fantastic furniture Eden Utility 5 Drawer 2 Shelf User manual

Eden
Utility 5 Drawer 2 Shelf
fantasticfurniture.com.au
Version 1.0

fantasticfurniture.com.au
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
WARNING: ENSURE THE WALL STRAP IS ATTACHED TO
AVOID SERIOUS INJURY.
To avoid any serious or fatal injury, this product has been supplied
with a wall strap to prevent toppling. We strongly recommend that
this product is permanently fixed to the wall or other suitable sur-
face. Connecting attachments for your wall are not included since
dierent surface materials require dierent attachments. Please seek
professional advice if you are in doubt of what wall connections to
use.
Recommended weight capacity :
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture
Page 2
15kg/Drawer or Shelf.

Page 3
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
! The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
! Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
! If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
2 x Top/Base Panels (P1);
Left Side Panel (P2);
Right Side Panel (P3);
Shelf Panel (P4);
2 x Rails (P5);
Fixed Shelf Panel (P6);
2 x Back Panels (P7);
5 x Drawer Fronts (P8);
5 x Left Drawer Sides (P9);
5 x Right Drawer Sides (P10);
5 x Drawer Bases (P11)
5 x Drawer Backs (P12);
5 x Support Rails (P13)
2 x Back Panels (P14);
Hardware pack
Top/Base Panel
(P1)
Shelf Panel
(P4)
Fixed Shelf Panel
(P6)
Right Side
Panel (P3)
Left Side
Panel (P2)
Rail
(P5)
Rail
(P5)
Back
Panel
(P7)
Back
Panel
(P14)
Back
Panel
(P14)
Back
Panel
(P7)
Left
Drawer
Side (P9)
Drawer
Front (P8)
Right
Drawer
Side
(P10)
Drawer
Back (P12)
Drawer
Base (P11)
Top/Base Panel
(P1)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 4
fantasticfurniture.com.au
DO NOT USE
21 x Dowels
(H1)
30 x Long
Screws
(H2)
50 x Small
Screws
(H5)
16 x Cam
Bolts
(H3)
16 x Cam
Nuts
(H4)
4 x Shelf
Supports
(H10)
25 x Small Cam
Bolts
(H14)
25 x Small Cam
Nuts
(H15)
12 x Wedges
(H12)
4 x Plastic
Glides
(H11)
12 x Wedge
Screws
(H13)
1 x Safety
Strap
Screw
(H17)
1 x Safety
Strap
(H16)
2 x Washers
(H18)
5 x CL Runner
Tracks
(H6)
5 x CR Runner
Tracks
(H7)
5 x DL
Runners
(H8)
5 x DR
Runners
(H9)
x5
Support
Rail (P13)

15 x Small
Screws (H5)
15 x Small
Screws (H5)
8 x Cam Bolts
(H3)
(P2)
(P3)
You will need
Step 1
Step 2
You will need
Attach 8 x Cam Bolts (H3) to Left Side Panel (P2) as shown by tightening with the
Phillips Head Screwdriver. Attach 5 x CL Runner Tracks (H6) to Left Side Panel (P2) with
15 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 5
8 x Cam Bolts
(H3)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
Attach 8 x Cam Bolts (H3) to Right Side Panel (P3) as shown by tightening with the
Phillips Head Screwdriver. Attach 5 x CR Runner Tracks (H7) to Right Side Panel (P3)
with 15 x Small Screws (H5) by tightening with the Phillips Head Screwdriver.
H6
H6
H7
H5
H5
H5
H5
H5
H5
CL
H5
H3
H3
H3
H3
H3
H3
H3
H3
H3
H3
5 x CL Runner
Tracks (H6)
H7
CR
H5
5 x CR Runner
Tracks (H7)

Slide Back Panels (P7 x 2 & P14 x 2) into the grooves of
Top/Base Panels (P1 x 2) and Fixed Shelf Panel (P6).
Ensure laminated
side of panels are
facing inwards.
Ensure the grooves in the Top/Base
Panels (P1 x 2) and Fixed Shelf Panel (P6)
are located at the back of the unit.
Grooves for
back panels
(P2)
(P1)
(P1)
(P1)
(P1) (P5)
(P5)
(P6)
(P6)
(P7)
(P14)
(P14)
(P7)
fantasticfurniture.com.au Page 6
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
Step 4
Step 3
You will need
Phillips Head
Screwdriver
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
Insert 8 x Dowels (H1) into
Left Side Panel (P2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P6) and Rails (P5 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P6) and Rails (P5 x 2) to Left Side Panel (P2)
by tightening all nuts with the Phillips Head Screwdriver.
H1
H1
H1
H4
H4
H4

Step 5
You will need
You will need
Step 6
Secure 4 x Plastic Glides (H11) to the bottom of Left & Right Side Panels (P2 & P3)
as shown using the Hammer.
(P2)
(P1)
(P3)
(P3)
(P1)
(P6)
(P5)
(P5)
fantasticfurniture.com.au Page 7
Phillips Head
Screwdriver
Hammer
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
4 x Plastic
Glides (H11)
Insert 8 x Dowels (H1) into
Top/Base Panels (P1 x 2), Fixed Shelf Panel (P6)
and Rails (P5 x 2). Insert 8 x
Cam Nuts (H4) into Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P6) and Rails (P5 x 2). Rotate
the nuts so the arrows point towards the
incoming bolts. Attach Right Side Panel (P3) to Top/Base Panels (P1 x 2),
Fixed Shelf Panel (P6) and Rails (P5 x 2) by tightening all nuts with the Phillips Head Screwdriver.
H1
H1
H1
H4
H4
H4
H11
H11
H11
H11

You will need
Step 7
You will need
Step 8
Phillips Head
Screwdriver
H14
(P8)
(P2)
(P3)
(P4)
fantasticfurniture.com.au Page 8
Attach 5 x Small Cam Bolts (H14) to Drawer Front (P8) as shown by tightening with the
Phillips Head Screwdriver.
H10
H10
H14
H14
H14
H14
4 x Shelf
Supports (H10)
5 x Small Cam
Bolts (H14)
Align the Shelf Support
to the hole of Adjustable
Shelf Panel.
H10
(P4)
Insert 4 x Shelf Supports (H10)
into the holes of the Left & Right
Side Panels (P2 & P3) at your
preferred shelf height. Insert the
Shelf Panel (P4) into the unit
by resting on the Shelf Supports. Ensure the shelf is positioned securely.

You will need
Step 9
Phillips Head
Screwdriver
Step 10
Insert 1 x Dowel (H1) into Drawer Front (P8). Insert 5 x Small Cam Nuts (H15) into Left & Right
Drawer Sides (P9 & P10) and Support Rail (P13). Rotate the nuts so the arrows point towards
the incoming bolts. Attach the Left & Right Drawer Sides (P9 & P10) and Support Rail (P13) to
Drawer Front (P8) by tightening all nuts with the Phillips Head Screwdriver.
Slide Drawer Base (P11) into the grooves of Left &
Right Drawer Sides (P9 & P10) and Drawer Front (P8).
Ensure laminated
side of panel is
facing inwards.
H15
H1
(P13)
1 x Dowel
(H1)
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P8)
(P8)
(P9)
(P9)
(P10)
(P10)
(P11)
5 x Small Cam
Nuts (H15)
fantasticfurniture.com.au Page 9
H15
H15
H15
H15

You will need
Step 11
Attach Drawer Back (P12) to Left & Right Drawer Sides (P9 & P10) and Support Rail (P13) with
6 x Long Screws (H2) by tightening with the Phillips Head Screwdriver. Ensure the drawer base
lines up with the grooves all the way around the drawer before securing.
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P9 ) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P10) with 4 x Small Screws (H5) by tightening with the
Phillips Head Screwdriver.
Repeat Step 8 - 12 for the remaining 4 x Drawers.
Phillips Head
Screwdriver
You will need
Step 12
Phillips Head
Screwdriver
(P9)
(P9)
(P10)
(P10)
(P12)
fantasticfurniture.com.au Page 10
H2
H2
H2
H5
H5
H5
H8
H9
H5
H2
4 x Small
Screws (H5)
1 x DL Runner
(H8)
1 x DR Runner
(H9)
6 x Long
Screws (H2)
H2 H2