fantastic furniture Ryan User manual

Assembly Instructions
Ryan
3 Door Robe 1200mm - Oak

It is recommended the wardrobe is assembled in the
room that it is intended for.
(CLEAR FLOOR SPACE IN ROOM IF REQUIRED)

6 x HINGE & HINGE BLOCK
(H10)
1 x HANGING RAIL
(H4)
P1
P1
P3
P4
P5
P6
P7
P8
Page 3
16 x CONFIRMAT SCREWS
(H6)
1 x CONFIRMAT SCREW CAPS
(H7)
50 x NAILS
(H3)
x HANGING RAIL BRACKETS
(H5)
14 x 1/ 6g C/S SCREWS
(H9)
x T Z FITTING
(H1)
3 x 8MM NIB SCREW
(H )
P10
P2
P7
Hammer
P10
P11
3 x BOW HANDLES
(H11) 6 x HANDLE SREWS
(H1 )
8 x SHELF SUPPORTS
(H8)
P8
P9
6 x PLASTIC GLIDES
(H13)
P13
1 x WALL FIXING BRACKET
(H14)

ST P 1
P1
P1
P5
P2
P6
Page 4
1 Insert TZ fittings in to P1 and tap in with mallet.
2 Align dowels on P2 with holes on P5 and bring together.
3 Align dowels on P6 with holes on P5 and bring together.
4 Align dowels on P1 with holes on P5 and bring together.
Towards top edge
TZ Fitting (H1)
Knock into Parts 1
You will need:
x T Z Fitting (H1)
Note:
All raw edges should be
facing up and Oak
edges facing down in
this stage of assembling

P6
P1
P1
P2
P4
ST P 2
1 Insert the panel P4 between panels P2 & P6, align dowels with holes
and bring together.
2 Using 4 x Confirmat screws (H6) fix panel P4 in place through P2 & P6.
3 Place P3 on ends of P6, P2 & P1's, align dowels with holes and bring
together.
4 Using 6 x Confirmat screws (H6) fix panels P5 in place. Insert end caps
(H7) into the screws on side panel only.
P3
Page 5
P5
.
.
You will need:
10 x Confirmat Screws (H6)
6 x Confirmat screw Caps (H7)
. .
.
.
.
.
Note:
All raw edges should be
facing up and Oak
edges facing down in
this stage of assembling

ST P 3
P1
P1
P3
P5
1 Place unit on it's front, raw edge up, Oak edge facing down.
2 Using 6 x Confirmat screws (H6) fix panel (P3) in place. Insert end caps
(H7) into the screws on side panel only.
3 Fix panels (P1) with 2 x 28mm Nib screws (H2) through TZ fitting to Panel
(P2).
P6
P4
Page 6
8MM NIB
SCREW
THROUGH TZ
FITTING INTO
PART
.
. .
.
.
.
P2
You will need:
6 x Confirmat Screws (H6)
6 x Confirmat Screw Caps (H7)
x 8mm Nib Screw (H )
Note:
All raw edges should be
facing up and Oak
edges facing down in
this stage of assembling

ST P 4
P2
P3
. . . . . . . . . . .
. . . . . . . . . . . .
. . . . . . . . . . .
. . . . . . . . .
. . . . . . . . .
Page 7
P9
1 nsure the unit is on it's front, raw edge up, Oak edge facing down
2 Join the 2 smaller back panels (P8) with the connect strip (P13) as shown
above then place over the larger opening. Place the larger back panel P9
over the remaining opening.
3 Make sure the unit is square by placing a back panel in corner and aligning
the edges of wardrobe.
4 Nail in each corner of back panels P8 and P9 and work along the unit,
making sure to hammer in the nails close to the edge so the nail penetrates
the unit.
5 Gently hammer in Plastic glides to bottom edges of wardrobe.
You will need:
50 x nails (H3)
6 x Plastic Glides (H13)
P8
P8
.
.
.
.
. . . . . . . . . . . .
.
.
P13
Profile view of connector strip of backs P8
P8 P8
Top Of Strip P13
White Edge down
Note: op of strip (P13) to be facing
upwards when placing it on unit

ST P 5
Page 8
P3
P7
P8
P4
P2
P5
P7
P6
1. Stand unit upright.
2. Insert shelf supports (H8) into your preferred position inside the robe
and then insert shelf (P7)
3. Fix 6 hinge blocks (H10) to parts P3, P4, and P5 into the guide holes using
the screws provided on the hinge block, making sure the Hinge Block (H10)
is facing the right way. (see above picture)
4. Attach Hanging Rail Brackets (H5) into holes provided in P4 & P3 and fix to
unit using 2 x 1/2 6g C/S Screws (H9). Simply place the Hanging rail (H4)
Into brackets.
You will need:
x Hanging Rail Brakets(H5)
6 x Hinge Block (H10)
8 x Shelf Supports (H8)
x 1/ 6G C/S Screw (H9)
When attaching the hinge
block (H10) ensure that it is
positioned as shown above.
FACING
FRON
OF UNI
FACING
REAR OF
UNI

Page 9
ST P 6
1. Attach hinge (H10) to all doors (P10 & P11) using the 1 x 1/ 6G C/S Screw
(H9) using the pilot holes as shown in picture above.
. Working from the top down, Position the Hinge (H10) and the Hinge Block
(H10) together from the front of the Hinge Block first then simply click
together.
Note: he smaller doors P10 attach to P3 and P4 while the larger door P11
attaches to P5
You will need:
6 x Hinge (H10)
14 x 1/ 6G C/S Screw (H9)
1/ 6G C/S Screw
(H9)
Hinge (H10)
P10 & P11
Adjustment of Doors (More information on page 1 )
Snap-On System
The hinge arm is positioned on the mounting
plate and simply clipped on from front to
back.
It can easily be removed from the mounting
plate by pressing the back end of the hinge
arm which will release it from the block

1 To fit handles, place handles (H11) on the front of the door and use Handle Screw
(H1 ) to fix handle to the door from the inside of the unit.
We recommend the unit to be fixed to the wall, to do this you can use the Wall
Fixing Bracket (H14). Attach the Wall Fixing Bracket with the 8mm Nib Screw
(H ) through the bottom hole of the Wall Fixing Bracket (H14) to the back of the
unit along the top edge of Part (P6) so it aligns with the wall.
Consult you hardware specialist for which fastener is recommended for your wall
You will need:
3 x Bow Handle (H11)
6 x Handle Screw (H1 )
1 x Wall Fixing Bracket (H14)
1 x 8mm Nib Screw (H )
Page 10
ST P 7
P6