fantastic furniture Lunar King Single Loft Bunk User manual

fantasticfurniture.com.au
Version 1.0
Lunar
King Single Loft Bunk

Page 2
Looks like you’ve found
your Fantastic!
We’re thrilled you’ve chosen Fantastic Furniture
to help create a home you’ll love
fantasticfurniture.com.au
Love it? Shareit!
Fantastic buy! Share how it looks at home on Instagram for
your chance to win a $250 Fantastic Furniture Gift Card!
@fantasti cfurni ture
Helpful bunk bed safety tips
Bunk beds should be checked periodically to ensure that the guardrail, ladder and other
components are secure and in the correct position and all connectors are tight.
We recommend that children under the age of nine (9) do not use the upper bunk. Children
should be discouraged from playing on the bunk bed.
No more than one occupant should use the upper bunk at any time (unless otherwise stated).
Bunk beds should be placed a minimum of 2 metres away from any ceiling fans to prevent any
injury to the upper bunk occupant.
Recommended weight capacity : 10Kg/Shelf
10Kg/Drawer

fantasticfurniture.com.au Page 3
Read through the instructions
carefully before you begin.
Identify and lay out all of the
components before you begin assembly.
Unless instructed, do not fully tighten
screwsuntil the item is fully assembled.
Make sure you have all the required tools.
Never use power tools unless instructed.
! Never use power tools unless specifically instructed. They can damage your
components or hardware if used incorrectly.
!
!
The most common mistakes made during assembly are using the wrong hardware or
getting components back to front.
Always use a so t surface (such as carpet or cardboard) when assembling your
product to avoid scratching or damaging the surface of the product.
Assembly checklist
! Bulky items such as wardrobes and bunk beds should be assembled in the room they
will be used in as they may not fit through a door once assembled.
! Never use any glue until you are certain that the parts belong together.
! Periodically check and re-tighten all fasteners. Check the product care label or
website for product care instructions.
components please visit our website Help Centre for further assistance.
!Please see page 2for any safety requirements or weight restrictions.
Useful information

Page 4
fantasticfurniture.com.au
What You Need
to assemble the product
Other tools you need
Phillips Head Screwdriver;
Hammer
A
(P1)
(P2)
(P3)
(P3)
(P4)
(P6)
(P5)
(P5)
(P5)
(P5)
Rear Side Rail
Front Side Rail
Headboard/Footboard
Bottom Panel
Headboard/Footboard
Bed Base Panel
Bed Base Panel
Bed Support Bar
Bed Support Bar
(P6)
Bed Support Bar
(P5)
Bed Support Bar
Bottom Panel
Bed Support Bar (P4)
Box 1:
Rear Side Rail (P1)
Front Side Rail (P2)
2 x Headboard/Footboard Panels (P3)
Box 2:
Desk Side Panel (L) (P7)
Desk Side Panel (R) (P8)
Box 3:
5 x Bed Support Bars (P5)
Desk Top Panel (P9)
Desk Support Panel (P10)
Desk Panel (P11)
Desk Support Panel (P12)
Box 4:
2 x Bottom Panels (P4)
2 x Bed Base Panels (P6)
Support Panel (P39)
B
(P9)
(P7)
(P12)
(P8)
Desk Side Panel (L)
Desk Side Panel (R)
Desk Top Panel
Desk Support Panel
(P10)
Support Panel
(P39)
Support Panel

Page 5
fantasticfurniture.com.au
What You Need
to assemble the product
Other tools you need
Phillips Head screwdriver;Hammer
D
Ladder Middle Step
(P37)
(P35)
(P33)
Ladder Left Panel
Ladder Right
Panel
(P34)
Ladder Top Step
(P36)
Ladder Bottom Step
(P38)
Ladder Support Panel
C
(P39)
(P16) (P14)
(P26)
(P21)
(P13) (P19)
(P22)
(P17)
(P18)
(P30)
(P28)
(P29)
(P27)
(P31)
(P15) Robe Back Panel
(P24)
(P25)
(P23)
Robe Side Panel (L)
Robe Side Panel (R)
Robe Door Panel
Robe Middle Panel
Support Panel
Robe Support Panel (BTM)
Robe Fixed Panel
Robe Shelf Panel
Robe Fixed Panel
Robe Back Panel
Robe Front Support Panel
(P20)
Robe Front Support Panel
(P20)
Robe Bottom Panel
Robe Top Panel
Robe Back Support Panel
Drawer Right Panel
Drawer Support Panel
(P32)
Drawer Front Panel
Drawer Left Panel
Drawer Back Panel
Drawer Bottom Panel
Box 1:
Ladder Left Panel (P33)
Ladder Right Panel (P34)
3 x Ladder Support Panels (P35)
Ladder Top Step (P36)
Ladder Middle Step (P37)
Ladder Bottom Step (P38)
Box 2:
Robe Side Panel (L) (P13)
Robe Side Panel (R) (P14)
Robe Middle Panel (P15)
Robe Back Panel (P24)
Robe Door Panel (P25)
Box 4:
Robe Fixed Panel (P23)
3 x Drawer Side Panel (L) (P28)
3 x Drawer Side Panel (R) (P29)
3 x Drawer Back Panel (P30)
3 x Drawer Bottom Panel (P31)
Support Panel (P39)
Box 3:
Robe Top Panel (P16)
Robe Bottom Panel (P17)
2 x Robe Support Panels (P18)
Robe Fixed Panel (P19)
2 x Robe Front Support Panel (P20)
Robe Back Support Panel (P21)
Robe Back Panel (P22)
Robe Shelf Panel (P26)
3 x Drawer Front Panels (P27)
3 x Drawer Support Panel (P32)
x 3

Page 6
fantasticfurniture.com.au
What You Need
to assemble the product
Other tools you need
Phillips Head Screwdriver; Hammer
Hardware list:
33 x Screws 12 x Screws75 x Cam
Nuts (H1) (H2)
97 x Dowels 1 x Allen Key 21 x Screws
(H3) (H4) (H5) (H7) (H8)
(H9) (H10)
18 x Feet
Glides (H12)
75 x Cam Bolts
36 x Screws 33 x Nuts 4 x Shelf
Supports (H11)
4 x Handles 8 x Screws
(H14)
1 Door Stop
(H16)
3 x CL Runner
Track (H6a)
3 x DL Runner
(H6b)
3 x CR Runner
Track (H6c)
3 x DL Runner
(H6d)
4 x Braces (H6) 3 x Hinges
(H15)
18 x Screws
(H17)
38 x Screws
(H18)
1 x Hanging
Rail (H22)
5 x Cover
Stickers (H23)
12 x Screws
(H19)
2 x Screws
(H20)
2 x Hanging
Rail Supports
(H21)
Box 1A:
Box 1B:

fantasticfurniture.com.au
You will need
Step 1: To Assemble The Desk (B)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut. You
then turn the cam
nut so it tightens
over the bolt.
(H3)
(H1)
(H2)
(H2)
Phillips Head
Screwdriver
6 x Dowels (H3)
(H2)
3 x Cam Bolts
(H1)
3 x Cam Nuts
P10
P9
(H2)
(H3)
(H2)
(H2)
(H1)
(H1)
(H1)
Phillips Head
Screwdriver
P10
P9
(H3)
(H1)
(H2)
(H3)
(H3)
(H3)
(H3)
(H3)
Page 7
Insert 6 x Dowels (H3) into the Desk Top Panel (P9) and Desk Support Panel (P10).
Insert 3 x Cam Bolts (H2) into the Desk Top Panel (P9) by tightening with a Phillips Head
Screwdriver.
Insert 3 x Cam Nuts (H1) into Panel (P10). Rotate the Cam Nuts so the arrows are facing
the incoming Bolts.
You will need
Step 2
Attach the Desk Support Panel (P10) to the Desk Top Panel (P9), by tightening the
Cam Nuts with the Phillips Head Screwdriver.
This side has raw edge
This side has covered
edge

(H3)
Page 8
fantasticfurniture.com.au
You will need
Step 3
You will need
Phillips Head
Screwdriver
Step 4
(H2)
P12
P11
(H3)
(H3)
(H3)
(H3)
(H1)
(H2)
(H1)
(H2)
(H3)
Phillips Head
Screwdriver
10 x Dowels (H3)
(H2)
(H1)
3 x Cam Nuts
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
3 x Cam Bolts
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H2)
(H1)
(H1)
(H1)
(H2)
(H2)
P12
P11
Insert 10 x Dowels (H3) into Desk Panel (P11) and Desk Support Panel (P12).
Insert 3 x Cam Bolts (H2) into the Desk Panel (P11), by tightening with the
Phillips Head Screwdriver.
Insert 3 x Cam Nuts (H1) into the Desk Support Panel (P12). Rotate the Cam Nuts
so the arrows are facing the incoming Bolts.
Attach the Desk Support Panel (P12) to the Desk
Panel (P11), by tightening the Cam Nuts with the
Phillips Head Screwdriver.

Page 9
fantasticfurniture.com.au
You will need
Step 5
Phillips Head
Screwdriver
You will need
Phillips Head
Screwdriver
Step 6
(H1)
(H2)
(H3)
(H2)
P11
P12
P9
P10
(H1)
(H2)
(H1)
(H1)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
P7
P8
(H1)
(H1)
(H1)
(H1)
(H1)
(H2)(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H1)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2)
18 x Cam Bolts
P7
P8
(H1)
18 x Cam Nuts
Insert 18 x Cam Bolts (H2) into the Left and Right Desk Side Panels (P7 & P8),
by tightening with the Phillips Head Screwdriver.
Insert 18 x Cam Nuts (H1) into panels (P9, P10, P11 & P12). Rotate the Cam Nuts so the
arrows are facing the incoming Bolts.
First attach the Left Desk Side Panel (P7) to panels (P9, P10, P11 & P12), by aligning all the
holes and tightening all the Cam Nuts with a Phillips Head Screwdriver.
Then repeat process to attach the Right Desk Panel (P8) to panels (P9, P10, P11 & P12).
This side has covered
edge facing up

Page 10
fantasticfurniture.com.au
You will need
Step 7
Step 8
Hammer
6 x Feet Glides
(H12)
(H12)
P12
P7
P8
(H12)
(H12)
(H12)
(H12)
(H12)
Attach 6 x Feet Glides (H12) to the underside of the Desk Side Panels (P7 & P8) and the
Desk Support Panel (P12), gently using a Hammer or Soft Headed Mallet.
The Desk (B) section is now complete.
Carefully lift the assembled desk and put upright.

PPage 111
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
You will need
Step 10
(H2)
19 x Cam Bolts 3 x CL Runner
Tracks (H6a)
3 x CR Runner
Track (H6c)
10 x Screws
(H18)
1 x Hanging Rail
Support (H21)
(H21)
(H18)
(H2)
(H2)
(H2)
(H2)
(H2)
(H2) (H2)
(H2)
(H2)
(H2)
(H6c)
(H6c)
(H6c)
(H18)
(H18)
(H18)
(P15)
(P15)
11 x Cam Bolts
(H2)
10 x Screws
(H18)
1 x Hanging Rail
Support (H21)
Phillps head
Screwdriver
(H16)
1 x Door Stop
2 x Screws
(H20)
(H20)
(H16)
(H2)
Insert 19 x Cam Bolts (H2) into Left Robe Side Panel (P13) and Right Robe Side Panel (P14), by tightening with the Phillips
Head Screwdriver.
Attach 3 x CL Runner Tracks to the Left Robe Side Panel (P13) with 9 x Screws (H18), by tightening with a Phillips Head
Screwdriver.
Attach the Hanging Rail Support (H21) to the Right Robe Side Panel (P14) with 1 x Screw (H18), by tightening with a
Phillips Head Screwdriver.
Insert 5 x Cam Bolts (H2) into the Middle Robe Panel (P15), by tightening with a Phillips Head Screwdriver.
Attach 3 x Right Runner Tracks (H6c) to the Middle Robe Panel (P15) with 9 x Screws (H18), tightening with the
Phillips Head Screwdriver.
Then flip Panel (P15) onto its side, and insert 6 x Cam Bolts (H2) into the Middle Robe Panel (P15), tightening with a
Phillips Head Screwdriver.
Attach the Hanging Rail Support (H21) to the Middle Robe Panel (P15) with 1 x Screw (H18), by tightening with a
Phillips Head Screwdriver.
Attach the Door Stop (H16) with 2 x Screws (H20), by tightening with a Phillips Head Screwdriver.
Flip this panel
on its side
Step 9: To Assemble The Robe (C)
(H18)
(H6c)

Page 12
fantasticfurniture.com.au
You will need
You will need
Step 11
Step 12
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
P19
Phillips Head
Screwdriver
10 x Dowels (H3)
(H1)
10 x Cam Nuts
P21
(P20) x2
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
Insert 10 x Dowels (H3) into Robe Fixed Panel (P19), 2 x Robe Front Support Panels (P20) and
the Robe Back Support Panel (P21).
Insert 10 x Cam Nuts (H1) into Panels (P19, P20 & P21). Rotate the Cam Nuts so the arrows are
facing the incoming Bolts.
Attach Panels (P19, P20, P21) to Left Robe Side Panel (P13), by aligning the holes
and tightening the Cam Nuts with the Phillips Head Screwdriver.
P13
P19
P21
P20
P20

Page 13
fantasticfurniture.com.au
You will need
Step 13
Phillips Head
Screwdriver
You will need
4 x Dowels (H3)
Step 14
Attach the Middle Robe Panel (P15) to panels (P19, P20 & P21), by aligning all the holes, and
tightening the Cam Nuts with a Phillips Head Screwdriver.
Slot in the Robe Back Panel (P22) into the grooves of panels (P13, P15 & P21).
Insert 4 x Dowels (H3) into the Middle Robe Panel (P15).
ÿ
P15
P19 P21
P20
P20
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
(H3)
(H3)
P15
P22
P21
P13
(H3)
(H3)
P13
Raw side

Page 14
fantasticfurniture.com.au
Step 15
You will need
Phillips Head
Screwdriver
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
6 x Dowels
(H3)
(H1)
4 x Cam Nuts
Step 16
Insert 6 x Dowels (H3) into the Robe Bottom Panel (P17).
Attach the 2 x Robe Support Panels (P18) to the Robe Bottom Panel (P17) by aligning the holes.
Insert 6 x Dowels (H3) into the Robe Side Panel (P13).
Attach the Robe Top Panel (P16) to Robe Side Panel (P13) and Robe Middle Panel
(P15) by aligning the holes, and tightening the Cam Nuts with a Phillips Head
Screwdriver.
Secure The Robe Top Panel (P16) with 2 x Screws (H5) tightening with a Phillips Head
Screwdriver.
Repeat process to attach the Robe Bottom Panel (P17) to Panel (P13 & P15).
You will need
6 x Dowels (H3)
(H3)
P18
(H3)
(H3)
P17
P18
(H3)
(H3)
(H3)
4 x Screws
(H5)
P16
P15 P17
(H5)
(H3)
(H3)
(H3)
(H5)
(H5)
P18)
P18
P13
P13
(H3)
(H3)
P17 P18
(H1)
(H1)
P13
(H3)
P16
This side has
raw edge

Page 15
fantasticfurniture.com.au
Step 17
You will need
(H3)
P16
P17
P24
P23
P18
P18
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H3)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
(H1)
Step 18
You will need
Phillips Head
Screwdriver
6 x Dowels
(H3)
(H1)
6 x Cam Nuts
P16
P15
P24
P23
P17
(H1)
(H2)
Insert 6 x Dowels (H3) and 6 x Cam Nuts (H1) into the Robe Back Panel (P24) and Robe Fixed
Shelf (P23). Rotate the Cam Nuts so the arrows face the incoming Bolts.
Attach the Robe Fixed Shelf (P23) and Robe Back Panel (P24) to the Middle Robe Panel (P15),
by tightening the Cam Nuts with the Phillips Head Screwdriver.
(H3)
Please note the Fixed
Shelf (P23) is optional
12 x Dowels
(H3)
(H1)
10 x Cam Nuts
Insert 10 x Cam Nuts (H1) and 12 x Dowels (H3) into Panels (P16, P17, P18, P23 & P24).
This side has
covered edge
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.

Page 16
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
P14
(H1)
(H1)
(H1)
(H1)
P16
P17
P24
P23
P18
P18
This is how a cam nut works........
The head of the
cam bolt goes into
the open mouth of
the cam nut.You
then turn the cam
nut so it tightens
over the bolt.
Step 19
Attach the Right Robe Side Panel (P14) to Panels (P16,
P17, P18, P23 & P24) by aligning the holes, and tightening
the Cam Nuts with the Phillips Head Screwdriver.
You will need
Step 20
4 x Screws
(H5)
Phillips Head
Screwdriver
P14
(H5)
(H5)
P24
P18
P16
P18
P17
(H12)
(H12)
(H12)
(H12)
(H12)
(H12)
(H12)
(H5)
(H5)
Hammer
(H12)
(H12)
8 x Feet Glides
Secure the Robe Back Panel (P24) to the Robe Top Panel (P16) and Robe Bottom Panel (P17) with
4 x Screws (H5), tightening with the Phillips Head Screwdriver.
Attach the 8 x Feet Glides (H12) to the bottom of Panels (P13, P14 & P18) by gently using a
Hammer or Soft Headed Mallet.
P13

Page 17
fantasticfurniture.com.au
You will need (H15)
(H19)
(H19)
(H19)
(H15)
(H15)
P25
P25
P27
(H13) (H14)
(H15) (H19)
1 x Handle 2 x Screws
3 x Hinges 6 x Screws
(H13)
(H14)
Phillips Head
Screwdriver
Step 21
(H14)
Attach 3 x Hinges (H15) to the Robe Door (P25), using 6 x Screws (H19) and tightening with the
Phillips Head Screwdriver.
Attach the Handle (H13) to the Robe Door (P25) using 2 x Screws (H14), tightening with the
Phillips Head Screwdriver.
You will need
Step 22
Phillips Head
Screwdriver
(H2)
(H2)
(H2)
P27
(H2)
15 x Cam Bolts
Insert 5 x Cam Bolts (H2) into the Drawer Front Panel (P27), tightening with the Phillips Head
Screwdriver.
Repeat for the remaining drawers.
x3

Page
fantasticfurniture.com.au
You will need
Step 23
Phillips Head
Screwdriver
Step 24
18
Insert 5 x Cam Nuts into the Drawer Side Panels (P28 & P29) and Drawer Support Panels (P32).
Rotate the Cam Nuts so the arrows point towards the incoming Cam Bolts. Attach the Drawer
Front Panel (P27) to the Drawer Side Panels (P29 & P28) and Drawer Support Panel (P32), by
tightening Cam Nuts with the Phillips Head Screwdriver.
Repeat for the remaining drawers.
x3
P29
P32
P28
P27
(H1)
(H1)
(H1)
(H1)
(H1)
15 x Cam Nuts
Slide in the Drawer Base Panel (P31) into the grooves of the Drawer Front Panel (P27)
and Drawer Side Panels (P28 & P29).
Repeat for remaining drawers.
P31
P28
P29
P27
P32
Raw side facing bottom
x3

Page
fantasticfurniture.com.au
Step 25
19
(H17)
You will need
Phillips Head
Screwdriver
18 x Screws
(H17)
P29
P31
(H17)
P32
P28
(H17)
(H17)
P30
Secure the Drawer Back Panel (P30) to the Drawer Side Panels (P28 & P29) and the Drawer
Support Panel (P32) with 6 x Screws (H17), tightening with the Phillips Head Screwdriver.
Ensure that the Drawer Base Panel (P31) slots in the groove of the Drawer Back Panel (P30).
Repeat process for remaining drawers.
You will need
Step 26
Phillips Head
Screwdriver
Attach the 3 x Handles (H13) to the 3 x Drawer Fronts (P27) with 6 x Handle Screws (H14),
by tightening with a Phillips Head Screwdriver.
(H14)
6 x Screws
x3
(H13)
3 x Handles
(H14)
(H13)
x3
P27

Page 20
fantasticfurniture.com.au
You will need
Phillips Head
Screwdriver
Step 27
(H6d)
(H18)
3 x DL Runner
(H6b) H6d)
3 x DR Runner
18 x Screws
(H18)
P29
P28
(H6b)
(H6d)
(H18)
(H18)
Attach 1 x Left Drawer Runner (H6b) to the Left Drawer Side Panel (P28), and 1 x Right
Drawer Runner (H6d) to the Right Drawer Side Panel (P29), using 6 x Screws (H18),
tightening with the Phillips Head Screwdriver. Repeat process for remaining drawers.
x3