 is connected to X2
(Crystal unit) Unconnected: OSC4 unconnected to X2 (Crystal unit)
JP7 Solder bridge Connected: P07/RFIN is connected to
J7-15 pin Unconnected: P07/RFIN unconnected to J7-15 pin
JP8 Solder bridge Connected: P11/SENA is connected to
J7-17 pin Unconnected: P11/SENA unconnected to J7-17 pin
JP9 Solder bridge Connected: P10/REF is connected to J7-16
pin Unconnected: P10/REF unconnected to J7-16 pin
JP10 Solder bridge Connected: P12/SENB is connected to
J7-18 pin Unconnected: P12/SENB unconnected to J7-18 pin
JP11 Solder bridge Connected: P12/SCLK is connected to
J5-12 pin Unconnected: P12/SCLK unconnected to J5-12 pin
JP12 Solder bridge Connected: P14/SIN is connected to J5-4
pin Unconnected: P14/SIN unconnected to J5-4 pin
JP13 Solder bridge Connected: P13/SOUT is connected to
J5-8 pin Unconnected: P13/SOUT unconnected to J5-8 pin
Table 3.2 Each mounting pattern
Location Mounting pattern Remarks
J3 2 rows×20-pin connector (2.54mm pitch) Comes with the connector (FFC-40BMEP1B)
J4 2 rows×20-pin connector (2.54mm pitch) Comes with the connector (FFC-40BMEP1B)
J5 2 rows×20-pin connector (2.54mm pitch) Comes with the connector (FFC-40BMEP1B)
J7 2 rows×20-pin connector (2.54mm pitch) Comes with the connector (FFC-40BMEP1B)
SENR1 Thermistor, humidity sensor (2.54mm pitch) For external connection of RF converter*1
SENR2 Thermistor, humidity sensor (2.54mm pitch) For external connection of RF converter*1
SENR3 Thermistor, humidity sensor (2.54mm pitch) For external connection of RF converter*1
R7 Chip resistor (2.0×1.25mm) For external connection of RF converter*1
R9 Chip resistor (2.0×1.25mm) For external connection of RF converter*1
C25 Chip capacitor (2.0×1.25mm) For external connection of RF converter*1
*1 This mounting pattern is assumed to be built into the external circuit of RF converter and the parts are not
built-in.
4 Seiko Epson Corporation S5U1C17611T2 Manual
(Rev.1.0)

3. Hardware Information
S5U1C17611T2 Manual Seiko Epson Corporation 5
3.3 Circuit Diagram
Figure 3.2 S5U1C17611T2 circuit diagra
(Rev.1.0)

3. Hardware Information
3.4 Parts List
Table 3.3 S5U1C17611T2 parts list*1
Parts Name Location Model No., Specs Qty. Manufacturer
MCU U10
S1C17611F
(TQFP12-48) 1 SEIKO EPSON CORPORATION
Crystal unit X1 C-002RX 32.768kHz
12.5pF/20PPM 1 EPSON TOYOCOM CORPORATION
Crystal unit X2 MA-406 8MHz
16pF/50PPM 1 EPSON TOYOCOM CORPORATION
Voltage detection IC U9 S-1000N18-M5T1G 1 Seiko Instruments Inc.
General-purpose logic U3 SN74LVC1G97DCK 1 Texas Instruments
LED D1 PG1111C 1 STANLAY ELECTRIC CO., LTD.
Diode D2 CRS06(Q) 1 TOSHIBA CORPORATION
Ferrite beads F1 BLM18PG330SN1D 1 Murata Manufacturing Co., Ltd.
Switch SW1 SKRAAKE010 1 ALPS ELECTRIC CO., LTD.
Connector J1 PS-10SD-D4T1-1 1 Japan Aviation Electronics Industry, Ltd.
Connector J2 A2-4PA-2.54DS(71) 1 HIROSE ELECTRIC CO., LTD.
Connector J6 S04B-PASK-2(LF)(SN) 1 JST Mfg. Co., Ltd
Connector J8 S2B-XH-A(LF)(SN) 1 JST Mfg. Co., Ltd
Jumper pin JP1, JP2 2
Jumper socket JP1, JP2 2
C1 5pF 1
C2, C5, C6, C7,
C8, C9, C11,
C12, C13, C14,
C15, C16, C18,
C19, C20, C21,
C22, C23, C24,
C35, C36
0.1μF 21
C3,C4 15pF 2
C10, C17 3.3μF 2
C26, C27, C28,
C29, C30, C31,
C32 10μF 7
Ceramic chip
capacitor
C33, C34 4.7μF 2
R1 10kΩ1
R2 47kΩ1
R3, R5 0Ω2
R4 470kΩ1
R6 680Ω1
Chip resistor
R8 33Ω1
Power cable (housing) Included XHP-2 1 JST Mfg. Co., Ltd
Power cable (contact) Included 2
Power cable (wire) Included 2
Spacer Included 4
Flat washer Included 4
Connector Included (can
mount to J3, J4,
J5, J7) FFC-40BMEP1B 4 Honda Tsushin Kogyo Co., Ltd.
*1 There may be changes to built-in parts without prior notice.
6 Seiko Epson Corporation S5U1C17611T2 Manual
(Rev.1.0)

Revision History
Revision History
Attachment-1
Code No. Page Contents
411889900 All First edition
S5U1C17611T2 Manual Seiko Epson Corporation 7
(Rev.1.0)

International Sales Operations
AMERICA
EPSON ELECTRONICS AMERICA, INC.
214 Devcon Drive,
San Jose, CA 95112, USA
Phone: [phone] FAX: [phone]
EUROPE
EPSON EUROPE ELECTRONICS GmbH
Riesstrasse 15, 80992 Munich,
GERMANY
Phone: [phone] FAX: [phone]
ASIA
EPSON (CHINA) CO., LTD.
7F, Jinbao Bldg., No.89 Jinbao St.,
Dongcheng District,
Beijing 100005, CHINA
Phone: [phone] FAX: [phone]
SHANGHAI BRANCH
7F, Block B, Hi-Tech Bldg., 900 Yishan Road,
Shanghai 200233, CHINA
Phone: [phone] FAX: [phone]
SHENZHEN BRANCH
12F, Dawning Mansion, Keji South 12th Road,
Hi-Tech Park, Shenzhen 518057, CHINA
Phone: [phone] FAX: [phone]
EPSON HONG KONG LTD.
Unit 715-723, 7/F Trade Square, 681 Cheung Sha Wan Road,
Kowloon, Hong Kong.
Phone: [phone] FAX: [phone]
EPSON TAIWAN TECHNOLOGY & TRADING LTD.
14F, No. 7, Song Ren Road,
Taipei 110, TAIWAN
Phone: [phone] FAX: [phone]
EPSON SINGAPORE PTE., LTD.
1 HarbourFront Place,
#03-02 HarbourFront Tower One, Singapore 098633
Phone: [phone] FAX: [phone]
SEIKO EPSON CORP.
KOREA OFFICE
5F, KLI 63 Bldg., 60 Yoido-dong,
Youngdeungpo-Ku, Seoul 150-763, KOREA
Phone: [phone] FAX: [phone]
SEIKO EPSON CORP.
MICRODEVICES OPERATIONS DIVISION
IC Sales & Marketing Department
421-8, Hino, Hino-shi, Tokyo 191-8501, JAPAN
Phone: [phone] FAX: [phone]
Document Code: 411889900a
First Issue:February 2010
Revised:December 2012 in JAPAN