fantastic furniture Elevate User manual

Electric Lift Desk
fantasticfurniture.com.au
Required
Two People
Version 1.0
Elevate

fantasticfurniture.com.au Page 2
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Make sure the unit is turned o and unplugged before cleaning.
Do not connect the power supply to a household power outlet with wet hands,
as it may cause fire, electric shock or injury to the person.
Do not operate this unit if the cord or plug is damaged, after a malfunction
or if it has been dropped or damaged in any manner.
For indoor use only.
WARNING:
Recommended weight capacity:
Up to 100KG in its lowest position and 45kg when raised.
Looks like you’ve found
your Fanstastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!

Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au Page 3

What you need
to assemble the product
fantasticfurniture.com.au
Page 4
Top Panel (P1)
Side Rail (P2)
Long Rail (P3)
Side Rail (P2)
Left Leg
(P5)
Right Leg
(P6)
Foot (P7)
Foot (P7)
SYNC Rod (P4)
Part list
Carton 1:
2 x Side Rails (P2)
1 x SYNC Rod (P4)
1 x Left Leg (P5)
1 x Right Leg (P6)
2 x Foot (P7)
1 x Hexagonal Shaft (P8)
Carton 2:
1 x Top Panel (P1)
1 x Long Rail (P3)
Other tools you need
Phillips Head Screwdriver
Hexagonal Shaft (P8)

fantasticfurniture.com.au
Page 5
Hardware Pack
8 x Bolts
20mm (H1)
4 x Bolts
25mm (H2)
20 x Bolts
12mm (H3)
3 x Bolts
52mm (H4)
2 x Screws
25mm (H5)
1 x Allen Key
4mm (H6)
1 x Allen Key
2mm (H7)
1 x Controler
(H8)
1 x Adapter
(H9)
4 x Adjustable Foot
(H10)
3 x Screws
12mm (H11)
3 x Cable Ties
(H12)
1 x Allen Key
6mm (H13)
2 x Bolts
3mm (H14)

Step 1
Page 6fantasticfurniture.com.au
You will need
Attach 2 x adjustable feet (H10) into foot (P7 x 2) as shown.
Step 2
You will need
8 x Bolts
20mm (H1)
Attach foot (P7 x 2) onto left & right legs (P5 & P6)
with 8 x bolts (H1) as shown, by tightening the bolts
with allen key (H6).
4 x Adjustable
Foot (H10)
X2
1 x Allen Key
4mm (H6)
(P7)
H10
H10
(P6)
(P5)
H1
H1
(P7)
(P7)

Step 3
Page 7fantasticfurniture.com.au
You will need
Attach long rail (P3) to left & right legs (P5 & P6) with 4 x bolts (H2) by tightening
with allen key (H6).
4 x Bolts
25mm (H2)
Required
Two People
(P3)
(P5)
(P6)
H2
H2
1 x Allen Key
4mm (H6)
H2
H2

Step 4
Page 8fantasticfurniture.com.au
You will need
1 x Allen Key
4mm (H6)
10 x Bolts
12mm (H3)
H3
H3
H3 H3
(P2)
(P2)
Attach side rails (P2 x 2) to the assembled frame with 10 x bolts (H3) by tightening
with allen key (H6).
H3
Note:
Press the leg all the way down.

Step 5
Page 9fantasticfurniture.com.au
You will need
Insert hexagonal shaft (P8) into SYNC rod (P4) as shown.
Mount the SYNC rod (P4) onto motor hexagonal shaft on right leg (P6) as shown.
Insert 1 x bolt (H14) into SYNC rod (P4) as shown, by tightening with allen key (H7).
Insert hexagonal shaft (P8) into the hexagonal hole on the left leg (P5).
if needed, use allen key (H13) to slightly adjust the angle of hexgonal hole on the left leg (P5)
anticlockwise, so that the hexagonal shaft (P8) can be inserted into the hole.
Insert 1 x bolt (H14) into SYNC rod (P4) as shown, by tightening with allen key (H7).
Check to be sure the left & right leg are aligned.
(P8)
1 x Allen Key
6mm (H13)
1 x Allen Key
2mm (H7)
(P4)
2 x Bolts
3mm (H14)
3
10mm
12
4
H7
H7
H14
H14
H13
(P6)
(P5)
(P4)
(P4)
(P5)
(P6)
(P4) (P8) (P5)

Step 6
Page 10fantasticfurniture.com.au
You will need
2 x Screws
28mm (H5)
Phillips Head
Screwdriver
1 x Controller
(H8)
H5
H8
Attach controller (H8) onto top panel (P1) with 2 x screws (H5) as shown, by tightening with
the phillips head screwdriver
H5
H5 H8

Step 7
Page 11fantasticfurniture.com.au
You will need
Attach the assembled frame onto the back of top panel (P1) as shown.
Secure side rails (P2 x 2) with 8 x bolts (H3), tighten with large allen key (H6).
Secure Long rail (P3) with 3 x bolts (H4) tightening with large allen key (H6).
Secure left & right legs (P5 & P6) wiht 2 x bolts (H3), tighten with large allen key (H6).
H4
1 x Large
Allen Key (H6)
10 x Bolts
12mm (H3)
3 x Bolts
40mm (H4)
(P1)
(P3)
(P2)
(P2)
(P5)
(P6)
H4
H4
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3

Step 8
Page 12fantasticfurniture.com.au
You will need
1 x Adaptor
(H9)
Peel O Sticker
1 3
Insert cable through the strap
Tighten the strap
2
Tighten Up
Screws (Optional)
Connect Power Cable
to controller (H8).
Interface
for Motor cable
H9
H11
H8
H8
H12
H9
(P1)
3 x Cable Ties
(H12)
Phillips Head
Screwdriver
3 x Screws
(H11)
Connect the adapter (H9), cotroller (H8) and motor together as shown.
We have provided 3 x cable tie organisers with this desk if you would like to use them.
Peel o the backing sticker. Stick on the underside of the desk as shown.
We have provided 3 pre-drilled holes as suggested locations.
You can choose to fix the cable ties with 3 x screws (H11), tightening with a phillips
head screwdriver.
Insert cable through the strap, and tighten the strap.

Step 9
Page 13fantasticfurniture.com.au
With assistance, carefully turn over desk upright and move the desk to the final position.
if need, rotating the adjust foot to make the desk level.
Required
Two People

Step 10
Page 14fantasticfurniture.com.au
Height Adjustment (Down)
Height Adjustment (Up)
Left button (Up)
1. Continuously hold the button to raise the table and release when it arrives
at the desired height.
2. The desk will stop automatically when it is raised to the highest position.
Right button
1. Continuously hold the button to lower the table and release when it arrives
at the desired height.
2.The desk will stop automatically when it is lowered to the lowest position.
+ Reset
1. Press and hold the up and down buttons at the same time for 3 seconds
until the desk automatically moves down. At this time you can release the buttons.
You will hear 4 beeps signalling that the Reset operation is complete.
OPERATION: N
Controller
TROUBLESHOOTING
1-time beep
2-time beep
3-time beep
4-time beep
Line voltage too low.
Motor temperature is too high
or has been in continuous
operation for more than
2 minutes.
There is too much weight
on the desktop or the motor
is overloaded.
Motor without electricity.
Electric system breakdown.
Replace power supply adapter.
Rest system for 18 minutes
before continuing to operate.
Decrease desk top max loading
under 45kg. Unplug the power cord
and re-plug after 1 minute,
perform RESET operation.
Check to see if the motor wire is
connected properly.
Unplug the power cord and re-plug
after 1 minute, perform RESET operation.
Unplug the power cord and re-plug
after 1 minute, perform RESET operation.
PROBLEM ROOT CAUSE CORRECTIVE ACTION

Step 11
Page 15
fantasticfurniture.com.au
Job complete!
In the interest of our environment please dispose
of all packaging thoughtfully.
Warning: After completing the installation, be sure to perform the “Reset” operation.