fantastic furniture BINGO Bed Single User manual

BINGO
Bed Single
Assembly Instructions
Ver1.2

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose.When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

What you Need
To Assemble the Body
Please make sure you have all these parts before you start.
14
x Long
Bolts
(H1)
Page 3
2 x Bed Foot Legs
(P2) 1x Side Rails
(P4)
2 x Bed Head Legs
(P1)
1 x Side Rails
(P5)
1x Side Rails
(P5)
1x Side Rails
(P4)
1x Support legs
(P6)
1 x Centre Rail
(P7)
5 x Bed Head&Foot Connect Bar
(P3)
22 x Bed Base Slats
(P8)
(H2) (H3)
8 x M8
(H6)
4 x M8 Hex Nuts
(H4)
8
x Medium
Bolts 4
x Small
Bolts 4 x M6 Hex Nuts
(H5)
10 x M6
(H7)
1 x Allen Key
(H8)
1 x Spanner
(H9)

Step 1
You will need
10 x Long Bolts
(H1)
Step 2
You will need
(H1)
Insert 10 x Bolts (H1) and 10x Washer (H7) into the holes in Bed Head (P1) and Bed Foot (P2) to connect cross
rails P3 using
Allen Key provided. Do not fully tighten Bolts.
Attach Side Rails (P4&P5) to the Bed Head (P1) and Bed
Foot (P2) with Bolt (H2) and Washers (H6),
you also need 4 x Hex Nuts ( H4). Please pay attention to the Side Rails (P4&P5 are opposite).
Use 4 x Bolts (H1) to attach Support Legs (P6) with Side Rails( P4&P5). Do not fully tighten all Bolts.
1 x Allen key
1 x Allen key
Page 4
4 x Long Bolts
8 x Medium Bolts
(H2)
1 x Spanner
(H1)
(H7)
(P1)
(P2)
(P3)
(P1)
(P2)
(P3)
(P3)
(P3)
(P3)
(P4)
(P4)
(P5)
(P5)
(P6)
(P6)
(H2)
(H6)
(H1)
(H5)
(H4)
10 x M6
(H7)
4 x M8
Hex Nuts
(H4)
4 x M6
Hex Nuts
(H5)
4 x M8
(H6)
Bed Foot (P2)
Bed Head (P1)

Step 3
You will need
4 x Small Bolts
(H3)
Step 4
Attach 4 x Bolts (H3) to connected Side Rails. With the Allen Key provided. Tighten all the Bolts.
Put 22 x Bed Base Slats on their correct place and then insert them one after one.
IMPORTANT: Ensure all Bolts and Hex Nuts are fully tighten. Periodically check to ensure all bolts are tight.
1 x Allen key
Page 5
(P7)
(H3)
(P8)
(P8)
(P8)