Erreka Dolfin Operating instructions

6
DOLFIN
Quick installation and programming guide English
IMPORTANT
NOTE
This quick guide summarises the full installation manual. The full manual contains safety warnings and other
explanations that must be taken into account. You can download the latest version of this guide and the
installation manual in the "Downloads" section of the Erreka website:
http://www.erreka-automation.com
The options and functions described in this guide are applicable from the firmware version indicated on the
circuit. As part of a process of continuous improvement, the firmware is subject to the incorporation of new
functionalities or their extension, and consequently to the generation of new versions not necessarily
compatible with the previous ones. Therefore, if your firmware version is lower than the one indicated in
this guide, some options and functions may not be available or may be different.
Electrical cabling
A: Main power supply
B: Flashing light
C: Photocells (Tx / Rx)
D: Pushbutton/wall key
E: Antenna
Elements of the complete installation
firmware V1.1 or later

7
Unlocking
Unlocking for manual operation:
Turn the key clockwise 270º.
Motorised operation locking:
Turn the key anti-clockwise 270º as far as it
goes (you should hear a CLICK), and move the
gate manually until it interlocks in the drive
mechanism.
Unlocking Locking
D157A D157B
P154A2
>10cm
P154E
1/2 1/2
>10cm
P154F
>10cm
P154G P154L
3
2
1
P154M
Mounting the track and the belt
1 Make the M mark with a pencil. 2 Position the first section of the
profile and the three pins,
respecting their orientation.
3 Position the following profile
sections, ensuring they are securely
fitted.
4 Attach the operator to the base. 5 Position the belt in the attachment
point (1), the cover (2) and the
tensioner nut (3).
6 Tighten the belt
(with the
operator unblocked and the gate
in an intermediate position)
.

8
General connections
L:Line
N: Neutral
T: Earth
F:Mainfuse
230VAC: 2,5A
125VAC: 4A
DL13 24Vac power supply
DL36 5Vdc power supply
DL37 Closing relay activated
DL38 Opening relay activated
EnterEsc
M157C
D1 and D2:
CL (static) Gate closed
CL (flashing) Gate closing
OP (static) Gate open
OP (flashing) Gate opening
PC (flashing) Pedestrian gate closing
PO (static) Pedestrian gate open
PO (flashing) Pedestrian gate opening
XX (countdown) Gate on standby
StOP Operator unlocked
PA (static) Pause (operation not complete)
rS (flashing) Gate searching for close position
D3 and D4:
C4 Opening safety device activated
C5 Closing safety device activated
E1 Encoder motor shutdown
F1 Thrust limit exceeded
bA (static) Battery working
bA (flashing) Battery voltage too low (the board
does not carry out any operations)
Ftço Photocells defective (pre-testing)
Display indications

9
P157I P157J
P157Y
P157Z
Turning direction change and check (C1)
P157H
P157A P157K
P157VP157W
This operation is only necessary if the operator opens the leaf instead of closing it when making a reset (rS).
P157X
I
II
P157E
Total opening radio code programming, P1 (with RSD receiver only, C801)
 I f a receiver other than
RSD is used, see the
corresponding
instructions.
Select the option C801
(RSD receiver) before
programming.
Pedestrian opening radio code programming, P2 (with RSD receiver only, C801)
This procedure is the same as for total opening, but using parameter P2 instead of P1.
OWait whilst the gate
carries out the
open/close
Open/close programming (P3)
I
II

10
Complete programming chart
D1 D2 Parameter D3 D4 Default
option Options or values
C1Motor turning direction 01x
02
4Opening safety device (photocell or strip) 00xDevice not installed
10 Device without testing
11 Device with testing
5Closing safety device (photocell or strip)
Closing photocell with C520 or C521, also
prevents the gate from opening
00xDevice not installed
10 Device without testing
11 Device with testing
20 Device without testing
21 Device with testing
8Radio receiver 01 RSD card (non-decoding)
02xTwin-channel decoding card
P1Total opening radio code programming oç
2Pedestrian opening radio code programming oç
3Gate open/close programming oç
F1Functioning mode 01 Automatic
02xStep-by-step
2Standby in automatic mode 0...5ÿ 0...915 59= 59 sec; 2ÿ5 = 2 min. 50 sec., etc
3Pedestrian opening 00xPedestrian opening is not carried out
10 10% of total opening
20 20% of total opening
30 30% of total opening
40 40% of total opening
50 50% of total opening
A0Flashing light 01xNo pre-warning
02 With pre-warning
1Garage light time 0...5ÿ 0...903 59= 59 sec; 2ÿ5 = 2 min. 50 sec., etc
2Gate speed 01...505 01: minimum speed; 05: maximum speed
3Slowdown speed 01...301 01: minimum speed; 05: maximum speed
4Slowdown distance 00...501 00: minimum distance;
05: maximum distance
5Reverse after closing (to offset the expansion
of the gate)
A50x: stops in selected position without
making contact
A51x: makes contact and reverses back to
the selected position
0...11...905 x1: no recede;
x9: maximum recede
6Maximum thrust 0...10...905 01: minimum thrust; 10: maximum thrust
7Closing photocell used during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
8Pushbutton operation during standby (in
automatic mode only)
01 Immediate close
02xRestart standby time
03 Has no effect
9Opening mode 01xOpening in accordance with the mode
selected in the main functions (F)
02 Collective opening (the control board
does not obey the key commands during
opening)
03 Step-by-step opening (the gate halts if a
key device is activated during opening.
The gate closes when operated again)
ç1Operations carried out XX Indicates the hundreds of cycles
completed (for example, 68 indicates
6,800 cycles completed)