Erreka TEMIS User manual

G
E F
A
B
D
C
TC H
I
0
TEMIS
Quick Installation Guide MSB-026/04
WARNING
Elements of the complete installation
150
160
170
180
190
150 160 170 180 190
AB
200
210
200 210140
140
>120° 110°~120°
100°~110°
90°~100°
AD
C
BD Aprox
TATA
This quick guide is a summary of the complete installation manual. The manual contains safety warnings and
other explanations which must be taken into account. The installation manual can be downloaded by going
to the "Downloads" section of Erreka website:
http://www.erreka-automation.com
Electrical Wiring
A.B: 24v DC Motor(2x1mm²)
C: Photocell 2x0.5mm² (max 20m)
D: Control Box (3x1.5mm²)
E: Push Botton 2x0.5mm²(max 25m)
Assembly levels, inward opening
TEMIS It is not applicable to an insecure or lacking rigidity door nor solves the defects due to incorrect installation or mainte-
Check the following points before starting the installation:
1). Hinges are properly positioned and greased.
2). No obstacles in the moving area and no frictions between two gate leafs or with the ground while moving.
3). “C” value is 139mm.
4). “D” can be measured from the gateeasily.
5). “A” = “C” + “D”
6). The value of “B” can be calculated from the value of “A” and the leaves opening angle.
Ex. If “A”=160mm with the leaves opening angle of 100 degrees, then the value of “B” is approximate 190mm.
Please make sure B and A are similar or the same in value that the leaves can be
operated smoothly, also to reduce the burden of the motor.
Open Interior
F: Key Selector(2x0.5 mm²)
G: Flash Light (2x0.5mm²)
H.I: Electric Lock (2x1mm²)
TA: Open Stopper
TC: Closed Stopper
1

Assembly
Unlocking
Unlocking for manual operation: Motorised operation locking:
1 2
Place the two brackets on the surface and the
position where they will be installed, please make
sure that the front bracket is installed completely
horizontally.
Place the motor on rear bracket with screw (A) and nut (B).
1 1
1. Insert the key to the release slot.
2. Turn counterclockwise to release the motor.
1. Insert the key and turn clockwise .
2. Remove the key.
A
B
2
1
1
2
Assembly levels, outward opening
Please make sure B and A are similar or the same in value that the leaves can be operated smoothly, also to
reduce the burden of the motor.
Open exterior
A
B
2

3 4
Release the gate opener with the door in closed
position. Place the front bracket without xing it..
Check the door manually which can be moved easily in
entire route.
Horizontal 180O
Technical Feature
Dimensions
Max gate length
Max gate weight
Power supply
Motor power supply
Gear Type
Peak Thrust
Normal Thrust
Operation Stroke
Piston extention
Opening Time
Duty Cycle
Protection Grade (IP)
Operation temperature
Absorbed current (A)
Absorbed Power (W)
Manual Release
Enclosure Dimensions
2.2M
200kg
110V/230VAC (50-60Hz) SMART-D201M / SMART-D201
24VDC
Worm and worm gear
2200N
1500N
400mm
19.8mm/sec
<20 sec
20%
IP44
-20
o
C~+50
o
C
4.2A for 10 sec
60W
Key
803mm*100.5mm*185mm
Block the motor and make the electrical wiring to connect the cables M1 and M2 correctly. If you only
install one gate, connect the wires to the terminal M1.
100mm
100.5mm
185mm
803mm
765mm
ADC
BDAprox
3

Motor 1 Motor 2
(+)
(-)
(+)
(-)
4
Electrical connections
Flash Light 24Vdc
Electric Lock 24Vdc
Key
Selector Push Botton
Transformer
Antenna
TX1 TX2
FT1 FT2
RX1 RX2 Green Box
M2-M1-
Lat-
Lit- Lmt4Lmt3
Lmt2
Lit+ SKey
S1
M2+
M1+Lat+ Ph2Ph1 PhVcc PhVcc
S25V
ANT
GND
DKey GND
GND GND GND
Lmt1 GND
+-
J1
Q17
J5
K5
K3
K2K1
J4 J3
J7
F1
DB1
J8
NC NO
CO
+-
NC NO
CO
+--+
CO
NONC
-+
CO
NONC
NC NO
CO
+-
-
+
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26
LED3
LED4
LED2
LED Display
LED1 System Learning
LED2 RF Learing
LED3 Photocell 1
LED4 Photocell 2
UP
SET
DOWN
RF-LEARN
Batteries recharger incorporated in control board, no need to connect extra recharger.
Maximum batteries capacity connection is up to 15Ah.
The battery housing on the box is prepared for 2 batteries of 1.3 Ah.
Batteries connection

5
Display indications
Operation for Function settings
For example: How to set the Function “F1-2”; the steps are following:
(1) Press the “SET” button for 3seconds, the LED will display F1.
(*) To enter “F2” Function or another Functions, press the “UP”
button to adjust F2 ~ F8.
1.
Step Operations LED Display after the Step
(2) After completing the operation (1) then press the “SET” button
again, you will enter the second option.
(3) Continually, press “UP” button until you search the Function “2”
(**) of F1 as the right hand-side picture. “F1-2” is set completely.
(**) If you would like to set one of Function “0 ~ 8” as the second
option, please press “UP” or “DOWN” button to adjust it.
(4) If you would continue setting up the next Functions, press “SET”
to return the first option, like F1, F2, F3.....etc.
For example, after complete F1-2 setting. You would continue
setting F2-2, please press “SET” to return the formal option. The
LED display shows the first two numbers as the first option F1. And
then follow the operation (*) and (2) ~ (3) until complete the setting.
After setting all Functions you need, then wait for 10 seconds, the
LED will display “RUN”. And you can use transmitter to operate the
gate.
2.
3.
LED Display Programmable Functions
“N-L”: The system learning is not done.
“RUN”: The system is in normal
performing.
“CLN” the memory of the system is all
cleaned/deleted. Press “UP+DOWN”
for 5 seconds.
“STP”: the motor stop in the middle of
the operating process.
“ARN”: The system learning is in
progress.
“ME”: Motor operation error.
“LEA”: Enter learning mode and then
wait for learning instructions.
The operation of gate learging:
(1). Press “SET” + “DOWN” + “UP”
for 3 seconds, and the LED display shows
“LEA” +”DG”; and then press the
transmitter A botton one time. After
1~3seconds, the LED display shows the
current value during learning mode, it
shows 10 for 1A

6
Open/close programming
Gate-moving Logic
(A) In gate-opening phase: the gates stop if the transmitter/push button/key selector is activated, and close when
you press the button again.
(B) In gate-closing phase: the gates stop if the transmitter/push button/key selector is activated, and open when you
press the button again.
(C) In gate-opening or gate-closing phase: For safety purpose, the gates stop if encountering obstacles.
Step1: Set the Function F2-1 for double leaf gate learn; or set the Function F2-2 for single leaf gate learning.
Step2: Press and hold the “UP+SET+DOWN” for 3 seconds. LED show “LEA D-G”.
Step3: Press A button on the transmitter for double leaf gate system learning or B button for single gate.
In system learning mode, the gates will proceed with the following procedures:
$'RXEOH/HDYH*DWH'*0&ORVHĺ0&ORVHĺ02SHQĺ02SHQĺ0&ORVHĺ0&ORVH
%6LQJOH/HDI*DWH6*0&ORVHĺ02SHQĺ0&ORVH
Advise: If change the configuration of F2, you should program the system learning again.
The completion of system learning:
(A) For Double leaf gate (D-G) installation: Show RUN on LED display
(B) For Single leaf gate (S-G) installation: Show RUN on LED display.
Notes:
(A) System learning fails and needs to be learned again when an unpredictable interruption occurs.
In this case, please make sure the Function F3 is in F3-1.
(B) Once the system learning is completed, there is no need to proceed with the learning process again when
there is a power failure.
(C) M2 opens 3 seconds after M1 opens and M1 closes 3 seconds after M2 closes.
Radio code programming
Radio code deleting
1 2 3
Press and hold the RF-Learn button on the PCB for 10 seconds until
blue LED off.
Blue LED ON
1 s 5 s 5 s
RF-Learn
A
B
A
B
Press and hold the RF-Learn for 1
second, the blue LED on the RF board
will be ON.
Press A button for 5 seconds for double leaf
gate Radio code programming installation.
Press B button for 5 seconds for single-gate
installation.
10 s
LED Display

7
¡ ATTENTION ! The 24Vdc flash light output is not fixed output but flashing. To connect a fixed or a fixed mode flash
light for the proper Function.
NOTE (Parameter F9)
Exterior Photocell: Only be activated in case of door closing.
Interior Photocell: Can be activated in door opening and door closing..
Complete programming chart (1)
Encoder/ Limit switch
Number of operators
Maximum trapping force
Gate speed
Slowdown
Soft stop speed
Lapse between leaves in
opening and closing
Semi-automatic or
automatic
operation mode and
stand-by
time (in seconds) in
automatic
mode
Photocell Function mode
(Open-close,
interior-exterior)
Pedestrian opening
Flashing light pre-warning
F1
F2
F3
F4
F5
F6
F7
F8
F9
FA
FB
F1-1
F1-2
F1-3
F2-1
F2-2
F3-1
F3-2
F3-3
F3-4
F4-1
F4-2
F5-1
F5-2
F6-1
F6-2
F7-1
F7-2
F7-3
F7-4
F7-5
F7-6
F7-7
F7-8
F7-9
F8-0
F8-1
F8-2
F8-3
F8-4
F8-5
F8-6
F8-7
F8-8
F9-1
F9-2
F9-3
F9-4
FA-0
FA-1
FB-0
FB-1
Motor only
Motor with limit switch
Motor with encoder
Two Operators
One Operator
2A
3A
4A
5A
100% Full Speed
80% Full Speed
Function ON
Function OFF
70% Full Speed
50% Full Speed
F6-3
35% Full Speed
F6-4
25% Full Speed
2 sec.
3 sec.
4 sec.
5 sec.
6 sec.
7 sec.
8 sec.
9 sec.
10 sec.
OFF
3 sec.
10 sec.
20 sec.
40 sec.
60 sec.
120 sec.
180 sec.
300 sec.
Mode 1
Mode 2
Mode 3
Mode 4
OFF
ON
OFF
On
1. The factory setting is "F1-1".
1. The factory setting is "F2-1".
1. The factory setting is "F3-1".
2. Please make sure that the parameter F3 is always in F3-1
in case of system learning process.
1. The factory setting is "F4-1".
1. The factory setting is "F5-1".
1. The factory setting is "F6-2".
1. The factory setting is "F7-1".
1. The factory setting is "F8-0".
1. The factory setting is "F9-1".
Mode 1: Photocell Exterior FT1- Photocell Interior FT2
Mode 2: Photocell Exterior FT1- Safety Belt FT2
Mode3: Photocell Exterior FT1- Open Device FT2
Mode 4: Photocell Interlock FT1- Fotocélula Interior FT2
1. When Function on and push B key in the transmitter, one
gate will open partically.
2. The factory setting is "FA-0".
1. When Function ON, the light will flash before the gate
operate 3 seconds. If set OFF, the flash light will operate
with motor in the same time.
2. The factory setting is "FB-0".
LED Display Definition Parameter Mode Description

8
Complete programming chart (2)
Note (Parameter F3)
Please set F3 Function after system learning. The LED display 10 to indicate all of the recorded values will increase 1 ampere as
the over current value. In other words, the LED shows 20 to indicate all the recorded values will increase 2 ampere as the over
current value. The value can be adjusted by pressing button UP and DOWN. The maximum value is 40(4.0A) and the minimum
value is 05 (0.5A)
LED Display Definition Parameter Mode Description
Photocell1
Photocell2
Buzzer Function
Reverse Impulse for
Electric Lock
Open/Stop/Close/Stop
Function key
Pedestrian Mode Function
key
Auto-Close Function key
FC
FD
FE
FF
FG
FH
FI
FC-0
FC-1
FD-0
FD-1
FE-0
FE-1
FF-0
FF-1
FG-1
FG-2
FG-3
FG-4
FH-0
FH-1
FH-2
FH-3
FH-4
FI-0
FI-1
FI-2
FI-3
FI-4
OFF
ON
OFF
ON
OFF
ON
OFF
ON
A key
B key
C key
D key
OFF
A key
B key
C key
D key
OFF
A key
B key
C key
D key
1. The factory setting is "FC-0".
1. The factory setting is "FD-0".
1. The factory setting is "FE-0".
1. if the Function is on, the gate will move forward a
little before the gate operate for releasing the Latch
2. The factory setting is "FF-1".
1. The factory setting is "FG-1".
1. The factory setting is "FH-2".
1. The key is to turn on or off the Auto-Close Function.
2. The factory setting is "FI-0".
3. When the flasher and buzzer is running, the auto
closed button has no Function till flasher and buzzer
finish running.