fantastic furniture HAVANA User manual

HAVANA
Coffee Table Rectangle
www.fantasticfurniture.com.au
Version 1.1

Enjoy
Your purchase from
Australia’s Best Value Furniture Store
www.fantasticfurniture.com.au PAGE 2

Assembly checklist
Useful Information
www.fantasticfurniture.com.au PAGE 3
Read through the instructions carefully
before you begin.
Identify and lay out all of the components
before you begin assembly.
! Never use power tools unless specifically instructed. They can damage your components or
hardware if used incorrectly.
! If you are having any difficulties assembling your product, missing any hardware or
components please visit our website Help Centre for further assistance.
! Periodically check and re-tighten all fasteners. Check the product care label or website for
product care instructions.
! Never use any glue until you are certain that the parts belong together.
! Bulky items such as wardrobes and bunk beds should be assembled in the room they will be
used in as they may not fit through a door once assembled.
! Always use a soft surface (such as carpet or cardboard) when assembling your product to
avoid scratching or damaging the surface of the product.
! The most common mistakes made during assembly are using the wrong hardware or getting
components back to front.
Unless instructed, do not fully tighten screws
until the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.

Top Panel
(P1)
Bottom
Panel
(P2)
Divider
(P3)
Leg
(P4)
Leg
(P4)
Leg
(P4) Leg
(P4)
Divider
(P3)
x 2
16 x Dowels
(H1)
8 x Small
Dowels
(H2)
8 x Long
Screws
(H12)
16 x Small
Screws
(H5)
12 x Cam
Bolts
(H3)
12 x Cam
Nuts
(H4)
8 x Small
Cam Nuts
(H11)
8 x Small
Cam Bolts
(H10)
5 x Plastic
Glides
(H14)
2 x Handles
(H15)
4 x Round
Head Bolts
(H16)
1 x Double
Ended
Screws
(H17)
2 x CL Runner
Tracks
(H6)
2 x CR Runner
Tracks
(H7)
2 x DL
Runners
(H8)
2 x DR
Runners
(H9)
Left
Drawer Side
(P6)
Right Drawer
Side
(P7)
Drawer Back
(P9)
Support
Leg
(P10)
Drawer
Base
(P8)
Drawer
Front
(P5)
4 x Inside
Hexagonal
Screws
(H13)
1 x Allen Key
(H18)
What you need
to assemble the product
Other tools you need
Flat head screwdriver; Phillips head
screwdriver; Hammer
Parts list
Box 1: Top Panel (P1); Bottom Panel (P2);
Divider (P3); Leg (P4); Drawer Front (P5);
Left Drawer Side (P6); Right Drawer Side
(P7); Drawer Base (P8); Drawer Back (P9);
Support Leg (P10);
www.fantasticfurniture.com.au PAGE 4
DO NOT USE

2 x CL Runner
Tracks (H6)
2 x CR Runner
Tracks (H7)
4 x Small
Dowels (H2)
1 x Allen
Key (H18)
(P1) (P4)
(P3)
(P3)
(P2)
(P3)
H3
H3
H3
H3
H3
H5
H6
H2
H13
H13
H13
H13
H2
H2
H2
H7
H5
H5
H5
H3
H3 H3
H3
4 x Inside
Hexagonal
Screws (H13)
H6
CL
H5
H7
CR
H5
Attach 8 x Cam Bolts (H3) into Top Panel (P1).
Attach 1 x Cam Bolts (H3) into Leg (P4). Repeat this step for the rest of 3 x Legs (P4).
Tighten Cam Bolts using a Phillips head screwdriver.
Insert 4 x Small Dowels (H2) into Dividers (P3).
Attach Dividers (P3) to Bottom Panel (P2) with
4 x Inside Hexagonal Screws (H13) using Allen Key (H18).
counter sunk holes
Attach 1 x CL Runner Tracks (H6) and 1 x CR Runner Tracks (H7) to Divider (P3)
with 4 x Small Screws (H5). Tighten Screws using a Phillips head screwdriver.
Repeat Step 2 for the other Diveder (P3).
H18
www.fantasticfurniture.com.au PAGE 5
You will need
Step 2
8 x Small
Screws (H5)
Phillips head
screwdriver
12 x Cam Bolts
(H3)
You will need
Step 1
Phillips head
screwdriver
You will need
Step 3

This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
(P2)
(P2) (P10)
(P4)
(P4)
(P4)
(P4)
H4
H4
H1
H1
H1 H1
H1
H1
H1 H1
H4
H14
H17
H4
Insert 4 x Dowels (H1) and 2 x Cam Nuts (H4) into the holes of Bottom Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach 2 x Legs (P4) to Bottom Panel (P2), then tighten the cam nuts using a Flat head screwdriver.
Insert 4 x Dowels (H1) and 2 x Cam Nuts (H4) into the holes of Bottom Panel (P2) as shown.
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach 2 x Legs (P4) to Bottom Panel (P2), then tighten the cam nuts using a Flat head screwdriver.
Attach Support Leg (P10) to Bottom Panel (P2) with 1 x Double Ended Screws (H17).
Hammer 5 x Plastic Glides (H14) on 4 x Legs (P4) and Support Leg (P10).
H14
H14
H14
H14
www.fantasticfurniture.com.au PAGE 6
You will need
Step 4
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
Flat head
screwdriver
You will need
Step 5
2 x Cam Nuts
(H4)
4 x Dowels
(H1)
5 x Plastic
Glides (H14)
1 x Double Ended
Screws (H17)
Flat head
screwdriver
Hammer

(P1)
(P4)
(P4)
(P3)
(P5)
(P4)
H1 H1
H1 H1
H2
H2
H1 H1
H4
H4
H4 H4
H4 H4
H4
H10 H10
H10 H10
Screw 4 x Small Cam Bolts (H10) into Drawer Front (P5) with a Phillips head screwdriver.
Insert 8 x Dowels (H1) into Legs (P4). Insert 4 x Small Dowels (H2) into Dividers (P3).
Insert 8 x Cam Nuts (H4) into the holes of Dividers (P3) and Legs (P4).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Attach Top Panel (P1) and tighten the cam nuts using a Flat head screwdriver.
www.fantasticfurniture.com.au PAGE 7
Phillips head
screwdriver
4 x Small Cam
Bolts (H10)
You will need
Step 6
8 x Cam Nuts
(H4)
8 x Dowels
(H1)
4 x Small
Dowels (H2)
Flat head
screwdriver
You will need
Step 7

(P5)
(P8)
(P6)
(P6)
(P7)
(P6)
(P7)
(P7)
(P9)
Slide Drawer Base (P8) into the groove
in Drawer Sides (P6) and (P7).
Attach Drawer Back (P9) to Drawer Sides (P6) and (P7)
with 4 x Long Screws (H12), make sure that the groove lines up
the whole way around the drawer.
Tighten Screws using a Phillips head screwdriver.
H12
H12
H12
H12
H11
H11
H11
H11
Insert 4 x Small Cam Nuts (H11) into the holes of Drawer Sides (P6) and (P7).
Rotate the cam nuts so the arrows point towards the incoming cam bolts.
Push
Drawer Sides (P6) and (P7) into place and tighten the cam nuts using a Flat head screwdriver.
This is how a cam nut works........
The head of the cam
bolt goes into the open
mouth of the cam nut.
You then turn the cam
nut so it tightens over
the bolt.
www.fantasticfurniture.com.au PAGE 8
Phillips head
screwdriver
You will need
4 x Small Cam
Nuts (H11)
Step 8
Step 9
Flat head
screwdriver
You will need
4 x Long
Screws(H12)
Step 10

4 x Small
Screws (H5)
You will need
1 x DL Runner
(H8)
1 x DR Runner
(H9)
(P6)
(P7)
(P5)
H9
H9
H8
H8
DR
DL
H5
H5 H5
H5
H15
H16
H16
Repeat step 7 to step 12 to assemble the other drawer.
Attach 1 x DL Runner (H8) to the bottom of Left Drawer Side (P6) and 1 x DR Runner (H9)
to the bottom of Right Drawer Side (P7) with 4 x Small Screws (H5).
Tighten Screws using a Phillips head screwdriver.
Attach 1 x Handle (H15) to Drawer Front (P5) with 2 x Round Head Bolts (H16).
Tighten Round Head Bolts using a Phillips head screwdriver.
H5
H5
H5
H5
Step 11
www.fantasticfurniture.com.au PAGE 9
Phillips head
screwdriver
You will need
1 x Handle
(H15)
2 x Round Head
Bolts (H16)
Step 12
Step 13
Phillips head
screwdriver

Put the drawers into the table.
Job Complete!
In the interest of our environment please dispose of all packaging thoughtfully.
www.fantasticfurniture.com.au PAGE 10
Step 14
Step 15
Recommended weight capacity : 80KG.