fantastic furniture VOGUE User manual

Assembly Instructions
VOGUE
HALL TABLE
Tempered glass should always be handled with care.
Ver.1.1

Page 2
2
3
56
Read Instructions carefully.
Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
WARNING
WARNING
Check no parts are missing.
4
fully tighten screws（leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

4 x Tube
Screws
(H1)
4x Pads
(H2) 4x Glass clamps
(H4)
(tools not provided)
Phillips Head Srewdriver
What You Need
Page 3
1 x allen key
(H5)
(P2)
(P1)
(P2)
4x Dowels
(H3)
Please make sure you have all these parts before you start.
side panel
side panel
top panel
(P3)
shelf glass
1x Screw
(H6)
1x Wall
strap
(H7)
1x Washer
(H8)
1 x allen key
(H5)
4x Screw
(H9)

Glass clamps
H4
H4
H4
H4
H3
H3
H3
H3
H3
Attach 2 X Dowels(H3) and
2 X Glass clamps(H4) to each
side panel (P2)
Put the side panel (P2) and
the top panel (P1) together.
Make sure the plastic pad
of the grub screw is going inside
the Glass clamp(H4) and that all
the clamps are facing with the grub
screw towards to the bottom (longer end)
4x Screw
(H9)
(H9)
(H4)

Step 3
Page 5
Step 4
You will need:
4xPads
(H2)
You will need:
4x Tube
Screws
(H1)
(H1)
(H1)
(H2)
allen key
(H5)
(H5)
(H1)
(H1)
(H5)
(H1)
(H2)
(H2)
(H2)
(H2)
Attach 4X Tube screws(H1) to fix
the side panel and top panel and
use allen key(H5) to tighten the screws.
(P3)
Put the Pad(H2) on the right
position and insert the
shelf glass(P3).

Page 6
Step 5
Put the shelf glass on the right position
use the phillips head screwdriver to tighten
the screw and make the glass unmovable .
Don’t overtighten to avoid unwanted stress
on the glass panel which might cause it to
break during use.
Make sure the edge of the glass shelf is fully slot into
the clamp before tightening the grub screw.

Page 7
Turn over carefully.
Step 6
Step 7
You will need:
1x Screw
(H6)
1x Wall
strap
(H7)
1x Washer
(H8)
Use the screw (H5) and washer (H7) to connect the safety
strap(H6) on the top panel
We strongly advise that you use the wall strap
Provided to prevent the unit toppling.
(H8)
(H6)
(H7)

The job is now complete!
In the interest of our environment
Please dispose of all packaging thoughtfully
.
Page 8
Screws and wall plugs are not
provided
Please use appropriate fixtures
for your wall
Move the table to the final position. Attach the safety strap to the wall.
Make sure it is firmly attached and make sure it is a snug fit .
Step 8
This product should be checked periodically to ensure that all components are secure
and in the correct position and all connectors are tight.

TEMPERED GLASS should be handled with care.
Scratches, chips, sudden changes in temperature
and hairline fractures may cause the glass to break.
This glass is designed to break into small, relatively
harmless pieces and not sharp fragments.
Good to know
- Never place extremely hot or cold objects directly
onto the glass surface.
This may weaken the integrity of the glass and cause it to
break suddenly and without warning.
- Dropping heavy, glass, ceramic, metal or similar objects
on the table may cause unseen damage to the table leading
it to break suddenly and without warning.
TEMPERED GLASS WARNING