fantastic furniture Como 2.0 User manual

Como 2.0
Bedside 2 Drawer
fantasticfurniture.com.au
Version 1.0

Secure it!
Wall attachment guide
(with available wood stud)
Screw directly into
stud.
Please seek professional advice if you are in doubt of what fixing device to use.
•
•
• Do not
•
•
Reduce the risk of furniture
tip-over accidents
(with available wood stud)
S
.
Screw
fantasticfurniture.com.aufantasticfurniture.com.au
Recommended Weight Capacity :10kg/Drawer

fantasticfurniture.com.au Page 3
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love!
Love it? Share it!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasticfurniture

Page 4
Read through the instructions carefully
before you begin.
Assembly Checklist
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screws until the item is fully assembled.
!Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
!Always use a soft surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
!Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
!Never use any glue until you are certain that the parts belong together.
!Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
!If you are having any diculties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
!Please see page 2 for any safety requirements or weight restrictions.
Make sure you have all the required tools.
Never use power tools unless instructed.
Useful Information
fantasticfurniture.com.au

Parts list
Top Panel (P1);
Bottom Panel (P2)
Left Side Panel (P3);
Right Side Panel (P4);
Back Panel (P5);
Rail (P6);
Rail (P7);
2 x Rail (P8);
2 x Rail (P9);
Drawer Front (P10);
Left Drawer Side (P11);
Right Drawer Side (P12);
Drawer Back (P13);
2 x Drawer Bases (P14);
Drawer Front (P15);
Left Drawer Side (P16);
Right Drawer Side (P17);
Drawer Back (P18);
Hardware pack
1 x Safety
Strap
(H13)
2 x Washers
(H14)
What you need
to assemble the product
Other tools you need:
Phillips head screwdriver;
Hammer
Page 5
fantasticfurniture.com.au
DO NOT USE
Top Panel
(P1)
Right Side
Panel
(P4)
Left Drawer
Side (P11)
Left Drawer
Side (P16)
Drawer Front
(P10)
Drawer Front
(P15)
Right Drawer
Side (P12)
Right Drawer
Side (P17)
Drawer Back
(P13)
Drawer Back
(P18)
Drawer Base
(P14) Drawer Base
(P14)
Left Side
Panel
(P3)
Rail
(P6)
Rail
(P7)
Rail
(P8)
Rail
(P9) Rail
(P8)
Rail
(P9)
Bottom Panel
(P2)
Back Panel
(P5)
20 x Dowels
(H1)
7 x Long Screws
(H2)
24 x Small Screws
(H5)
2 x CL Runner
Tracks
(H6)
26 x Cam Bolts
(H3)
26 x Cam Nuts
(H4)
2 x CR Runner
Tracks
(H7)
2 x DL Runners
(H8)
2 x DR Runners
(H9)
8 x Screws
(H10)
12 x Screws
(H12)
4 x Plastic
Glides
(H11)

You will need
Step 3
Attach 4 x Cam Bolts (H3) to the Left Side Panel (P3). Tighten with a Phillips Head Screwdriver.
6 x Small
Screws (H5)
H6
H5
H5
H5
H5
H5
H5
H5 H7
H7
H5
H5
H5
H5
H5
H3
H3 H3
H3
H6
H7
CR
H5
You will need
Step 1
Step 2
You will need
Phillips Head
Screwdriver
Attach 2 x CL Runner Tracks (H6) to the Left Side Panel (P3) using 6 x Small Screws (H5),
tightening with the Phillips Head Screwdriver.
Attach 2 x CR Runner Tracks (H7) to the Right Side Panel (P4) using 6 x Small
Screws (H5), tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 6
2 x CL Runner
Tracks (H6)
H6
CL
H5
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
(P3)
(P3)
(P4)
6 x Small
Screws (H5)
Phillips Head
Screwdriver
2 x CR Runner
Tracks (H7)

Step 5
You will need
Attach 4 x Cam Bolts (H3) to the Right Side Panel (P4). Tighten with a Phillips Head Screwdriver.
2 x Dowels
(H1)
3 x Long
Screws (H2)
Phillips Head
Screwdriver
Step 4
You will need
H1
H1
H13
H13
H14
H14
H2
H2
H2
H3
H3
H3
H3
Insert 2 x Dowels (H1) into Top Panel (P1). Attach Rail (P6) to Top Panel (P1) with 2 x
Long Screws (H2). Tighten with a Phillips Head Screwdriver.
1 x Safety
Strap (H13)
1 x Washer
(H14)
Use 1 x Long Screw (H2) and 1 x Washer (H14) to secure the Safety Strap (H13) to the Top
Panel (P1) through the pre-cut hole in the Rail (P6).
fantasticfurniture.com.au
fantasticfurniture.com.au Page 7
L
(P4)
(P1)
(P6)
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)

1 x Cam Nut
(H4)
You will need
Step 6
H1
H1
H4
H1
H1
H1
H4
H4
H4
(P1)
(P6)
(P3)
Insert 4 x Dowels (H1) into the Left Side Panel (P3).
Insert 3x Cam Nuts (H4) into the Top Panel (P1) and
Rail (P6).
Secure the Top Panel (P1) and Rail (P6) to the Left Side
Panel (P3) by rotating the Cam Nuts (H4) so the arrows
point towards the incoming Cam Bolts (H3). Once in place,
tighten with the Phillips Head Screwdriver.
Insert 1 x Dowel (H1) into the Left Side Panel (P3).
Insert 1 x Cam Nut (H4) into the Rail (P7).
Secure the Rail (P7) to the Left Side Panel (P3)
by rotating the Cam Nut (H4) so the arrows point
towards the incoming Cam Bolt.
Once in place tighten with the Phillips Head Screwdriver.
This is how a cam nut works........
The head of the cam
bolt goes into the
open mouth of the
cam nut. You then
turn the cam nut so
it tightens over the
bolt.
fantasticfurniture.com.au Page 8
You will need
Step 7
1 x Dowel
(H1)
Phillips Head
Screwdriver
3 x Cam Nuts
(H4)
4 x Dowels
(H1)
Phillips Head
Screwdriver
(P7)
(P3)

H4
H4
H1
H1
H1 H1
H1
(P1)
(P6)
(P4)
(P6)
(P7)
(P7)
(P1)
You will need
Step 9
You will need
Step 8
Insert 5 x Dowels (H1) into the Top Panel (P1) and Rails (P6, P7) as shown.
Insert 4 x Cam Nuts (H4) into the Top Panel (P1) and
Rails (P6, P7) as shown.
Secure the Right Side Panel (P4) to the Top Panel (P1) and Rails (P6, P7)
by rotating the Cam Nut (H4) so the arrows point towards the incoming Cam Bolts.
Once in place tighten with the Phillips Head Screwdriver.
4 x Cam Nuts
(H4)
Phillips Head
Screwdriver
fantasticfurniture.com.au Page 9
5 x Dowels
(H1)

You will need
Step 11
You will need
Step 10
Phillips Head
Screwdriver
6 x Cam
Bolts (H3)
H3
H3
H3
H3
H3
H3
H1
H1
H2
H2
H2
H2
H1
Attach 6 x Cam Bolts (H3) to the Bottom Panel (P2). Tighten with a Phillips Head Screwdriver.
Insert 4 x Dowels (H1) into the Left Side Panel (P3) and Right Side Panel (P4) as shown.
Secure the Bottom Panel (P2) to the Left Side Panel (P3) and Right Side Panel (P4) with
4 x Long Screws (H2), tightening with the Phillips Head Screwdriver.
fantasticfurniture.com.au Page 10
(P2)
(P2)
(P3)
(P4)
4 x Dowels
(H1)
4 x Long
Screws (H2)
Phillips Head
Screwdriver

H4
H4
H4
H4
You will need
Step 13
You will need
Step 12
4 x Cam Bolts
(H3)
H3
H3
H1
H4
H4
H4
H4
H1
H1
H1
4 x Cam Nuts
(H4)
4 x Dowels
(H1)
Phillips Head
Screwdriver
Insert 4 x Cam Bolts (H3) into 2 x Rails (P8).
Insert 4 x Cam Nuts (H4) and 4 x Dowels (H1) into 2 x Rails (P9) as shown.
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts.
Secure 2 x Rails (P8) and 2 x Rails (P9) together, once in place tighten all
Cam Nuts with a Phillips Head Screwdriver.
Insert 6 x Cam Nuts (H4) into the Rails (P8, P9) as shown.
Secure the Rails (P8, P9) to the Bottom Panel (P2) by rotating the Cam Nuts so
the arrows point towards the incoming Cam Bolts, once in place tighten with a
Phillips Head Screwdriver.
fantasticfurniture.com.au Page 11
x2
(P8)
(P8)
(P8)
(P9)
(P9)
(P2)
(P8)
(P8)
(P9)
(P9)
6 x Cam Nuts
(H4)
Phillips Head
Screwdriver

You will need
Step 15
You will need
Step 14
12 x Screws
(H12)
4 x Plastic
Glides (H11)
H11
H11
H11
H11
H11
H12
H12
H12
H12
Hammer
Attach the Back Panel (P5) to the Left Side Panel (P3), Right Side Panel (P4), Rail (P6) and
Bottom Panel (P2) with 12 x Screws (H12) .Tighten with a Phillips Head Screwdriver.
Secure 4 x Plastic Glides (H11) to the Rails (P8, P9) as shown using a hammer.
fantasticfurniture.com.au Page 12
Phillips Head
Screwdriver
(P4)
(P5)
(P6) (P3)
(P2)
(P8)
(P8) (P9)
(P9)

Step 16 H3 H3
H3 H3
H4
H4
H4H4
Insert 4 x Cam Nuts (H4) into the holes of Drawer
Sides (P11, P12). Rotate the cam nuts so the arrows
point towards the incoming cam bolts, secure the
Drawer Sides (P11, P12) to the Drawer Front (P10) and tighten with a Phillips Head Screwdriver.
fantasticfurniture.com.au Page 13
You will need
Step 17
Step 18
(P12)
(P10)
(P12)
(P11)
(P14)
(P11)
(P10)
You will need
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
4 x Cam
Nuts (H4)
Phillips Head
Screwdriver
Attach 4 x Cam Bolts (H3) to the Drawer Front (P10). Tighten with a Phillips Head Screwdriver.
Slide Drawer Base (P14) into the groove in Drawer Sides (P11, P12).

Step 19
H3
H3
H3
H3
H10
H10
H10
H10
H5
H8
H9
H5
H5
H5
H5
H5
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P11) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P12) with 6 x Small Screws (H5).Tighten with a Phillips
Head Screwdriver.
(P12)
(P15)
(P11)
(P13)
(P11)
(P12)
fantasticfurniture.com.au Page 14
You will need
Step 20
You will need
Step 21
You will need
Phillips Head
Screwdriver
4 x Screws
(H10)
Phillips Head
Screwdriver
4 x Cam
Bolts (H3)
6 x Small
Screws (H5)
1 x DL Runner
(H8)
1 x DR Runner
(H9)
Phillips head
screwdriver
Attach 4 x Cam Bolts (H3) to the Drawer Front (P15).
Tighten with a Phillips Head Screwdriver.
Attach Drawer Back (P13) to Drawer Sides (P11, P12) with 4 x Screws (H10), make sure
that the groove lines up the whole way around the drawer.
H8
H9

Step 22
H4
H4
H4
H4
H10
H10
H10
H10
Insert 4 x Cam Nuts (H4) into the holes of Drawer
Sides (P16, P17). Rotate the cam nuts so the arrows
point towards the incoming cam bolts, secure the Drawer
Sides (P16, P17) to the Drawer Front (P15) and tighten with a Phillips Head Screwdriver.
(P15)
(P17)
(P17)
(P17)
(P18)
(P15)
(P15)
(P16)
(P16)
(P14)
(P16)
fantasticfurniture.com.au Page 15
Step 23
You will need
Step 24
You will need
4 x Cam
Nuts (H4)
Phillips Head
Screwdriver
Phillips Head
Screwdriver
4 x Screws
(H10)
Slide Drawer Base (P14) into the groove in Drawer Sides (P16, P17).
Attach Drawer Back (P18) to Drawer Sides (P16, P17) with 4 x Screws (H10), make sure
that the groove lines up the whole way around the drawer.

Step 25
H5
H8
H8
H9
H9
H5
H5
H5
H5
H5
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P16) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P17) with 6 x Small Screws (H5). Tighten with a Phillips
Head Screwdriver.
fantasticfurniture.com.au Page 16
You will need
Step 26
(P15)
(P16)
(P10)
(P15)
(P17)
6 x Small
Screws (H5)
1 x DL Runner
(H8)
1 x DR Runner
(H9)
Phillips head
screwdriver
Carefully insert the drawers into the unit as shown
by gently guiding the runners into the tracks.

H14 H14
Move the bedside to its final position. Attach the safety strap to the wall. Make sure it is firmly
attached and make sure it is a snug fit.
Seek advice from a qualified
trades person on how to
attach this safety strap to
your specific wall.
fantasticfurniture.com.au Page 17
You will need
Step 27 wall
Screw
Phillips head
screwdriver
1 x Washer
(H14)
Screw and Wall Plug are not
provided. Please use
appropriate fixtures for
your wall.
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.