fantastic furniture COMO TV Stand User manual

COMO
TV Stand
www.fantasticfurniture.com.au
Version 1.0

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never ues any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk bed should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (sucn as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

16 x Dowels
(H1)
24 x Cam Bolts
(H2)
24 x Cam Nuts
(H3)
Top Panel
(P1)
Shelf Panel
(P2)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Divider
(P5)
Shelf Panel
(P2)
Left
Side Panel
(P3)
Left
Side Panel
(P3)
Right
Side Panel
(P4)
Right
Side Panel
(P4)
What you need
to assemble the product
Other tools you need
Flat head screwdriver; Phillips head
screwdriver; Hammer;
Parts list
Box 1: Top Panel (P1);
Shelf Panel (P2); Left Side Panel (P3);
Right Side Panel (P4);
Divider (P5);
www.fantasticfurniture.com.au PAGE 4
DO NOT USE
8 x Plastic Glides
(H4)
1 x Support Leg
(H5)
1 x Screw
(H6)

(P4) x 2
(P3) x 2
(P1)
H2 H2
Attach 8 x Cam Bolts (H2) into Top Panel (P1).
Tighten Cam Bolts using a Phillips head screwdriver.
Attach 8 x Cam Bolts (H2) into Left Side Panel (P3) and Right Side Panel (P4)
using a Phillips head screwdriver.
Repeat Step 2 for another Left Side Panel (P3) and Right Side Panel (P4).
8 x Cam Bolts
(H2)
You will need
Step 1
Phillips head
screwdriver
16 x Cam Bolts
(H2)
You will need
Step 2
Phillips head
screwdriver
www.fantasticfurniture.com.au PAGE 5
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2
H2

This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
Insert 4 x Dowels (H1) into Side Panels (P3, P4).
Put Dividers (P5) to the place as shown.
Insert 4 x Cam Nuts (H3) into the holes of Shelf Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P3, P4) to Shelf Panel (P2),
then tighten the cam nuts using a Flat head screwdriver.
H3
H3
H1
H1
H1
H1
(P4)
(P3)
(P4)
(P3)
(P2)
(P5)
(P5)
www.fantasticfurniture.com.au PAGE 6
You will need
Step 3
4 x Cam Nuts
(H3)
Flat head
screwdriver
You will need
Step 4
4 x Dowels
(H1)
H3
H3

Insert 4 x Dowels (H1) into Side Panels (P3, P4).
Put Dividers (P5) to the place as shown.
Insert 4 x Cam Nuts (H3) into the holes of Shelf Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P3, P4) to Shelf Panel (P2),
then tighten the cam nuts using a Flat head screwdriver.
H1 H1
H1 H1
(P4)
(P3)
(P4)
(P3)
(P2)
(P5)
(P5)
www.fantasticfurniture.com.au PAGE 7
4 x Cam Nuts
(H3)
Flat head
screwdriver
You will need
Step 6
4 x Dowels
(H1)
You will need
Step 5
H3
H3
H3
H3

Insert 8 x Dowels (H1) into Dividers (P5).
Insert 8
x Cam Nuts (H3) into the holes of Shelf Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Side Panels (P3, P4) to Shelf Panels (P2),
then tighten the cam nuts using a Flat head screwdriver.
Hammer 8 x Plastic Glides (H4) on to end of Shelf Panels (P3, P4).
Attach 1 x Support Leg (H5) to the bottom of Shelf Panel (P2) with 1 x Screw (H6).
H1
H3
H3 H3
H3
H1
H1 H1
H1
(P4)
(P3)
(P2)
(P5)
(P5)
www.fantasticfurniture.com.au PAGE 8
Phillips head
screwdriver
You will need
Step 7
8 x Cam Nuts
(H3)
8 x Dowels
(H1)
Flat head
screwdriver
1 x Support Leg
(H5)
1 x Screw
(H6)
You will need
Step 8
8 x Plastic
Glides (H4)
Hammer
(P4)
(P4)
(P3)
(P3)
H4 H4
H4 H4
H4 H4
H5
H6
H4 H4

H3
H3
(P1)
Insert 8 x Cam Nuts (H3) into the holes of Side Panels (P3, P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts using a Flat head screwdriver.
(P4)
(P4)
(P3)
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
www.fantasticfurniture.com.au PAGE 9
You will need
Step 9
8 x Cam Nuts
(H3)
Flat head
screwdriver
Recommended weight capacity : 80KG.