fantastic furniture Eden Utility 5 Shelf User manual

Eden
Utility 5 Shelf
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity : 15kg/Shelf.
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
2 x Top/Base Panels (P1);
Left Side Panel (P2);
Right Side Panel (P3);
3 x Shelf Panels (P4);
Fixed Shelf Panel (P5);
2 x Back Panels (P6);
2 x Rails (P7);
2 x Back Panels (P8);
Hardware pack
Top/Base Panel
(P1)
Top/Base Panel
(P1)
Shelf Panel
(P4)
Shelf Panel
(P4)
Fixed Shelf Panel
(P5)
Shelf Panel
(P4)
Right Side
Panel (P3)
Left Side
Panel (P2)
Rail
(P7)
Rail
(P7)
Back
Panel
(P6)
Back
Panel
(P8)
Back
Panel
(P8)
Back
Panel
(P6)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
16 x Dowels
(H1)
12 x Screws
(H2)
16 x Cam
Bolts
(H3)
16 x Cam
Nuts
(H4)
12 x Shelf
Supports
(H5)
12 x Wedges
(H7)
4 x Plastic
Glides
(H6)
1 x Safety
Strap
Screw
(H9)
1 x Safety
Strap
(H8)
2 x Washers
(H10)

8 x Cam Bolts
(H3)
(P2)
(P3)
You will need
Step 1
Step 2
You will need
Attach 8 x Cam Bolts (H3) to Left Side Panel (P2) as shown by tightening with the
Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
Attach 8 x Cam Bolts (H3) to Right Side Panel (P3) as shown by tightening with the
Phillips Head Screwdriver.
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3

Slide Back Panels (P6 x 2 & P8 x 2) into the grooves
of Top/Base Panels (P1 x 2) and Fixed Shelf Panel (P5).
(P1)
(P1)
(P1)
(P1)
(P2)
(P7)
(P7)
(P5)
(P5)
(P6)
(P8)
(P8)
(P6)
fantasticfurniture.com.au Page 6
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 4
Step 3
You will need
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
Insert 8 x Dowels (H1) into
Left Side Panel (P2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P5) and Rails (P7 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P5) and Rails (P7 x 2) to Left Side Panel (P2)
by tightening all nuts with the Phillips Head Screwdriver.
H4
H4
H4
H1
H1
H1
Ensure laminated
side of panels are
facing inwards.

Step 5
You will need
You will need
Step 6
Secure 4 x Plastic Glides (H6) to the bottom of Left & Right Side Panels (P2 & P3)
as shown using the Hammer.
(P2)
(P1)
(P1)
(P7)
(P7)
(P3)
(P3)
(P5)
fantasticfurniture.com.au Page 7
Phillips Head
Screwdriver
Hammer
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
4 x Plastic
Glides (H11)
Insert 8 x Dowels (H1) into
Top/Base Panels (P1 x 2), Fixed Panel (P5)
and Rails (P7 x 2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P5) and Rails (P7 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Right Side Panel (P3) to Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P5) and Rails (P7 x 2) by tightening all nuts with the Phillips Head Screwdriver.
H4
H4
H4
H1
H1
H1
H6
H6
H6
H6

You will need
Step 7
Insert 12 x Shelf Supports (H5)
into the holes of the left & Right
Side Panels (P2 & P3) at your
preferred shelf height. Insert the
Shelf Panels (P4 x 3) into the unit
by resting each shelf on the Shelf
Supports. Ensure eash shelf is
positioned securely.
Secure Back Panels (P6 x 2 & P8 x 2) in place with 12 x Wedges (H7) using 12 x Wedge Screws
(H2) by tightening with the Phillips Head Screwdriver.
(P3)
(P3)
(P4)
(P4)
(P4)
(P2)
(P2)
(P6)
(P6)
(P8)
(P1)
(P8)
fantasticfurniture.com.au Page 8
H7
H2
H5
12 x Shelf
Supports (H5)
You will need
Step 8
Phillips Head
Screwdriver
12 x Wedges
(H7)
12 x Wedge
Screws (H2)
Align the Shelf Support
to the hole of Adjustable
Shelf Panel.
H5
(P4)

Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
H8
H8
H9
H9 H10
H10
fantasticfurniture.com.au Page 9
1 x Safety Strap
Screw (H9)
1 x Safety
Strap (H8)
1 x Washer
(H10)
Attach the Safety Strap (H8) to the
Top Panel (P1) with 1 x Safety Strap
Screw (H9) & 1 x Washer (H10) by tightening
with the Phillips Head Screwdriver.
H10
wall
Screw
Move the unit to the final position, and
attach the safety strap to the wall securely.
Make sure it is firmly attached and snug fit.
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
You will need
Step 10
Phillips Head
Screwdriver
1 x Washer
(H10)
Screw and Wall Plug
are not provided.
Please use appropriate
fixtures for your wall.
You will need
Step 9
Phillips Head
Screwdriver
(P3)
(P2)
(P1)
We strongly advise that you
use the wall safety strap
provided to prevent the unit
toppling.