Erreka VIVO-D102 Operating instructions

9
VIVO-D102(M)
Quick installation and programming guide English
IMPORTANT
NOTE
This quick guide is a summary of the complete installation manual. The manual contains safety warnings
and other explanations which must be taken into account. The installation manual can be downloaded by
going to the "Downloads" section at the Erreka website:
http://www.erreka.com/Automatismos/descargaDocumentos.aspx
G
E114A
ELECTRICAL CABLING:
Element Nº threads x section Maximum length
A: Main power supply 3x1.5mm230m
B: Flashing light / Traffic light 2x0.5mm2/ 3x0.5mm220m
C: Photocells (Tx / Rx) 2x0.5mm2/ 4x0.5mm230m
D: Pushbutton/wall key 2x0.5mm250m
E: Operator (motor + encoder) Duct (2x1mm2 + interior screened duct
2x0.5mm2)
8m (maximum 25m with
cable 2x2.5mm2)
F: Operator release 2x0.5mm225m
G: Antenna Coaxial cable 50k(RG-58/U) 5m
Elements of the complete installation

10
D102: 230Vac/ 50Hz
D102M: 125Vac/ 60Hz
MOTOR
ENCODER
STOP
M
MOTOR
ENCODER
P14
P15
P13
G1
G2
M
GND
SNG1
V+
CHG
BAT: (2x12V/1,2 Ah)
BATTERY
IN/OUT
ADO01
General connections
STOP CABLE CONNECTOR:
connect to the release switch
(in the models with encoder
and release). In the models
without release, make an
electrical bridge.
G1 Blue (motor)
G2 Red (motor)
P14 (GND) Mesh (encoder mesh) (–)
P15 (SNG1) Green (encoder signal) (S)
P13 (V+) Brown (encoder power supply) (+)
M114C
D1 and D2:
CL (static) Door closed
CL (flashing) Door closing
OP (static) Door open
OP (flashing) Door opening
XX (countdown) Door on standby
StOP Operator unlocked
PA (static) Pause (operation not complete)
rS (static) Door searching for close position
D3 and D4:
C5 Closing safety device activated
E1 Encoder motor shudown
F1 Thrust limit exceeded
bA Battery working
Ftço Photocells defective (pre-testing)
Display indications

11
Turning direction change and check (C1)
This operation is only necessary if the operator opens the gate instead of closing it when making a reset (rS).
Radio code programming, P1 (only with RSD receiver)
If a receiver other
than RSD is used, see
the corresponding
instructions.
Open/close programming (P3)
The lower closing stopper must be installed before programming the run (see the
operator manual).
OWait whilst the door carries
out the open/close.
If you want the door to stop
before reaching the upper
stopper, press the transmitter
button at the required point.

12
Complete programming chart
D1 D2 Parameter D3 D4
Pre-
determined
option
Options or values
C1Motor turning direction 01x
02
4Disabled
5Closing safety device (photocell or strip) 00xDevice not installed
10 Device without testing
11 Device with testing
P1Total opening radio code programming oç
2Disabled
3Door open/close programming oç
F1Functioning mode 01 Automatic
02xStep-by-step
2Standby in automatic mode 0...5. 0...9 15 59 = 59 sec; 2.5 = 2 min. 50 sec., etc
3Disabled
A0Flashing light 01xNo pre-warning
02 With pre-warning
1Garage light time 0...5. 0...9 03 59 = 59 sec; 2.5 = 2 min. 50 sec., etc
2Door speed 0 1...5 03 01: minimum speed;
05: maximum speed
3Slowdown speed 0 1...5 03 01: minimum speed;
05: maximum speed
4Slowdown distance 0 0...5 00 00: minimum distance;
05: maximum distance
5Disabled
6Maximum thrust
maximum thrust in opening 1...9 X 6X 1X: minimum thrust (in opening);
9X: maximum thrust (in opening)
maximum thrust in closing X 1...9 X6 X1: minimum thrust (in closing);
X9: maximum thrust (in closing)
7Closing photocell used during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
8Pushbutton operation during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
9Opening mode 01xOpening in accordance with the mode
selected in the main functions (F)
02 Collective opening (the control board
does not obey the key commands during
opening)
03 Step-by-step opening (the door halts if a
key device is activated during opening.
The door closes when operated again)
ç1Operations carried out XX Indicates the cycles completed,
multiplying the indicated figure by an
amount, for example:
68 indicates 6,800 cycles completed
6.8 indicates 68,000 cycles completed