fantastic furniture COMO Queen Bed User manual

Assembly Instructions
Queen Bed
COMO
VER 1.2

Page 2
2
3
56
Read Instructions carefully. Lay out all of the components on a soft surface
as if you were preparing to do a jigsaw puzzle.
Carefully identify each component, especially
those that are similar. The most common mistake
is getting things back to front.
Separate and identify each component from the
hardware pack and rest each one in its proper
W
A
R
N
N
G
WARNING
Check no parts are missing.
4
fully tighten screws (leave slightly
loose).When the item is fully assembled
tighten the screws - but do not over tighten.
FAILURE TO FOLLOW THESE BASIC STEPS CAN LEAD TO DAMAGE
THAT IS NOT COVERED BY YOUR WARRANTY
If glue is required DO NOT set until you are
certain that the parts belong together.

Page 3
What You Need
To Assemble The Body
(Tools not provided)
Flat BladeScrewdriver
Phillips Head Screwdriver
Mallet
46 x Small
Dowels
(H2)
4 x Inside
Hexagonal
Screws
(H1)
24 x Screws
(Ø4 x 25)
(H5)
32 x Small
Screws
(Ø3.5 x 12)
(H14)
16 x Wheels
(H15)
20 x Small
Cam Nuts
(H9)
20 x Small
Cam Bolts
(H8)
Please make sure you have all these parts before you start.
40 x Screws
(Ø4 x 30)
(H6)
7 x Long
Screws
(Ø4 x 35)
(H7)
11 x Plastic
Glides
(H13)
4 x Elbow
Connectors
(H11)
4 x Flat
Connectors
(H12)
12 x Bolts
(H10)
Left Drawer
Side (P9)
Drawer
Front (P8)
x 4
Right
Drawer
Side
(P10)
Drawer Back
(P12)
Drawer
Base
(P11)
Central Drawer
Support
(P13)
2 x Drawer
Supports
(P14)
2 x Cam
Bolts
(H3)
2 x Cam
Nuts
(H4)
Bedfoot
(P2)
Bedhead
(P1)
Supporter
(P15)
Side Rail
(P3)
Side Rail
(P3)
Rail
(P4)
Rail
(P4)
Clapboard
(P7)
Support Leg
(P6)
Support Leg
(P6)
Central Rail
(P5)
1 x Allen Key
(Large)
(H17)
Block
(P16) Block
(P16)
Block
(P16) Block
(P16)
Supporter
(P15)
1 x Allen Key
(Medium)
(H18)
2 x Stickers
(H16)
28 x End Connectors 14 x Centre Connectors 28 x Fantastic Furniture
ComfortSlats Queen
TM

Step 2
You will need:
8 x Screws
(H6)
2 x Flat
Connetors
(H12)
3 x Plastic
Glides
(H13)
2 x Long
Screws
(H7)
Attach 2 x Flat Connectors (H12) to Bedhead (P1) with 8 x Screws (H6).
Attach Supporter (P15) to Bedhead (P1) with 2 x Long Screws (H7).
Then hammer 3 x Plastic Glides (H13) on the bottom of Bedhead (P1).
Step 1
You will need:
16 x Screws
(H5)
Attach 1 x Cam Bolt (H3) to Side Rail (P3).
Attach 2 x Elbow Connectors (H11) to Side Rail (P3) with 8 x Screws (H5).
Repeat Step 1 again with the other Side Rail (P3).
4 x Elbow
Connectors
(H11)
2 x Cam Bolts
(H3)
Page 4
H3
H5
(P2)
H5
H5
H5
H5
H11
H11
(P3)
Make sure the bottom of the “U” shape
is facing to the bottom rough side
of Bedhead (P1).
(P1)
(P15)
H6 H6
H13
H13
H13
H7
H7
H6H6
H12
H12

Step 3
You will need:
8 x Screws
(H6)
2 x Flat
Connetors
(H12)
3 x Plastic
Glides
(H13)
2 x Long
Screws
(H7)
Attach 2 x Flat Connectors (H12) to Bedfoot (P2) with 8 x Screws (H6).
Attach Supporter (P15) to Bedfoot (P2) with 2 x Long Screws (H7).
Then hammer 3 x Plastic Glides (H13) on the bottom of Bedfoot (P2).
Page 5
(P7)
2 x Cam Nuts
(H4)
You will need:
Step 4
2 x Small
Dowels
(H2)
Insert 2 x Small Dowels (H2) into Side Rails (P3).
Insert 2 x Cam Nuts (H4) into the holes of Clapboard (P7).
Rotate the cam nuts so the arrow point towards the incoming cam bolts.
Push Side Rails (P3) into place and tighten the cam nuts.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P3)
(P3)
H2
H4
Make sure the bottom of the “U” shape is
facing to the bottom rough side of Bedfoot (P2).
(P2)
(P15)
H6 H6
H13
H13
H13
H7
H7
H6 H6
H12
H12

Page 6
Step 5
You will need:
H13
H13
H13
(P2)
(P3)
(P3)
2 x Long Screws
(H7)
You will need:
6 x Bolts
(H10)
Step 6
4 x Small
Dowels
(H2)
H2
H2
H10
Insert 4 x Small Dowels (H2) into the holes of Bedfoot (P2).
Attach Side Rails (P3) to Bedfoot (P2) with 6 x Bolts (H10) using Allen Key (H17).
Do not fully tighten bolts, leave a little loose at this stage.
Attach Rails (P4) to Clapboard (P7) with 2 x Long Screws (H7).
Then hammer 3 x Plastic Glides (H13) on the bottom of Clapboard (P7).
MAKE SURE
TWO ENDS ALIGN
(P4)
(P4)
(P7)
H17
H7
H7
1 x Allen Key
(Large)
(H17)
3 x Plastic
Glides
(H13)

(P3)
(P3)
(P1)
Page 7
Step 8
4 x Small
Dowels
(H2)
H17
8 x Screws
(H5)
(P6)
(P16)
(P16)
(P16)
(P16)
(P4)
H5
H5
H5
H5 H5
H5
H5
H5 H5
H5
You will need:
Attach 4 x Blocks (P16) to Rails (P4) with 8 x Screws (H5).
A
A
SECTION A-A
H2
H2
H10
H10
Step 7
You will need:
6 x Bolts
(H10)
1 x Allen Key
(Large)
(H17)
Insert 4 x Small Dowels (H2) into the holes of Bedhead (P1).
Attach Side Rails (P3) to Bedhead (P1) with 6 x Bolts (H10) using Allen Key (H17). Tighten firmly.
Move the bed to final position then check and tighten all bolts attaching the Side Rails
to the Bedhead and Bedfoot.
2 PEOPLE CAREFULLY
TURN OVER THE BED FRAME

H13
H13
Page 8
Step 9
You will need:
Step 10
You will need:
(P6)
(P6)
(P5)
(P5)
(P7)
(P1)
(P2)
H7
H16
H16
H1
H18
H1
Attach 2 x Support Legs (P6) to Central Rail (P5), until it is firmly attached.
Then hammer 2 x Plastic Glides (H13) on Support Legs (P6).
Put Central Rail (P5) into the right place as shown.
Attach Central Rail to Bedhead (P1) and Beadfoot (P2) with 4 x Inside Hexagonal Screws (H1)
using Allen Key (H18) and Clapboard (P7) with 1 x Long Screw (H7).
Attach 2 x Stickers (H16) to the holes of Rails (P4).
2 x Plastic
Glides
(H13)
1 x Long Screws
(H7)
4 x Inside
Hexagonal
Screws
(H1)
2 x Stickers
(H16)
1 x Allen Key
(Medium)
(H18)

H8
H8
H9 H9
H9
H9
H9
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
5 x Small
Dowels
(H2)
Page 9
Step 11
You will need:
5 x Small Cam
Bolts
(H8)
Step 13
You will need:
(P8)
(P14)
(P8)
(P9)
(P13)
(P14)
(P14)
(P10)
Insert 5 x Small Dowels (H2) into Drawer Front (P8), and attach 5 x Small Cam Bolts (H8) to it.
Attach 2 x Wheels (H15) to Drawer Support (P14) with 4 x Small Screws (H14).
Repeat Step 12 again with the other Drawer Support (P14).
5 x Small Cam
Nuts
(H9)
Insert 5 x Small Cam Nuts (H9) into the holes of Drawer Sides (P9,P10)
and Central Drawer Support (P13).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push Drawer Sides (P9,P10) and
Drawer Supports (P13、P14)
into place and tighten the cam nuts.
Step 12
You will need:
H8
H15
H14
H14
H15
H14
H14
H8
H8
H2
H2
H2
4 x Wheels
(H15)
8 x Small
Screws
(H14)
(P9) (P10)
Grooves should
face inside.

Page 10
Step 14
Step 16
(P11)
(P12)
(P9)
(P9)
(P10)
(P10)
Slide Drawer Base (P11) into the groove in the middle of Drawer Sides (P9,P10).
Insert 4 x Small Dowels (H2) into 2 x Drawer Supports (P14).
Step 15
You will need:
6 x Screws
(H6)
H6
H6
H6
H6
Repeat step 11 to step 15 to assemble other 3 drawers.
H6
H6
Attach Drawer Sides (P9,P10) to Drawer Back (P12) with 4 x Screws (H6),
then attach Drawer Back (P12) to Central Drawer Support (P13) with 2 x Screws (H6).
Make sure that the groove lines up the whole way around the drawer.
4 x Small
Dowels
(H2)
You will need:
H2 H2
H2 H2